Merge git://git.denx.de/u-boot-tegra

Merge tag 'xilinx-for-v2018.07' of git://www.denx.de/git/u-boot-microblaze

Xilinx changes for v2018.07

microblaze:
- Align defconfig

zynq:
- Rework fpga initializat

Merge tag 'xilinx-for-v2018.07' of git://www.denx.de/git/u-boot-microblaze

Xilinx changes for v2018.07

microblaze:
- Align defconfig

zynq:
- Rework fpga initialization and cpuinfo handling

zynqmp:
- Add ZynqMP R5 support
- Wire and enable watchdog on zcu100-revC
- Setup MMU map for DDR at run time
- Show board info based on DT and cleanup IDENT_STRING

zynqmp tools:
- Add read partition support
- Add initial support for Xilinx bif format for boot.bin generation

mmc:
- Fix get_timer usage on 64bit cpus
- Add support for SD3.0 UHS mode

nand-zynq:
- Add support for 16bit buswidth
- Use address cycles from onfi params

scsi:
- convert ceva sata to UCLASS_AHCI

timer:
- Add Cadence TTC for ZynqMP r5

watchdog:
- Minor cadence driver cleanup

show more ...

arm: zynqmp: Add ZynqMP minimal R5 support

Xilinx ZynqMP also contains dual Cortex R5 which can run U-Boot.
This patch is adding minimal support to get U-Boot boot.
U-Boot on R5 runs

arm: zynqmp: Add ZynqMP minimal R5 support

Xilinx ZynqMP also contains dual Cortex R5 which can run U-Boot.
This patch is adding minimal support to get U-Boot boot.
U-Boot on R5 runs out of DDR with default configuration that's why
DDR needs to be partitioned if there is something else running on arm64.
Console is done via Cadence uart driver and the first Cadence Triple
Timer Counter is used for time.

This configuration with uart1 was tested on zcu100-revC.

U-Boot 2018.05-rc2-00021-gd058a08d907d (Apr 18 2018 - 14:11:27 +0200)

Model: Xilinx ZynqMP R5
DRAM: 512 MiB
WARNING: Caches not enabled
MMC:
In: serial@ff010000
Out: serial@ff010000
Err: serial@ff010000
Net: Net Initialization Skipped
No ethernet found.
ZynqMP r5>

There are two ways how to run this on ZynqMP.
1. Run from ZynqMP arm64
tftpb 20000000 u-boot-r5.elf
setenv autostart no && bootelf -p 20000000
cpu 4 disable && cpu 4 release 10000000 lockstep
or
cpu 4 disable && cpu 4 release 10000000 split

2. Load via jtag when directly to R5

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

show more ...

Merge git://git.denx.de/u-boot-imx

Merge git://git.denx.de/u-boot-sunxi

serial: Migrate CONFIG_FSL_LINFLEXUART to Kconfig

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>

Merge git://git.denx.de/u-boot-imx

Signed-off-by: Tom Rini <trini@konsulko.com>

Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot

Patch queue for efi - 2018-04-09

Highlights this time around:

- Lots of minor spec compliance fixes
- S

Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot

Patch queue for efi - 2018-04-09

Highlights this time around:

- Lots of minor spec compliance fixes
- Support full range of GOP BLT commands
- More fine grained error checking
- Network fixes (init, DP)
- Lots of other bug fixes...

show more ...

powerpc: mpc8xx: Change CONFIG_8xx to CONFIG_MPC8xx

CONFIG_8xx doesn't mean much outside of arch/powerpc/
This patch renames it CONFIG_MPC8xx just like CONFIG_MPC85xx etc ...
It also

powerpc: mpc8xx: Change CONFIG_8xx to CONFIG_MPC8xx

CONFIG_8xx doesn't mean much outside of arch/powerpc/
This patch renames it CONFIG_MPC8xx just like CONFIG_MPC85xx etc ...
It also renames 8xx_immap.h to immap_8xx.h to be consistent with
other file names.

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>

show more ...

Merge git://git.denx.de/u-boot-sunxi

Signed-off-by: Tom Rini <trini@konsulko.com>

Merge git://git.denx.de/u-boot-fsl-qoriq

Merge git://git.denx.de/u-boot-usb

Merge git://git.denx.de/u-boot-sunxi

arm: stm32: add new architecture for STM32MP family

- add new arch stm32mp for STM32 MPU/Soc based on Cortex A
- support for stm32mp157 SOC
- SPL is used as first boot stage loader

arm: stm32: add new architecture for STM32MP family

- add new arch stm32mp for STM32 MPU/Soc based on Cortex A
- support for stm32mp157 SOC
- SPL is used as first boot stage loader
- using driver model for all the drivers, even in SPL
- all security feature are deactivated (ETZC and TZC)
- reused STM32 MCU drivers when it is possible

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>

show more ...

