Lines Matching +full:reset +full:- +full:snvs +full:- +full:powered
1 // SPDX-License-Identifier: (GPL-2.0 OR MIT)
13 compatible = "mmc-pwrseq-simple";
14 pinctrl-names = "default";
15 pinctrl-0 = <&pinctrl_usdhc1_gpio>;
16 reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
18 clock-names = "ext_clock";
19 post-power-on-delay-ms = <80>;
29 cpu-supply = <&buck2_reg>;
33 cpu-supply = <&buck2_reg>;
37 cpu-supply = <&buck2_reg>;
41 cpu-supply = <&buck2_reg>;
45 operating-points-v2 = <&ddrc_opp_table>;
47 ddrc_opp_table: opp-table {
48 compatible = "operating-points-v2";
50 opp-25000000 {
51 opp-hz = /bits/ 64 <25000000>;
54 opp-100000000 {
55 opp-hz = /bits/ 64 <100000000>;
58 opp-750000000 {
59 opp-hz = /bits/ 64 <750000000>;
65 pinctrl-names = "default";
66 pinctrl-0 = <&pinctrl_fec1>;
67 phy-mode = "rgmii-id";
68 phy-handle = <ðphy0>;
69 fsl,magic-packet;
73 #address-cells = <1>;
74 #size-cells = <0>;
76 ethphy0: ethernet-phy@0 {
77 compatible = "ethernet-phy-ieee802.3-c22";
84 pinctrl-names = "default";
85 pinctrl-0 = <&pinctrl_flexspi>;
90 #address-cells = <1>;
91 #size-cells = <1>;
92 compatible = "jedec,spi-nor";
93 spi-max-frequency = <80000000>;
94 spi-tx-bus-width = <1>;
95 spi-rx-bus-width = <4>;
100 clock-frequency = <400000>;
101 pinctrl-names = "default";
102 pinctrl-0 = <&pinctrl_i2c1>;
108 pinctrl-names = "default";
109 pinctrl-0 = <&pinctrl_pmic>;
110 interrupt-parent = <&gpio1>;
112 rohm,reset-snvs-powered;
114 #clock-cells = <0>;
116 clock-output-names = "clk-32k-out";
120 regulator-name = "buck1";
121 regulator-min-microvolt = <700000>;
122 regulator-max-microvolt = <1300000>;
123 regulator-boot-on;
124 regulator-always-on;
125 regulator-ramp-delay = <1250>;
129 regulator-name = "buck2";
130 regulator-min-microvolt = <700000>;
131 regulator-max-microvolt = <1300000>;
132 regulator-boot-on;
133 regulator-always-on;
134 regulator-ramp-delay = <1250>;
135 rohm,dvs-run-voltage = <1000000>;
136 rohm,dvs-idle-voltage = <900000>;
141 regulator-name = "buck3";
142 regulator-min-microvolt = <700000>;
143 regulator-max-microvolt = <1350000>;
144 regulator-boot-on;
145 regulator-always-on;
150 regulator-name = "buck4";
151 regulator-min-microvolt = <3000000>;
152 regulator-max-microvolt = <3300000>;
153 regulator-boot-on;
154 regulator-always-on;
159 regulator-name = "buck5";
160 regulator-min-microvolt = <1605000>;
161 regulator-max-microvolt = <1995000>;
162 regulator-boot-on;
163 regulator-always-on;
168 regulator-name = "buck6";
169 regulator-min-microvolt = <800000>;
170 regulator-max-microvolt = <1400000>;
171 regulator-boot-on;
172 regulator-always-on;
176 regulator-name = "ldo1";
177 regulator-min-microvolt = <1600000>;
178 regulator-max-microvolt = <3300000>;
179 regulator-boot-on;
180 regulator-always-on;
184 regulator-name = "ldo2";
185 regulator-min-microvolt = <800000>;
186 regulator-max-microvolt = <900000>;
187 regulator-boot-on;
188 regulator-always-on;
192 regulator-name = "ldo3";
193 regulator-min-microvolt = <1800000>;
194 regulator-max-microvolt = <3300000>;
195 regulator-boot-on;
196 regulator-always-on;
200 regulator-name = "ldo4";
201 regulator-min-microvolt = <900000>;
202 regulator-max-microvolt = <1800000>;
203 regulator-boot-on;
204 regulator-always-on;
208 regulator-name = "ldo6";
209 regulator-min-microvolt = <900000>;
210 regulator-max-microvolt = <1800000>;
211 regulator-boot-on;
212 regulator-always-on;
219 clock-frequency = <400000>;
220 pinctrl-names = "default";
221 pinctrl-0 = <&pinctrl_i2c3>;
227 read-only; /* Manufacturing EEPROM programmed at factory */
238 pinctrl-names = "default";
239 pinctrl-0 = <&pinctrl_uart1>;
240 assigned-clocks = <&clk IMX8MM_CLK_UART1>;
241 assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
242 uart-has-rtscts;
246 compatible = "brcm,bcm43438-bt";
247 shutdown-gpios = <&gpio2 6 GPIO_ACTIVE_HIGH>;
248 host-wakeup-gpios = <&gpio2 8 GPIO_ACTIVE_HIGH>;
249 device-wakeup-gpios = <&gpio2 7 GPIO_ACTIVE_HIGH>;
251 max-speed = <4000000>;
252 clock-names = "extclk";
257 #address-cells = <1>;
258 #size-cells = <0>;
259 pinctrl-names = "default", "state_100mhz", "state_200mhz";
260 pinctrl-0 = <&pinctrl_usdhc1>;
261 pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
262 pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
263 bus-width = <4>;
264 non-removable;
265 cap-power-off-card;
266 keep-power-in-suspend;
267 mmc-pwrseq = <&usdhc1_pwrseq>;
272 compatible = "brcm,bcm4329-fmac";
273 pinctrl-names = "default";
274 pinctrl-0 = <&pinctrl_wlan>;
275 interrupt-parent = <&gpio2>;
277 interrupt-names = "host-wake";
282 pinctrl-names = "default", "state_100mhz", "state_200mhz";
283 pinctrl-0 = <&pinctrl_usdhc3>;
284 pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
285 pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
286 bus-width = <8>;
287 non-removable;
292 pinctrl-names = "default";
293 pinctrl-0 = <&pinctrl_wdog>;
294 fsl,ext-reset-output;
380 pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
391 pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
418 pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
434 pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {