Lines Matching +full:0 +full:x260
57 (0 = disable debug prints, 1 = normal debug messages,
71 Default: 0
80 the card #0. Similarly, when ``adsp_map=0``, /dev/adsp will be mapped
81 to PCM #0 of the card #0.
83 commas, such like ``dsp_map=0,1``.
98 Default: 0
119 Values: 0 through 31 or negative;
142 appearing card. They can do it by specifying "index=1,0" module
158 the port must be specified. For actual AdLib FM cards it will be 0x388.
170 64:0 OPL2 FM synth OPL2 FM Port
175 sbiload -p 64:0 std.sb drums.sb
181 aplaymidi -p 64:0 foo.mid
189 Clock frequency for AD1816A chip (default = 0, 33000Hz)
203 DMA # for AD1848 chip (0,1,3)
261 0 = disabled (default), 1 = auto-detect
291 (-2 = Force probing, -1 = Default behavior, 0-2 = Use the
324 0 = Disable all workarounds,
325 1 = Force the PCI latency of the Aureal card to 0xff,
351 port # for BASE (0x220,0x240,0x260,0x280)
353 port # for WSS (0x530,0x604,0xe80,0xf40)
357 DMA # for WSS playback (0,1,3)
359 DMA # for WSS capture (0,1), -1 = disabled (default)
361 port # for MPU-401 UART (0x300,0x330), -1 = disabled (default)
365 port # for OPL3 (0x388), -1 = disabled (default)
371 ``port`` needs to match the BASE ADDRESS jumper on the card (0x220 or 0x240)
377 full-duplex mode. When ``dma1=3``, only ``dma2=0`` is valid and the only way to
378 enable capture since only channels 0 and 1 are available for capture.
380 Generic settings are ``port=0x220 wss_port=0x530 irq=10 dma1=1 dma2=0
381 mpu_port=0x330 mpu_irq=9 fm_port=0x388``.
393 port # for BASE (0x220,0x240,0x260,0x280)
395 port # for WSS (0x530,0x604,0xe80,0xf40)
399 DMA # for WSS playback (0,1,3)
401 DMA # for WSS capture (0,1), -1 = disabled (default)
403 port # for MPU-401 UART (0x300,0x330), -1 = disabled (default)
407 port # for OPL3 (0x388), -1 = disabled (default)
413 ``port`` needs to match the BASE ADDRESS jumper on the card (0x220 or 0x240)
419 full-duplex mode. When ``dma1=3``, only ``dma2=0`` is valid and the only way to
420 enable capture since only channels 0 and 1 are available for capture.
422 Generic settings are ``port=0x220 wss_port=0x530 irq=10 dma1=1 dma2=0
423 mpu_port=0x330 mpu_irq=9 fm_port=0x388``.
483 ISA PnP detection - 0 = disable, 1 = enable (default)
485 with ``isapnp=0``, the following options are available:
519 0x300,0x310,0x320,0x330 = legacy port,
521 0 = disable
524 0x388 = legacy port,
526 0 = disable
530 Joystick port address (0 = disable, 1 = auto-detect)
566 ISA PnP detection - 0 = disable, 1 = enable (default)
568 with ``isapnp=0``, the following options are available:
571 port # for CS4236 chip (PnP setup - 0x534)
573 control port # for CS4236 chip (PnP setup - 0x120,0x210,0xf00)
575 port # for MPU-401 UART (PnP setup - 0x300), -1 = disable
577 FM port # for CS4236 chip (PnP setup - 0x388), -1 = disable
583 first DMA # for CS4236 chip (0,1,3)
585 second DMA # for CS4236 chip (0,1,3), -1 = disable
602 Secondary codec ID (0 = disable, default)
619 Support OSS mmap mode (default = 0).
705 Use hrtimer (=1, default) or system timer (=0)
711 * 0 = interleaved with mmap support
719 the read/ written buffer data to be consistent, pass fake_buffer=0
760 * Creative Card wo/Digital out [0x0003/0x1f03]
761 * Creative Card w/Digital out [0x0003/0x1f0f]
762 * Creative Card w/Digital CD in [0x000f/0x1f0f]
763 * Creative Card wo/Digital out + LiveDrive [0x3fc3/0x1fc3]
764 * Creative Card w/Digital out + LiveDrive [0x3fc3/0x1fcf]
765 * Creative Card w/Digital CD in + LiveDrive [0x3fcf/0x1fcf]
766 * Creative Card wo/Digital out + Digital I/O 2 [0x0fc3/0x1f0f]
767 * Creative Card w/Digital out + Digital I/O 2 [0x0fc3/0x1f0f]
768 * Creative Card w/Digital CD in + Digital I/O 2 [0x0fcf/0x1f0f]
769 * Creative Card 5.1/w Digital out + LiveDrive [0x3fc3/0x1fff]
770 * Creative Card 5.1 (c) 2003 [0x3fc3/0x7cff]
771 * Creative Card all ins and outs [0x3fff/0x7fff]
807 port # for joystick (0x200,0x208,0x210,0x218), 0 = disable
820 ISA PnP detection - 0 = disable, 1 = enable (default)
822 port # for MPU-401 port (0x300,0x310,0x320,0x330), -1 = disable (default)
828 with ``isapnp=0``, the following additional options are available:
831 port # for ES-1688 chip (0x220,0x240,0x260)
835 DMA # for ES-1688 chip (0,1,3)
846 ISA PnP detection - 0 = disable, 1 = enable (default)
848 with ``isapnp=0``, the following options are available:
851 port # for ES-18xx chip (0x220,0x240,0x260)
853 port # for MPU-401 port (0x300,0x310,0x320,0x330), -1 = disable (default)
859 first DMA # for ES-18xx chip (0,1,3)
861 first DMA # for ES-18xx chip (0,1,3)
888 capture channels (1-8, default=0)
890 clock (0 = auto-detection)
892 support the power-management (0 = off, 1 = on, 2 = auto (default))
894 enable MPU401 (0 = off, 1 = on, 2 = auto (default))
913 example: 0x10002 (MediaForte 256-PCPR, device 1)
941 port # for GF1 chip (0x220,0x230,0x240,0x250,0x260)
949 0 to 31, (0.59V-4.52V or 0.389V-2.98V)
963 port # for ES-1688 chip (0x220,0x230,0x240,0x250,0x260)
965 port # for GF1 chip (0x210,0x220,0x230,0x240,0x250,0x260,0x270)
967 port # for MPU-401 port (0x300,0x310,0x320,0x330), -1 = disable
975 DMA # for ES-1688 chip (0,1,3)
979 0 to 31, (0.59V-4.52V or 0.389V-2.98V)
993 port # for GF1 chip (0x220,0x230,0x240,0x250,0x260)
1001 0 to 31, (0.59V-4.52V or 0.389V-2.98V)
1023 0 = auto: falls back to LPIB when POSBUF doesn't work,
1032 When the bit 8 (0x100) is set, the lower 8 bits are used
1048 Selects the beep registration mode (0=off, 1=on);
1059 Automatic power-saving timeout (in second, 0 = disable)
1304 AC'97 codec clock base (0 = auto-detect)
1316 controller chip (0 = off, 1 = on, -1 = default)
1342 AC'97 codec clock base (0 = auto-detect)
1358 0 to 31, (0.59V-4.52V or 0.389V-2.98V)
1360 1 = MIDI UART enable, 0 = MIDI UART disable (default)
1364 1 = InterWave effects enable (default 0); requires 8 voices
1366 ISA PnP detection - 0 = disable, 1 = enable (default)
1368 with ``isapnp=0``, the following options are available:
1371 port # for InterWave chip (0x210,0x220,0x230,0x240,0x250,0x260)
1375 DMA # for InterWave chip (0,1,3,5,6,7)
1377 DMA # for InterWave chip (0,1,3,5,6,7,-1=disable)
1389 0 to 31, (0.59V-4.52V or 0.389V-2.98V)
1391 1 = MIDI UART enable, 0 = MIDI UART disable (default)
1395 1 = InterWave effects enable (default 0); requires 8 voices
1397 ISA PnP detection - 0 = disable, 1 = enable (default)
1399 with ``isapnp=0``, the following options are available:
1402 port # for InterWave chip (0x210,0x220,0x230,0x240,0x250,0x260)
1404 tone control (i2c bus) port # for TEA6330T chip (0x350,0x360,0x370,0x380)
1408 DMA # for InterWave chip (0,1,3,5,6,7)
1410 DMA # for InterWave chip (0,1,3,5,6,7,-1=disable)
1421 port # for SB DSP chip (0x210,0x220,0x230,0x240,0x250,0x260)
1429 MPU-401 port # (0x300,0x310,0x320,0x330)
1480 GPIO pin number for external amp (0-15) or -1 for default pin (8
1488 For example, a Panasonic notebook might need ``amp_gpio=0x0d``
1508 Port # (0x530,0x604,0xe80,0xf40)
1512 1st dma # (0,1,3)
1514 2nd dma # (0,1)
1516 MPU-401 port # (0x300,0x310,0x320,0x330)
1520 FM Port # (0x388)
1559 PnP detection - 0 = disable, 1 = enable (default)
1574 Memory address (0xb0000, 0xc8000, 0xd0000, 0xd8000, 0xe0000 or 0xe8000)
1578 calibrate signal (default = 0)
1580 ISA PnP detection - 0 = disable, 1 = enable (default)
1582 Digital daughterboard present (default = 0)
1584 Config port (0x250, 0x260 or 0x270) default = PnP
1592 IDE port #0
1619 Memory address (0xb0000, 0xc8000, 0xd0000, 0xd8000, 0xe0000 or 0xe8000)
1623 calibrate signal (default = 0)
1625 ISA PnP detection - 0 = disable, 1 = enable (default)
1637 I/O port # for MTPAV (0x378,0x278, default=0x378)
1663 0 or 1 (disabled by default)
1667 0 or 1 (disabled by default)
1669 alias buffer_top=0x25a800
1684 Sony F250: buffer_top=0x25a800
1685 Sony F270: buffer_top=0x272800
1696 but some doesn't have ISA PnP. You'll need to specify ``isapnp=0``
1723 ISA PnP detection - 0 = disable, 1 = enable (default)
1725 with ``isapnp=0``, the following options are available:
1728 control port # for OPL3-SA chip (0x370)
1730 SB port # for OPL3-SA chip (0x220,0x240)
1732 WSS port # for OPL3-SA chip (0x530,0xe80,0xf40,0x604)
1734 port # for MPU-401 UART (0x300,0x330), -1 = disable
1736 FM port # for OPL3-SA chip (0x388), -1 = disable
1740 first DMA # for Yamaha OPL3-SA chip (0,1,3)
1742 second DMA # for Yamaha OPL3-SA chip (0,1,3), -1 = disable
1756 ISA PnP detection - 0 = disable, 1 = enable (default)
1758 with ``isapnp=0``, the following options are available:
1761 port # for WSS chip (0x530,0xe80,0xf40,0x604)
1763 port # for MPU-401 UART (0x300,0x310,0x320,0x330)
1765 port # for OPL3 device (0x388)
1771 first DMA # for WSS chip (0,1,3)
1781 ISA PnP detection - 0 = disable, 1 = enable (default)
1783 with ``isapnp=0``, the following options are available:
1786 port # for WSS chip (0x530,0xe80,0xf40,0x604)
1788 port # for MPU-401 UART (0x300,0x310,0x320,0x330)
