Lines Matching full:it
13 * It provides a nice large console (128 cols + 48 lines with 1024x768)
24 How to use it?
93 XF{68,86}_FBDev should work just fine, but it is non-accelerated. On non-intel
108 Driver contains SVGALib compatibility code. It is turned on by choosing textual
109 mode for console. You can do it at boot time by using videomode
112 Switching to another console and back fixes it. I hope that it is SVGALib's
127 it always probe for memory. Default is to use whole detected
132 configuration, you can override it by this (you cannot override
133 `off`). It is default.
134 noaccel do not use acceleration engine. It does not work on Alphas.
135 accel use acceleration engine. It is default.
139 It is default.
140 nopciretry disable PCI retries. It is needed for some broken chipsets,
141 it is autodetected for intel's 82437. In this case device does
142 not comply to PCI 2.1 specs (it will not guarantee that every
144 pciretry enable PCI retries. It is default, except for intel's 82437.
145 novga disables VGA I/O ports. It is default if BIOS did not enable
148 vga preserve state of VGA I/O ports. It is default. Driver does not
149 enable VGA I/O if BIOS did not it (it is not safe to enable it in
151 nobios disables BIOS ROM. It is default if BIOS did not enable BIOS
154 bios preserve state of BIOS ROM. It is default. Driver does not enable
157 it if you have G100 and/or if driver cannot detect memory, you see
159 are still initialized. It is default.
160 init driver initializes every device it knows about.
190 mtrr enables write combining on frame buffer. It speeds up video
191 accesses much. It is default. You must have MTRR support enabled
193 sgram tells to driver that you have Gxx0 with SGRAM memory. It has no
196 It is a default.
200 noinv24 use standard timings. It is the default.
202 noinverse show true colors on screen. It is default.
208 hwcursor enables hardware cursor. It is default. If you are using
213 blink enables cursor blinking. It is default.
214 nofastfont disables fastfont feature. It is default.
216 font data, it must be >= (fontwidth*fontheight*chars_in_font)/8.
217 It is faster on Gx00 series, but slower on older cards.
218 grayscale enable grayscale summing. It works in PSEUDOCOLOR modes (text,
219 4bpp, 8bpp). In DIRECTCOLOR modes it is limited to characters
222 nograyscale disable grayscale summing. It is default.
223 cross4MB enables that pixel line can cross 4MB boundary. It is default for
225 nocross4MB pixel line must not cross 4MB boundary. It is default for
258 can modify it with these options:
317 - interlaced text mode is not supported; it looks like hardware limitation,
333 set frequency higher that this. It causes sparks, black holes and other
336 (and it works with 8bpp on about 320 MHz dotclocks (and changed mclk)).
338 them (maybe that chip overheats, but it has a very big cooler (G100 has
339 none), so it should work).
343 - feature connector of Mystique and Gx00 is set to VGA mode (it is disabled
346 - some check for input values are not so strict how it should be (you can
352 - 4bpp is available only on Millennium I and Millennium II. It is hardware
358 instead of one of 16M colors). It is due to hardware limitation of
364 It is time to redraw whole screen 1000 times in 1024x768, 60Hz. It is
366 (for 32bpp it is about 3GB of data (exactly 3000 MB); for 8x16 font in
369 faster, it is kernel-space only time on P-II/350 MHz, Millennium I in 33 MHz
401 * Yes, it is slower than Millennium I.
407 + secondary head shares videomemory with primary head. It is not problem
418 to change it to TV mode. Also, you must select at least 525 lines for
421 + if you compiled it as module, you must insert i2c-matroxfb, matroxfb_maven
428 + secondary head shares videomemory with primary head. It is not problem
438 + if you compiled it as module, you must insert matroxfb_g450 and matroxfb_crtc2