ti/omap/am335x-wega.dtsi

1 // SPDX-License-Identifier: GPL-2.0-only
8 	model = "Phytec AM335x phyBOARD-WEGA";
9 	compatible = "phytec,am335x-wega", "phytec,am335x-phycore-som", "ti,am33xx";
12 		compatible = "simple-audio-card";
13 		simple-audio-card,name = "snd-wega";
14 		simple-audio-card,format = "i2s";
15 		simple-audio-card,bitclock-master = <&sound_iface_main>;
16 		simple-audio-card,frame-master = <&sound_iface_main>;
17 		simple-audio-card,mclk-fs = <32>;
18 		simple-audio-card,widgets =
22 		simple-audio-card,routing =
30 		simple-audio-card,cpu {
31 			sound-dai = <&mcasp0>;
34 		sound_iface_main: simple-audio-card,codec {
35 			sound-dai = <&tlv320aic3007>;
42 		compatible = "regulator-fixed";
43 		regulator-name = "vcc3v3";
44 		regulator-min-microvolt = <3300000>;
45 		regulator-max-microvolt = <3300000>;
46 		regulator-boot-on;
52 	mcasp0_pins: pinmux-mcasp0-pins {
53 		pinctrl-single,pins = <
65 		#sound-dai-cells = <0>;
68 		AVDD-supply = <&vcc3v3>;
69 		IOVDD-supply = <&vcc3v3>;
70 		DRVDD-supply = <&vcc3v3>;
71 		DVDD-supply = <&vdig1_reg>;
77 	#sound-dai-cells = <0>;
78 	pinctrl-names = "default";
79 	pinctrl-0 = <&mcasp0_pins>;
80 	op-mode = <0>; /* DAVINCI_MCASP_IIS_MODE */
81 	tdm-slots = <2>;
82 	serial-dir = <
83 		2 1 0 0 /* # 0: INACTIVE, 1: TX, 2: RX */
85 	tx-num-evt = <16>;
86 	rx-num-evt = <16>;
93 	dcan1_pins: pinmux-dcan1-pins {
94 		pinctrl-single,pins = <
102 	pinctrl-names = "default";
103 	pinctrl-0 = <&dcan1_pins>;
109 	ethernet1_pins: pinmux-ethernet1-pins {
110 		pinctrl-single,pins = <
131 	phy-handle = <&phy1>;
132 	phy-mode = "mii";
133 	ti,dual-emac-pvid = <2>;
137 	phy1: ethernet-phy@1 {
143 	pinctrl-names = "default";
144 	pinctrl-0 = <&ethernet0_pins &ethernet1_pins>;
149 	mmc1_pins: pinmux-mmc1-pins {
150 		pinctrl-single,pins = <
163 	vmmc-supply = <&vcc3v3>;
164 	bus-width = <4>;
165 	pinctrl-names = "default";
166 	pinctrl-0 = <&mmc1_pins>;
167 	cd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
173 	regulator-boot-on;
174 	regulator-always-on;
179 	uart0_pins: pinmux-uart0-pins {
180 		pinctrl-single,pins = <
186 	uart1_pins: pinmux-uart1-pins {
187 		pinctrl-single,pins = <
197 	pinctrl-names = "default";
198 	pinctrl-0 = <&uart0_pins>;
203 	pinctrl-names = "default";
204 	pinctrl-0 = <&uart1_pins>;