ti/omap/am335x-myirtech-myc.dtsi

1 // SPDX-License-Identifier: GPL-2.0-or-later
2 /* SPDX-FileCopyrightText: Alexander Shiyan, <shc_work@mail.ru> */
5 /* Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ */
7 /dts-v1/;
11 #include <dt-bindings/interrupt-controller/irq.h>
12 #include <dt-bindings/leds/common.h>
15 	model = "MYIR MYC-AM335X";
16 	compatible = "myir,myc-am335x", "ti,am33xx";
20 			cpu0-supply = <&vdd_core>;
21 			voltage-tolerance = <2>;
31 		compatible = "fixed-clock";
32 		clock-frequency = <32768>;
34 		#clock-cells = <0>;
38 		compatible = "regulator-fixed";
39 		regulator-name = "vdd-mod";
40 		regulator-always-on;
41 		regulator-boot-on;
45 		compatible = "regulator-fixed";
46 		regulator-name = "vdd-core";
47 		regulator-always-on;
48 		regulator-boot-on;
49 		vin-supply = <&vdd_mod>;
53 		compatible = "gpio-leds";
54 		pinctrl-names = "default";
55 		pinctrl-0 = <&led_mod_pins>;
61 			default-state = "off";
62 			panic-indicator;
68 	pinctrl-names = "default", "sleep";
69 	pinctrl-0 = <&eth_slave1_pins_default>;
70 	pinctrl-1 = <&eth_slave1_pins_sleep>;
75 	phy-handle = <&phy0>;
76 	phy-mode = "rgmii-id";
77 	ti,dual-emac-pvid = <1>;
85 	pinctrl-names = "default", "sleep";
86 	pinctrl-0 = <&mdio_pins_default>;
87 	pinctrl-1 = <&mdio_pins_sleep>;
89 	phy0: ethernet-phy@4 {
94 &elm {
99 	pinctrl-names = "default", "sleep";
100 	pinctrl-0 = <&nand_pins_default>;
101 	pinctrl-1 = <&nand_pins_sleep>;
106 		compatible = "ti,omap2-nand";
108 		interrupt-parent = <&gpmc>;
110 		nand-bus-width = <8>;
111 		rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>;
112 		gpmc,device-width = <1>;
113 		gpmc,sync-clk-ps = <0>;
114 		gpmc,cs-on-ns = <0>;
115 		gpmc,cs-rd-off-ns = <44>;
116 		gpmc,cs-wr-off-ns = <44>;
117 		gpmc,adv-on-ns = <6>;
118 		gpmc,adv-rd-off-ns = <34>;
119 		gpmc,adv-wr-off-ns = <44>;
120 		gpmc,we-on-ns = <0>;
121 		gpmc,we-off-ns = <40>;
122 		gpmc,oe-on-ns = <0>;
123 		gpmc,oe-off-ns = <54>;
124 		gpmc,access-ns = <64>;
125 		gpmc,rd-cycle-ns = <82>;
126 		gpmc,wr-cycle-ns = <82>;
127 		gpmc,bus-turnaround-ns = <0>;
128 		gpmc,cycle2cycle-delay-ns = <0>;
129 		gpmc,clk-activation-ns = <0>;
130 		gpmc,wait-pin = <0>;
131 		gpmc,wr-access-ns = <40>;
132 		gpmc,wr-data-mux-bus-ns = <0>;
133 		ti,elm-id = <&elm>;
134 		ti,nand-ecc-opt = "bch8";
139 	pinctrl-names = "default", "gpio", "sleep";
140 	pinctrl-0 = <&i2c0_pins_default>;
141 	pinctrl-1 = <&i2c0_pins_gpio>;
142 	pinctrl-2 = <&i2c0_pins_sleep>;
143 	clock-frequency = <400000>;
144 	scl-gpios = <&gpio3 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
145 	sda-gpios = <&gpio3 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
152 		vcc-supply = <&vdd_mod>;
158 	clock-names = "ext-clk";
159 	system-power-controller;
163 	mdio_pins_default: mdio-default-pins {
164 		pinctrl-single,pins = <
170 	mdio_pins_sleep: mdio-sleep-pins {
171 		pinctrl-single,pins = <
177 	eth_slave1_pins_default: eth-slave1-default-pins {
178 		pinctrl-single,pins = <
194 	eth_slave1_pins_sleep: eth-slave1-sleep-pins {
195 		pinctrl-single,pins = <
211 	i2c0_pins_default: i2c0-default-pins {
212 		pinctrl-single,pins = <
218 	i2c0_pins_gpio: i2c0-gpio-pins {
219 		pinctrl-single,pins = <
225 	i2c0_pins_sleep: i2c0-sleep-pins {
226 		pinctrl-single,pins = <
232 	led_mod_pins: led-mod-pins {
233 		pinctrl-single,pins = <
238 	nand_pins_default: nand-default-pins {
239 		pinctrl-single,pins = <
258 	nand_pins_sleep: nand-sleep-pins {
259 		pinctrl-single,pins = <