Merge branch 'master' of git://www.denx.de/git/u-boot-cfi-flash

Merge branch 'u-boot/master' into u-boot-arm/master

Merge branch 'master' of git://git.denx.de/u-boot-nds32

Merge branch 'master' of git://git.denx.de/u-boot-i2c

The sandburst-specific i2c drivers have been deleted, conflict was just
over the SPDX conversion.

Conflicts:
bo

Merge branch 'master' of git://git.denx.de/u-boot-i2c

The sandburst-specific i2c drivers have been deleted, conflict was just
over the SPDX conversion.

Conflicts:
board/sandburst/common/ppc440gx_i2c.c
board/sandburst/common/ppc440gx_i2c.h

Signed-off-by: Tom Rini <trini@ti.com>

show more ...

Add GPL-2.0+ SPDX-License-Identifier to source files

Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>

drivers/net/smc911x.c: Fix GCC 4.6 warning

smc911x.c: In function 'smc911x_initialize':
smc911x.c:288:12: warning: assignment from incompatible pointer type
[enabled by default]

drivers/net/smc911x.c: Fix GCC 4.6 warning

smc911x.c: In function 'smc911x_initialize':
smc911x.c:288:12: warning: assignment from incompatible pointer type
[enabled by default]

Signed-off-by: Anatolij Gustschin <agust@denx.de>

show more ...

consolidate mdelay by providing a common function for all users

There are several mdelay() definitions in the driver and
board code. Remove them all and provide a common mdelay()
in

consolidate mdelay by providing a common function for all users

There are several mdelay() definitions in the driver and
board code. Remove them all and provide a common mdelay()
in lib/time.c.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx

* 'master' of git://git.denx.de/u-boot-mpc85xx:
powerpc/mpc8610hpcd: set pci1_hose.config_table after fsl_setup_hose
pow

Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx

* 'master' of git://git.denx.de/u-boot-mpc85xx:
powerpc/mpc8610hpcd: set pci1_hose.config_table after fsl_setup_hose
powerpc/mpc8548cds: set pci1_hose.config_table after fsl_setup_hose
powerpc/mpc8568mds: set pci1_hose.config_table after fsl_setup_hose

show more ...

smc911x: Fix build warnings

Commit 6af1d41 "smc911x MII made available" was missing a few "const"
qualifiers. Fix the resulting in build warnings:

smc911x.c: In function 'smc91

smc911x: Fix build warnings

Commit 6af1d41 "smc911x MII made available" was missing a few "const"
qualifiers. Fix the resulting in build warnings:

smc911x.c: In function 'smc911x_initialize':
smc911x.c:297: warning: passing argument 2 of 'miiphy_register' from incompatible pointer type
smc911x.c:297: warning: passing argument 3 of 'miiphy_register' from incompatible pointer type

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Helmut Raiger <helmut.raiger@hale.at>

show more ...

smc911x MII made available

The driver already had the MII functions, but they have not been
registered using miiphy_register().

Signed-off-by: Helmut Raiger <helmut.raiger@hale.

smc911x MII made available

The driver already had the MII functions, but they have not been
registered using miiphy_register().

Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>

show more ...

miiphy: convert to linux/mii.h

The include/miiphy.h header duplicates a lot of things from linux/mii.h.
So punt all the things that overlap to keep the API simple and to make
merging

miiphy: convert to linux/mii.h

The include/miiphy.h header duplicates a lot of things from linux/mii.h.
So punt all the things that overlap to keep the API simple and to make
merging between U-Boot and Linux simpler.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-ubi

Merge branch 'master' of git://git.denx.de/u-boot-imx

lan91c96, smc911x: remove useless free(ptr) calls on NULL ptr

Signed-off-by: Serge Ziryukin <ftrvxmtrx@gmail.com>

Merge branch 'master' of git://git.denx.de/u-boot-net

smc911x driver frame alignment patch

SMSC911x chips have alignment function to allow frame payload data
(which comes after 14-bytes ethernet header) to be aligned at some
boundary wh

smc911x driver frame alignment patch

SMSC911x chips have alignment function to allow frame payload data
(which comes after 14-bytes ethernet header) to be aligned at some
boundary when reading it from fifo (usually - 4 bytes boundary).
This is done by inserting fake zeros bytes BEFORE actual frame data when
reading from SMSC's fifo.
This function controlled by RX_CFG register. There are bits that
represents amount of fake bytes to be inserted.

Linux uses alignment of 4 bytes. Ethernet frame header is 14 bytes long,
so we need to add 2 fake bytes to get payload data aligned at 4-bytes
boundary.
Linux driver does this by adding IP_ALIGNMENT constant (defined at
skb.h) when calculating fifo data length. All network subsystem of Linux
uses this constant too when calculating different offsets.

But u-boot does not use any packet data alignment, so we don't need to
add anything when calculating fifo data length.
Moreover, driver zeros the RX_CFG register just one line up, so chip
does not insert any fake data at the beginig. So calculated data length
is always bigger by 1 word.

It seems that at almost every packet read we get an underflow condition
at fifo and possible corruption of data. Especially at continuous
transfers, such as tftp.

Just after removing this magic addition, I've got tftp transfer speed as
it aught to be at 100Mbps. It was really slow before.

It seems that fifo underflow occurs only when using byte packing on
32-bit blackfin bus (may be because of very small delay between reads).

Signed-off-by: Valentin Yakovenkov <yakovenkov@niistt.ru>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx

Merge branch 'master' of git://git.denx.de/u-boot-cfi-flash

Merge branch 'master' of git://git.denx.de/u-boot-net

NET: Fix MAC addr handling for smc911x

This patch turns off MAC address mismatch warning when
optional eeprom programmed with MAC address is not available.
In that case, smc911x's MA

NET: Fix MAC addr handling for smc911x

This patch turns off MAC address mismatch warning when
optional eeprom programmed with MAC address is not available.
In that case, smc911x's MAC address register has its default
value ff:ff:ff:ff:ff:ff and it's not a valid address. This
makes eth_initialize() show the warning which has no
meaningful information while environment variable ethaddr
overrides the address read from the register. If there's no
eeprom and the value of MAC address register is not valid
after initialization, dev->enetaddr had better not be updated
and maintain its initial value 00:00:00:00:00:00, which I
think is what eth_initialize() expects. This is not a bug fix.
Even without this patch, the driver works fine. It's just for
enhancing the way of displaying messages.

Signed-off-by: Seunghyeon Rhee <seunghyeon@lpmtec.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>

show more ...

Merge branch 'master' into next

Conflicts:
lib_generic/zlib.c

Signed-off-by: Wolfgang Denk <wd@denx.de>

smc911x: fix typo in smc911x_handle_mac_address name

Signed-off-by: Mike Rapoport <mike@compulab.co.il>

Merge branch 'master' into next

Merge branch 'master' of git://git.denx.de/u-boot-net

smc911x: make smc911x_initialize return correct value

Make smc911x_initialize return -1 on error and number of interfaces
detected otherwise.

Signed-off-by: Mike Rapoport <mike@

smc911x: make smc911x_initialize return correct value

Make smc911x_initialize return -1 on error and number of interfaces
detected otherwise.

Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>

show more ...