Lines Matching +full:snvs +full:- +full:rtc
1 // SPDX-License-Identifier: (GPL-2.0 OR MIT)
8 rtc0 = &rtc;
14 compatible = "mmc-pwrseq-simple";
15 pinctrl-names = "default";
16 pinctrl-0 = <&pinctrl_usdhc1_gpio>;
17 reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
19 clock-names = "ext_clock";
20 post-power-on-delay-ms = <80>;
30 cpu-supply = <&buck2_reg>;
34 cpu-supply = <&buck2_reg>;
38 cpu-supply = <&buck2_reg>;
42 cpu-supply = <&buck2_reg>;
47 opp-1200000000 {
48 opp-microvolt = <950000>;
53 operating-points-v2 = <&ddrc_opp_table>;
55 ddrc_opp_table: opp-table {
56 compatible = "operating-points-v2";
58 opp-25000000 {
59 opp-hz = /bits/ 64 <25000000>;
62 opp-100000000 {
63 opp-hz = /bits/ 64 <100000000>;
66 opp-800000000 {
67 opp-hz = /bits/ 64 <800000000>;
73 pinctrl-names = "default";
74 pinctrl-0 = <&pinctrl_fec1>;
75 phy-mode = "rgmii-id";
76 phy-handle = <ðphy0>;
77 phy-supply = <&buck6_reg>;
78 phy-reset-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
79 fsl,magic-packet;
83 #address-cells = <1>;
84 #size-cells = <0>;
86 ethphy0: ethernet-phy@0 {
87 compatible = "ethernet-phy-ieee802.3-c22";
94 pinctrl-names = "default";
95 pinctrl-0 = <&pinctrl_flexspi>;
100 #address-cells = <1>;
101 #size-cells = <1>;
102 compatible = "jedec,spi-nor";
103 spi-max-frequency = <80000000>;
104 spi-tx-bus-width = <1>;
105 spi-rx-bus-width = <4>;
110 clock-frequency = <400000>;
111 pinctrl-names = "default";
112 pinctrl-0 = <&pinctrl_i2c1>;
118 pinctrl-names = "default";
119 pinctrl-0 = <&pinctrl_pmic>;
120 interrupt-parent = <&gpio1>;
122 rohm,reset-snvs-powered;
123 #clock-cells = <0>;
125 clock-output-names = "clk-32k-out";
129 regulator-name = "buck1";
130 regulator-min-microvolt = <700000>;
131 regulator-max-microvolt = <1300000>;
132 regulator-boot-on;
133 regulator-always-on;
134 regulator-ramp-delay = <1250>;
138 regulator-name = "buck2";
139 regulator-min-microvolt = <700000>;
140 regulator-max-microvolt = <1300000>;
141 regulator-boot-on;
142 regulator-always-on;
143 regulator-ramp-delay = <1250>;
144 rohm,dvs-run-voltage = <1000000>;
145 rohm,dvs-idle-voltage = <900000>;
150 regulator-name = "buck3";
151 regulator-min-microvolt = <700000>;
152 regulator-max-microvolt = <1350000>;
153 regulator-boot-on;
154 regulator-always-on;
159 regulator-name = "buck4";
160 regulator-min-microvolt = <3000000>;
161 regulator-max-microvolt = <3300000>;
162 regulator-boot-on;
163 regulator-always-on;
168 regulator-name = "buck5";
169 regulator-min-microvolt = <1605000>;
170 regulator-max-microvolt = <1995000>;
171 regulator-boot-on;
172 regulator-always-on;
177 regulator-name = "buck6";
178 regulator-min-microvolt = <800000>;
179 regulator-max-microvolt = <1400000>;
180 regulator-boot-on;
181 regulator-always-on;
185 regulator-name = "ldo1";
186 regulator-min-microvolt = <1600000>;
187 regulator-max-microvolt = <3300000>;
188 regulator-boot-on;
189 regulator-always-on;
193 regulator-name = "ldo2";
194 regulator-min-microvolt = <800000>;
195 regulator-max-microvolt = <900000>;
196 regulator-boot-on;
197 regulator-always-on;
201 regulator-name = "ldo3";
202 regulator-min-microvolt = <1800000>;
203 regulator-max-microvolt = <3300000>;
204 regulator-boot-on;
205 regulator-always-on;
209 regulator-name = "ldo4";
210 regulator-min-microvolt = <900000>;
211 regulator-max-microvolt = <1800000>;
212 regulator-boot-on;
213 regulator-always-on;
217 regulator-name = "ldo6";
218 regulator-min-microvolt = <900000>;
219 regulator-max-microvolt = <1800000>;
220 regulator-boot-on;
221 regulator-always-on;
228 clock-frequency = <400000>;
229 pinctrl-names = "default";
230 pinctrl-0 = <&pinctrl_i2c3>;
236 read-only; /* Manufacturing EEPROM programmed at factory */
240 rtc: rtc@51 { label
247 pinctrl-names = "default";
248 pinctrl-0 = <&pinctrl_uart1>;
249 assigned-clocks = <&clk IMX8MN_CLK_UART1>;
250 assigned-clock-parents = <&clk IMX8MN_SYS_PLL1_80M>;
251 uart-has-rtscts;
255 compatible = "brcm,bcm43438-bt";
256 shutdown-gpios = <&gpio2 6 GPIO_ACTIVE_HIGH>;
257 host-wakeup-gpios = <&gpio2 8 GPIO_ACTIVE_HIGH>;
258 device-wakeup-gpios = <&gpio2 7 GPIO_ACTIVE_HIGH>;
260 max-speed = <4000000>;
261 clock-names = "extclk";
266 #address-cells = <1>;
267 #size-cells = <0>;
268 pinctrl-names = "default", "state_100mhz", "state_200mhz";
269 pinctrl-0 = <&pinctrl_usdhc1>;
270 pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
271 pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
272 vmmc-supply = <&buck4_reg>;
273 vqmmc-supply = <&buck5_reg>;
274 bus-width = <4>;
275 non-removable;
276 cap-power-off-card;
277 keep-power-in-suspend;
278 mmc-pwrseq = <&usdhc1_pwrseq>;
283 compatible = "brcm,bcm4329-fmac";
284 pinctrl-names = "default";
285 pinctrl-0 = <&pinctrl_wlan>;
286 interrupt-parent = <&gpio2>;
288 interrupt-names = "host-wake";
293 pinctrl-names = "default", "state_100mhz", "state_200mhz";
294 pinctrl-0 = <&pinctrl_usdhc3>;
295 pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
296 pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
297 bus-width = <8>;
298 non-removable;
303 pinctrl-names = "default";
304 pinctrl-0 = <&pinctrl_wdog>;
305 fsl,ext-reset-output;
391 pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
402 pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
429 pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
445 pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {