dts/qcom/qcom-msm8974pro-oneplus-bacon.dts

1 // SPDX-License-Identifier: GPL-2.0
2 #include "qcom-msm8974pro.dtsi"
5 #include <dt-bindings/input/input.h>
6 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
11 	chassis-type = "handset";
12 	qcom,msm-id = <194 0x10000>;
13 	qcom,board-id = <8 0>;
20 		stdout-path = "serial0:115200n8";
23 	gpio-keys {
24 		compatible = "gpio-keys";
26 		pinctrl-0 = <&gpio_keys_default>, <&gpio_hall_sensor_default>;
27 		pinctrl-names = "default";
29 		key-volume-down {
33 			wakeup-source;
34 			debounce-interval = <15>;
37 		key-volume-up {
41 			wakeup-source;
42 			debounce-interval = <15>;
45 		event-hall-sensor {
48 			linux,input-type = <EV_SW>;
50 			linux,can-disable;
51 			debounce-interval = <150>;
59 	fuel-gauge@55 {
62 		power-supplies = <&bq24196_charger>;
69 	rmi4-i2c-dev@20 {
70 		compatible = "syna,rmi4-i2c";
73 		syna,startup-delay-ms = <100>;
75 		interrupts-extended = <&tlmm 61 IRQ_TYPE_EDGE_FALLING>;
76 		vdd-supply = <&pm8941_l22>;
77 		vio-supply = <&pm8941_lvs3>;
79 		pinctrl-names = "default";
80 		pinctrl-0 = <&touch_default_state>;
82 		#address-cells = <1>;
83 		#size-cells = <0>;
85 		rmi4-f01@1 {
87 			syna,nosleep-mode = <1>;
90 		rmi4-f12@12 {
92 			syna,sensor-type = <1>;
94 			 * Touchscreen size is 2040x1080, y-values between
95 			 * 1920-2040 are used for touchkey (menu, home & back).
99 			syna,clip-y-high = <1920>;
103 	led-controller@36 {
107 		#address-cells = <1>;
108 		#size-cells = <0>;
112 			led-sources = <0 1>;
113 			label = "lcd-backlight";
114 			default-brightness = <80>;
118 	led-controller@68 {
119 		compatible = "si-en,sn3193";
122 		shutdown-gpios = <&tlmm 45 GPIO_ACTIVE_HIGH>;
124 		#address-cells = <1>;
125 		#size-cells = <0>;
130 			led-max-microamp = <17500>;
136 			led-max-microamp = <17500>;
142 			led-max-microamp = <17500>;
153 		interrupts-extended = <&tlmm 31 IRQ_TYPE_EDGE_FALLING>;
154 		omit-battery-class;
163 	compatible = "qcom,gcc-msm8974pro-ac";
167 	qcom,rset-ohms = <800>;
168 	qcom,vset-millivolts = <3200>;
174 	gpio_keys_default: gpio-keys-active-state {
177 		input-enable;
178 		bias-disable;
179 		power-source = <PM8941_GPIO_S3>;
188 	vddmx-supply = <&pm8841_s1>;
189 	vddcx-supply = <&pm8841_s2>;
190 	vddpx-supply = <&pm8941_s3>;
192 	pinctrl-names = "default";
193 	pinctrl-0 = <&wcnss_pin_a>;
198 		vddxo-supply = <&pm8941_l6>;
199 		vddrfa-supply = <&pm8941_l11>;
200 		vddpa-supply = <&pm8941_l19>;
201 		vdddig-supply = <&pm8941_s3>;
204 	smd-edge {
205 		qcom,remote-pid = <4>;
215 	cx-supply = <&pm8841_s2>;
221 	regulators-0 {
222 		compatible = "qcom,rpm-pm8841-regulators";
225 			regulator-min-microvolt = <675000>;
226 			regulator-max-microvolt = <1050000>;
230 			regulator-min-microvolt = <875000>;
231 			regulator-max-microvolt = <1050000>;
232 			regulator-always-on;
236 			regulator-min-microvolt = <1050000>;
237 			regulator-max-microvolt = <1050000>;
241 	regulators-1 {
242 		compatible = "qcom,rpm-pm8941-regulators";
244 		vdd_l1_l3-supply = <&pm8941_s1>;
245 		vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
246 		vdd_l4_l11-supply = <&pm8941_s1>;
247 		vdd_l5_l7-supply = <&pm8941_s2>;
248 		vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
249 		vdd_l8_l16_l18_l19-supply = <&vreg_vph_pwr>;
250 		vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
251 		vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
252 		vdd_l21-supply = <&vreg_boost>;
255 			regulator-min-microvolt = <1300000>;
256 			regulator-max-microvolt = <1300000>;
258 			regulator-always-on;
259 			regulator-boot-on;
263 			regulator-min-microvolt = <2150000>;
264 			regulator-max-microvolt = <2150000>;
266 			regulator-boot-on;
270 			regulator-min-microvolt = <1800000>;
