dts/freescale/imx8mm-tqma8mqml-mba8mx.dts

1 // SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
3  * Copyright 2020-2021 TQ-Systems GmbH
6 /dts-v1/;
8 #include "imx8mm-tqma8mqml.dtsi"
12 	model = "TQ-Systems GmbH i.MX8MM TQMa8MxML on MBa8Mx";
13 	compatible = "tq,imx8mm-tqma8mqml-mba8mx", "tq,imx8mm-tqma8mqml", "fsl,imx8mm";
24 	reg_usdhc2_vmmc: regulator-vmmc {
25 		compatible = "regulator-fixed";
26 		pinctrl-names = "default";
27 		pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
28 		regulator-name = "VSD_3V3";
29 		regulator-min-microvolt = <3300000>;
30 		regulator-max-microvolt = <3300000>;
32 		enable-active-high;
33 		startup-delay-us = <100>;
34 		off-on-delay-us = <12000>;
38 		compatible = "gpio-usb-b-connector", "usb-b-connector";
41 		pinctrl-names = "default";
42 		pinctrl-0 = <&pinctrl_usb1_connector>;
43 		id-gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
46 			#address-cells = <1>;
47 			#size-cells = <0>;
52 					remote-endpoint = <&usb1_drd_sw>;
63 		gpio-controller;
64 		#gpio-cells = <2>;
65 		vcc-supply = <&reg_vcc_3v3>;
66 		pinctrl-names = "default";
67 		pinctrl-0 = <&pinctrl_expander>;
68 		interrupt-parent = <&gpio1>;
70 		interrupt-controller;
71 		#interrupt-cells = <2>;
81 	reset-gpio = <&expander0 14 GPIO_ACTIVE_LOW>;
84 	assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>,
86 	assigned-clock-rates = <10000000>, <250000000>;
87 	assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_50M>,
93 	assigned-clocks = <&clk IMX8MM_CLK_SAI3>;
94 	assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
95 	clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3", "pll8k", "pll11k";
103 	clock-names = "mclk";
108 	assigned-clocks = <&clk IMX8MM_CLK_UART1>;
109 	assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
113 	assigned-clocks = <&clk IMX8MM_CLK_UART2>;
114 	assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
118 	pinctrl-names = "default";
119 	pinctrl-0 = <&pinctrl_usbotg1>;
121 	srp-disable;
122 	hnp-disable;
123 	adp-disable;
124 	power-active-high;
125 	over-current-active-low;
126 	usb-role-switch;
131 			remote-endpoint = <&usb_dr_connector>;
138 	disable-over-current;
139 	vbus-supply = <&reg_hub_vbus>;
253 	pinctrl_usb1_connector: usb1-connectorgrp {
271 	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
281 	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {