dts/qcom/qcom-msm8974pro-fairphone-fp2.dts

1 // SPDX-License-Identifier: GPL-2.0
2 #include "qcom-msm8974pro.dtsi"
5 #include <dt-bindings/input/input.h>
6 #include <dt-bindings/leds/common.h>
7 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
12 	chassis-type = "handset";
21 		stdout-path = "serial0:115200n8";
24 	gpio-keys {
25 		compatible = "gpio-keys";
27 		pinctrl-names = "default";
28 		pinctrl-0 = <&gpio_keys_pin_a>;
30 		key-camera-snapshot {
34 			wakeup-source;
35 			debounce-interval = <15>;
38 		key-volume-down {
42 			wakeup-source;
43 			debounce-interval = <15>;
46 		key-volume-up {
50 			wakeup-source;
51 			debounce-interval = <15>;
56 		compatible = "gpio-vibrator";
57 		enable-gpios = <&tlmm 86 GPIO_ACTIVE_HIGH>;
58 		vcc-supply = <&pm8941_l18>;
68 		interrupt-parent = <&tlmm>;
70 		reset-gpios = <&tlmm 55 GPIO_ACTIVE_LOW>;
72 		touchscreen-size-x = <1080>;
73 		touchscreen-size-y = <1920>;
82 	reboot-mode {
83 		mode-normal = <0x77665501>;
84 		mode-bootloader = <0x77665500>;
85 		mode-recovery = <0x77665502>;
90 	gpio_keys_pin_a: gpio-keys-active-state {
94 		bias-pull-up;
95 		power-source = <PM8941_GPIO_S3>;
102 	qcom,power-source = <1>;
104 	multi-led {
108 		#address-cells = <1>;
109 		#size-cells = <0>;
131 	vddmx-supply = <&pm8841_s1>;
132 	vddcx-supply = <&pm8841_s2>;
133 	vddpx-supply = <&pm8941_s3>;
135 	pinctrl-names = "default";
136 	pinctrl-0 = <&wcnss_pin_a>;
139 		vddxo-supply = <&pm8941_l6>;
140 		vddrfa-supply = <&pm8941_l11>;
141 		vddpa-supply = <&pm8941_l19>;
142 		vdddig-supply = <&pm8941_s3>;
145 	smd-edge {
146 		qcom,remote-pid = <4>;
157 	cx-supply = <&pm8841_s2>;
162 	cx-supply = <&pm8841_s2>;
163 	mss-supply = <&pm8841_s3>;
164 	mx-supply = <&pm8841_s1>;
165 	pll-supply = <&pm8941_l12>;
169 	regulators-0 {
170 		compatible = "qcom,rpm-pm8841-regulators";
173 			regulator-min-microvolt = <675000>;
174 			regulator-max-microvolt = <1050000>;
178 			regulator-min-microvolt = <500000>;
179 			regulator-max-microvolt = <1050000>;
183 			regulator-min-microvolt = <1050000>;
184 			regulator-max-microvolt = <1050000>;
188 	regulators-1 {
189 		compatible = "qcom,rpm-pm8941-regulators";
191 		vdd_l1_l3-supply = <&pm8941_s1>;
192 		vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
193 		vdd_l4_l11-supply = <&pm8941_s1>;
194 		vdd_l5_l7-supply = <&pm8941_s2>;
195 		vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
196 		vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
197 		vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
198 		vdd_l21-supply = <&vreg_boost>;
201 			regulator-min-microvolt = <1300000>;
202 			regulator-max-microvolt = <1300000>;
203 			regulator-always-on;
204 			regulator-boot-on;
208 			regulator-min-microvolt = <2150000>;
209 			regulator-max-microvolt = <2150000>;
210 			regulator-boot-on;
214 			regulator-min-microvolt = <1800000>;
215 			regulator-max-microvolt = <1800000>;
216 			regulator-always-on;
217 			regulator-boot-on;
221 			regulator-min-microvolt = <1225000>;
222 			regulator-max-microvolt = <1225000>;
223 			regulator-always-on;
224 			regulator-boot-on;
228 			regulator-min-microvolt = <1200000>;
229 			regulator-max-microvolt = <1200000>;
233 			regulator-min-microvolt = <1225000>;
234 			regulator-max-microvolt = <1225000>;
238 			regulator-min-microvolt = <1225000>;
239 			regulator-max-microvolt = <1225000>;
243 			regulator-min-microvolt = <1800000>;
244 			regulator-max-microvolt = <1800000>;
248 			regulator-min-microvolt = <1800000>;
249 			regulator-max-microvolt = <1800000>;
250 			regulator-boot-on;
254 			regulator-min-microvolt = <1800000>;
255 			regulator-max-microvolt = <1800000>;
256 			regulator-boot-on;
260 			regulator-min-microvolt = <1800000>;
261 			regulator-max-microvolt = <1800000>;
265 			regulator-min-microvolt = <1800000>;
266 			regulator-max-microvolt = <2950000>;
270 			regulator-min-microvolt = <1800000>;
271 			regulator-max-microvolt = <2950000>;
275 			regulator-min-microvolt = <1225000>;
276 			regulator-max-microvolt = <1350000>;
280 			regulator-min-microvolt = <1800000>;
281 			regulator-max-microvolt = <1800000>;
282 			regulator-always-on;
283 			regulator-boot-on;
287 			regulator-min-microvolt = <1800000>;
288 			regulator-max-microvolt = <2950000>;
289 			regulator-boot-on;
293 			regulator-min-microvolt = <1800000>;
294 			regulator-max-microvolt = <1800000>;
298 			regulator-min-microvolt = <2050000>;
299 			regulator-max-microvolt = <2050000>;
303 			regulator-min-microvolt = <2700000>;
304 			regulator-max-microvolt = <2700000>;
308 			regulator-min-microvolt = <2850000>;
309 			regulator-max-microvolt = <2850000>;
313 			regulator-min-microvolt = <2850000>;
314 			regulator-max-microvolt = <2850000>;
318 			regulator-min-microvolt = <2900000>;
319 			regulator-max-microvolt = <3350000>;
323 			regulator-min-microvolt = <2950000>;
324 			regulator-max-microvolt = <2950000>;
325 			regulator-system-load = <200000>;
326 			regulator-allow-set-load;
327 			regulator-boot-on;
331 			regulator-min-microvolt = <2950000>;
332 			regulator-max-microvolt = <2950000>;
333 			regulator-boot-on;
337 			regulator-min-microvolt = <3000000>;
338 			regulator-max-microvolt = <3300000>;
342 			regulator-min-microvolt = <3000000>;
343 			regulator-max-microvolt = <3000000>;
347 			regulator-min-microvolt = <3075000>;
348 			regulator-max-microvolt = <3075000>;
349 			regulator-boot-on;
357 	vmmc-supply = <&pm8941_l20>;
358 	vqmmc-supply = <&pm8941_s3>;
360 	pinctrl-names = "default", "sleep";
361 	pinctrl-0 = <&sdc1_on>;
362 	pinctrl-1 = <&sdc1_off>;
368 	vmmc-supply = <&pm8941_l21>;
369 	vqmmc-supply = <&pm8941_l13>;
371 	pinctrl-names = "default", "sleep";
372 	pinctrl-0 = <&sdc2_on>;
373 	pinctrl-1 = <&sdc2_off>;
377 	usb-charge-current-limit = <1500000>;
378 	qcom,fast-charge-safe-current = <1500000>;
379 	qcom,fast-charge-current-limit = <1500000>;
380 	qcom,fast-charge-safe-voltage = <4380000>;
381 	qcom,fast-charge-high-threshold-voltage = <4350000>;
382 	qcom,auto-recharge-threshold-voltage = <4240000>;
383 	qcom,minimum-input-voltage = <4450000>;
387 	sdc1_on: sdc1-on-state {
388 		clk-pins {
390 			drive-strength = <16>;
391 			bias-disable;
394 		cmd-data-pins {
396 			drive-strength = <10>;
397 			bias-pull-up;
401 	sdc2_on: sdc2-on-state {
402 		clk-pins {
404 			drive-strength = <10>;
405 			bias-disable;
408 		cmd-data-pins {
410 			drive-strength = <6>;
411 			bias-pull-up;
415 	wcnss_pin_a: wcnss-pin-active-state {
416 		wlan-pins {
420 			drive-strength = <6>;
421 			bias-pull-down;
424 		bt-pins {
428 			drive-strength = <2>;
429 			bias-pull-down;
432 		fm-pins {
436 			drive-strength = <2>;
437 			bias-pull-down;
446 	phy-select = <&tcsr 0xb000 0>;
448 	vbus-supply = <&chg_otg>;
450 	hnp-disable;
451 	srp-disable;
452 	adp-disable;
458 	v1p8-supply = <&pm8941_l6>;
459 	v3p3-supply = <&pm8941_l24>;
462 	qcom,init-seq = /bits/ 8 <0x1 0x64>;