271 			regulator-max-microvolt = <1800000>;
272 			regulator-system-load = <154000>;
274 			regulator-always-on;
275 			regulator-boot-on;
276 			regulator-allow-set-load;
280 			regulator-min-microvolt = <1225000>;
281 			regulator-max-microvolt = <1225000>;
283 			regulator-always-on;
284 			regulator-boot-on;
288 			regulator-min-microvolt = <1200000>;
289 			regulator-max-microvolt = <1200000>;
293 			regulator-min-microvolt = <1225000>;
294 			regulator-max-microvolt = <1225000>;
298 			regulator-min-microvolt = <1225000>;
299 			regulator-max-microvolt = <1225000>;
303 			regulator-min-microvolt = <1800000>;
304 			regulator-max-microvolt = <1800000>;
308 			regulator-min-microvolt = <1800000>;
309 			regulator-max-microvolt = <1800000>;
311 			regulator-boot-on;
315 			regulator-min-microvolt = <1800000>;
316 			regulator-max-microvolt = <1800000>;
318 			regulator-boot-on;
322 			regulator-min-microvolt = <1800000>;
323 			regulator-max-microvolt = <1800000>;
327 			regulator-min-microvolt = <1800000>;
328 			regulator-max-microvolt = <2950000>;
332 			regulator-min-microvolt = <1800000>;
333 			regulator-max-microvolt = <2950000>;
337 			regulator-min-microvolt = <1225000>;
338 			regulator-max-microvolt = <1350000>;
342 			regulator-min-microvolt = <1800000>;
343 			regulator-max-microvolt = <1800000>;
345 			regulator-always-on;
346 			regulator-boot-on;
347 			regulator-allow-set-load;
351 			regulator-min-microvolt = <1800000>;
352 			regulator-max-microvolt = <2950000>;
354 			regulator-boot-on;
358 			regulator-min-microvolt = <1800000>;
359 			regulator-max-microvolt = <1800000>;
363 			regulator-min-microvolt = <2050000>;
364 			regulator-max-microvolt = <2050000>;
368 			regulator-min-microvolt = <2700000>;
369 			regulator-max-microvolt = <2700000>;
373 			regulator-min-microvolt = <2850000>;
374 			regulator-max-microvolt = <2850000>;
378 			regulator-min-microvolt = <2850000>;
379 			regulator-max-microvolt = <2850000>;
383 			regulator-min-microvolt = <2900000>;
384 			regulator-max-microvolt = <3350000>;
388 			regulator-min-microvolt = <2950000>;
389 			regulator-max-microvolt = <2950000>;
391 			regulator-system-load = <200000>;
392 			regulator-allow-set-load;
393 			regulator-boot-on;
397 			regulator-min-microvolt = <2950000>;
398 			regulator-max-microvolt = <2950000>;
400 			regulator-boot-on;
404 			regulator-min-microvolt = <3000000>;
405 			regulator-max-microvolt = <3000000>;
406 			regulator-allow-set-load;
410 			regulator-min-microvolt = <3000000>;
411 			regulator-max-microvolt = <3000000>;
415 			regulator-min-microvolt = <3075000>;
416 			regulator-max-microvolt = <3075000>;
418 			regulator-boot-on;
426 	vmmc-supply = <&pm8941_l20>;
427 	vqmmc-supply = <&pm8941_s3>;
429 	pinctrl-names = "default", "sleep";
430 	pinctrl-0 = <&sdc1_on>;
431 	pinctrl-1 = <&sdc1_off>;
437 	gpio_hall_sensor_default: gpio-hall-sensor-default-state {
440 		drive-strength = <8>;
441 		bias-pull-up;
444 	sdc1_on: sdc1-on-state {
445 		clk-pins {
447 			drive-strength = <4>;
448 			bias-disable;
451 		cmd-data-pins {
453 			drive-strength = <4>;
454 			bias-pull-up;
458 	touch_default_state: touch-default-state {
459 		int-pins {
462 			drive-strength = <2>;
463 			bias-disable;
466 		reset-pins {
469 			drive-strength = <2>;
470 			bias-pull-up;
474 	wcnss_pin_a: wcnss-pin-active-state {
475 		wlan-pins {
478 			drive-strength = <6>;
479 			bias-pull-down;
482 		bt-pins {
485 			drive-strength = <2>;
486 			bias-pull-down;
493 	phy-select = <&tcsr 0xb000 0>;
495 	vbus-supply = <&chg_otg>;
497 	hnp-disable;
498 	srp-disable;
499 	adp-disable;
507 	v1p8-supply = <&pm8941_l6>;
508 	v3p3-supply = <&pm8941_l24>;
511 	qcom,init-seq = /bits/ 8 <0x1 0x64>;