Convert all of CONFIG_CONS_INDEX to Kconfig

This converts the following to Kconfig:
CONFIG_CONS_INDEX

We have existing entries for this option in a number of places, with

Convert all of CONFIG_CONS_INDEX to Kconfig

This converts the following to Kconfig:
CONFIG_CONS_INDEX

We have existing entries for this option in a number of places, with
different guards on them. They're also sometimes used for things not
directly inside of the serial driver. First, introduce a new symbol to
guard the use of CONFIG_CONS_INDEX, so that in the case where we don't
need this for the serial driver, but for some other use, we can still do
it. Next, consolidate all of these into the single entry in
drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that
we can imply a correct value here to make the defconfig side of this
smaller.

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rework a lot of the logic here, such that I took authorship from
Adam, but kept his S-o-B line]
Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

Merge tag 'xilinx-for-v2018.03' of git://git.denx.de/u-boot-microblaze

Xilinx changes for v2018.03

- Several Kconfig fixes (also moving configs to defconfigs)
- Some DTS updates

Merge tag 'xilinx-for-v2018.03' of git://git.denx.de/u-boot-microblaze

Xilinx changes for v2018.03

- Several Kconfig fixes (also moving configs to defconfigs)
- Some DTS updates
- ZynqMP psu rework based on Zynq concept
- Add low level initialization for zc770 and zcu102
- Add support for Zynq zc770 x16 nand configuration
- Add mini nand/emmc ZynqMP targets
- Some arasan nand changes

show more ...

serial: Make full device search optional

Commit 608b0c4ad4e5ec0c ("serial: Use next serial device if probing fails")
added code to search for more serial devices if the default one was n

serial: Make full device search optional

Commit 608b0c4ad4e5ec0c ("serial: Use next serial device if probing fails")
added code to search for more serial devices if the default one was not
probed correctly.

Unfortunately, that breaks omap3_evm. So while investigating why that is
the case, let's disable the full search for everyone but bcm283x where it
is needed.

Fixes: 608b0c4ad4e5ec0c ("serial: Use next serial device if probing fails")
Reported-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>

show more ...

Merge git://git.denx.de/u-boot-rockchip

bcm2835_pl011_serial: Add BCM2835 specific serial driver

On bcm2835 we need to ensure we only access serial devices that are
muxed to the serial output pins of the pin header. To achieve

bcm2835_pl011_serial: Add BCM2835 specific serial driver

On bcm2835 we need to ensure we only access serial devices that are
muxed to the serial output pins of the pin header. To achieve this
for the pl011 device, add a bcm2835 specific pl011 wrapper device
that does this check but otherwise behaves like a pl011 device.

Signed-off-by: Alexander Graf <agraf@suse.de>

show more ...

bcm2835_mu_serial: Convert to Kconfig

Setting config options using headers is deprecated. This patch converts
the BCM2835 Mini-UART to Kconfig.

Signed-off-by: Alexander Graf <ag

bcm2835_mu_serial: Convert to Kconfig

Setting config options using headers is deprecated. This patch converts
the BCM2835 Mini-UART to Kconfig.

Signed-off-by: Alexander Graf <agraf@suse.de>

show more ...

pl01x: Convert CONFIG_PL01X_SERIAL to Kconfig

We want to use Kconfig logic to depend on whether pl01x devices
are built in, so let's convert their inclusion selection to Kconfig.

pl01x: Convert CONFIG_PL01X_SERIAL to Kconfig

We want to use Kconfig logic to depend on whether pl01x devices
are built in, so let's convert their inclusion selection to Kconfig.

This round goes to pl01x.

Signed-off-by: Alexander Graf <agraf@suse.de>

show more ...

pl011: Convert CONFIG_PL011_SERIAL to Kconfig

We want to use Kconfig logic to depend on whether pl01x devices
are built in, so let's convert their inclusion selection to Kconfig.

pl011: Convert CONFIG_PL011_SERIAL to Kconfig

We want to use Kconfig logic to depend on whether pl01x devices
are built in, so let's convert their inclusion selection to Kconfig.

This round goes to pl011.

Signed-off-by: Alexander Graf <agraf@suse.de>

show more ...

pl010: Convert CONFIG_PL010_SERIAL to Kconfig

We want to use Kconfig logic to depend on whether pl01x devices
are built in, so let's convert their inclusion selection to Kconfig.

pl010: Convert CONFIG_PL010_SERIAL to Kconfig

We want to use Kconfig logic to depend on whether pl01x devices
are built in, so let's convert their inclusion selection to Kconfig.

This round goes to pl010.

Signed-off-by: Alexander Graf <agraf@suse.de>

show more ...

Merge git://git.denx.de/u-boot-spi

Merge git://git.denx.de/u-boot-marvell