arm/marvell/cp110-system-controller.txt

6 giving access to numerous features: clocks, pin-muxing and many other
11  - compatible: must be: "syscon", "simple-mfd";
12  - reg: register area of the CP110 system controller
18 -------
23  - a set of core clocks
24  - a set of gateable clocks
28  - The first cell must be 0 or 1. 0 for the core clocks and 1 for the
30  - The second cell identifies the particular core clock or gateable
34  - Core clocks
35    - 0 0	APLL
36    - 0 1	PPv2 core
37    - 0 2	EIP
38    - 0 3	Core
39    - 0 4	NAND core
40    - 0 5	SDIO core
41  - Gateable clocks
42    - 1 0	Audio
43    - 1 1	Comm Unit
44    - 1 2	NAND
45    - 1 3	PPv2
46    - 1 4	SDIO
47    - 1 5	MG Domain
48    - 1 6	MG Core
49    - 1 7	XOR1
50    - 1 8	XOR0
51    - 1 9	GOP DP
52    - 1 11	PCIe x1 0
53    - 1 12	PCIe x1 1
54    - 1 13	PCIe x4
55    - 1 14	PCIe / XOR
56    - 1 15	SATA
57    - 1 16	SATA USB
58    - 1 17	Main
59    - 1 18	SD/MMC/GOP
60    - 1 21	Slow IO (SPI, NOR, BootROM, I2C, UART)
61    - 1 22	USB3H0
62    - 1 23	USB3H1
63    - 1 24	USB3 Device
64    - 1 25	EIP150
65    - 1 26	EIP197
69  - compatible: must be:
70      "marvell,cp110-clock"
71  - #clock-cells: must be set to 2
74 --------
77 Documentation/devicetree/bindings/pinctrl/marvell,mvebu-pinctrl.txt.
81 - compatible: "marvell,armada-7k-pinctrl", "marvell,armada-8k-cpm-pinctrl",
82   "marvell,armada-8k-cps-pinctrl" or "marvell,cp115-standalone-pinctrl"
85 Available mpp pins/groups and functions:
89 name	pins	functions
95 mpp4	4	gpio, dev(ad13), au(i2sbclk), ge0(rxctl), tdm(rstn), mss_uart(rxd), uart1(cts), pcie0(clkreq…
96 mpp5	5	gpio, dev(ad12), au(i2sdi), ge0(rxclk), tdm(intn), mss_uart(txd), uart1(rts), pcie1(clkreq),…
97 mpp6	6	gpio, dev(ad11), ge0(txd3), spi0(csn2), au(i2sextclk), sata1(present_act), pcie2(clkreq), ua…
119 mpp28	28	gpio, dev(csn1), spi1(csn0), mss_gpio5, ge0(rxd2), spi0(csn5), pcie2(clkreq), ptp(pulse), …
120 mpp29	29	gpio, dev(csn2), spi1(mosi), mss_gpio6, ge0(rxd1), spi0(csn6), pcie1(clkreq), ptp(clk), ms…
121 mpp30	30	gpio, dev(csn3), spi1(clk), mss_gpio7, ge0(rxd0), spi0(csn7), pcie0(clkreq), ptp(pclk_out)…
123 …mss_spi(miso), tdm(drx), au(i2sextclk), au(i2sdi), ge(mdio), sdio(v18_en), pcie1(clkreq), mss_gpio0
124 …io(pwr10), mss_spi(csn), tdm(fsync), au(i2smclk), sdio(bus_pwr), xg(mdio), pcie2(clkreq), mss_gpio1
125 …(pwr11), mss_spi(mosi), tdm(dtx), au(i2slrclk), sdio(wr_protect), ge(mdc), pcie0(clkreq), mss_gpio2
127 … ptp(clk), synce1(clk), au(i2sbclk), sata0(present_act), xg(mdc), ge(mdc), pcie2(clkreq), mss_gpio5
128 …t), tdm(intn), mss_i2c(sck), sata1(present_act), ge(mdc), xg(mdc), pcie1(clkreq), mss_gpio6, link(…
140 mpp49	49	gpio, ge1(txclkout), mii(crs), spi1(miso), uart1(rxd), ge(mdio), pcie0(clkreq), sdio(v18_e…
143 …ge1(rxd1), synce1(clk), synce2(clk), spi1(csn2), uart1(cts), led(clk), pcie(rstoutn), pcie0(clkreq)
156 -----
159 Documentation/devicetree/bindings/gpio/gpio-mvebu.yaml.
163 - compatible: "marvell,armada-8k-gpio"
165 - offset: offset address inside the syscon block
169 CP110_LABEL(syscon0): system-controller@440000 {
170 	compatible = "syscon", "simple-mfd";
174 		compatible = "marvell,cp110-clock";
175 		#clock-cells = <2>;
179 		compatible = "marvell,armada-8k-cpm-pinctrl";
183 		compatible = "marvell,armada-8k-gpio";
186 		gpio-controller;
187 		#gpio-cells = <2>;
188 		gpio-ranges = <&CP110_LABEL(pinctrl) 0 0 32>;
197 --------
203 critical point to any subnode of the thermal-zone node.
209 - compatible: must be one of:
210   * marvell,armada-cp110-thermal
211 - reg: register range associated with the thermal functions.
214 - interrupts-extended: overheat interrupt handle. Should point to
215   a line of the ICU-SEI irqchip (116 is what is usually used by the
216   firmware). The ICU-SEI will redirect towards interrupt line #37 of the
218   See interrupt-controller/interrupts.txt
219 - #thermal-sensor-cells: shall be <1> when thermal-zones subnodes refer
224 CP110_LABEL(syscon1): system-controller@6f8000 {
225 	compatible = "syscon", "simple-mfd";
228 	CP110_LABEL(thermal): thermal-sensor@70 {
229 		compatible = "marvell,armada-cp110-thermal";
231 		interrupts-extended = <&CP110_LABEL(icu_sei) 116 IRQ_TYPE_LEVEL_HIGH>;
232 		#thermal-sensor-cells = <1>;