1790 port # for OPL3 device (0x388)
1796 first DMA # for WSS chip (0,1,3)
1798 second DMA # for WSS chip (0,1,3)
1808 ISA PnP detection - 0 = disable, 1 = enable (default)
1810 with ``isapnp=0``, the following options are available:
1813 port # for WSS chip (0x530,0xe80,0xf40,0x604)
1815 port # for MPU-401 UART (0x300,0x310,0x320,0x330)
1817 port # for OPL3 device (0x388)
1823 first DMA # for WSS chip (0,1,3)
1825 second DMA # for WSS chip (0,1,3)
1906 Joystick port # (default: 0x200)
1908 MPU401 port # (default: 0x330)
1910 OPL3 port # (default: 0x388)
1938 Enable precise pointer (doesn't work reliably). (default = 0)
1966 port # for SB DSP chip (0x220,0x240,0x260)
1983 Mic Auto-Gain-Control - 0 = disable, 1 = enable (default)
1985 ASP/CSP chip support - 0 = disable (default), 1 = enable
1987 ISA PnP detection - 0 = disable, 1 = enable (default)
1989 with isapnp=0, the following options are available:
1992 port # for SB DSP 4.x chip (0x220,0x240,0x260)
1994 port # for MPU-401 UART (0x300,0x330), -1 = disable
1996 base port # for EMU8000 synthesizer (0x620,0x640,0x660) (snd-sbawe
2001 8-bit DMA # for SB DSP 4.x chip (0,1,3)
2022 Port # (0x220 or 0x240)
2024 MSS Port # (0x530 or 0xe80)
2028 MPU-401 IRQ # (5,7,9,10) ,0 - no MPU-401 irq
2030 DMA # (1,3,0)
2032 Enable gameport - 0 = disable (default), 1 = enable
2056 Enable gameport - 0 = disable (default), 1 = enable
2092 ISA PnP detection - 0 = disable, 1 = enable (default)
2094 with isapnp=0, the following options are available:
2172 Reverb Enable - 1 = enable, 0 = disable (default);
2175 Mic Gain Enable - 1 = enable, 0 = disable (default)
2199 0 = Soundcanvas, 1 = MS-124T, 2 = MS-124W S/A,
2250 Default: 0x0000
2288 * bit 0: Skip reading sample rate for devices
2354 0x300,0x310,0x320,0x330, otherwise obtain BIOS setup
2361 support DXS channels, 0 = auto (default), 1 = enable, 2 = disable,
2381 As default (``dxs_support = 0``), 48k fixed rate is chosen
2449 Capture IBL size. (default = 0, minimum size)
2469 The size is usually aligned to 126. As default (=0), the smallest
2481 Capture IBL size. (default = 0, minimum size)
2510 0x300,0x330,0x332,0x334, 0 (disable) by default,
2513 0x388,0x398,0x3a0,0x3a8, 0 (disable) by default
2516 0x201,0x202,0x204,0x205, 0 (disable) by default,
2567 For backward compatibility, the corresponding integer value -1, 0, ...
2580 For probing the non ISA-PnP cards, you have to pass ``isapnp=0`` option
2603 alias snd-card-0 snd-emu10k1
2604 alias sound-slot-0 snd-emu10k1
2622 alias snd-card-0 snd-interwave
2624 options snd-interwave index=0
2627 alias sound-slot-0 snd-interwave
2632 (index 0) and ens1371 as the second (index 1).
2641 Then, the first slot (#0) is reserved for snd-interwave driver, and
2722 echo "squake 0 0 disable" > /proc/asound/card0/pcm0c/oss
2723 echo "rvplayer 0 0 block" > /proc/asound/card0/pcm0p/oss
2743 integer numbers (0x prefix is needed for the hex).
2744 MASK is the PCI DMA mask. Pass 0 if not restricted.
2748 than 0. The max number is 4.