Merge branch 'master' of git://git.denx.de/u-boot-spi

dm: MIGRATION: Update migration plan for SPI

- v2019.04 for no dm conversion drivers
- v2019.07 for partially converted drivers.

Note: there were many updates on this deadline, so better
not update

dm: MIGRATION: Update migration plan for SPI

- v2019.04 for no dm conversion drivers
- v2019.07 for partially converted drivers.

Note: there were many updates on this deadline, so better
not update this again.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

show more ...

Merge tag 'u-boot-imx-20190101' of git://www.denx.de/git/u-boot-imx

imx for 2019.01

- introduce support for i.MX8M
- fix size limit for Vhybrid / pico boards
- several board fixes
- w1 driver for M

Merge tag 'u-boot-imx-20190101' of git://www.denx.de/git/u-boot-imx

imx for 2019.01

- introduce support for i.MX8M
- fix size limit for Vhybrid / pico boards
- several board fixes
- w1 driver for MX2x / MX5x

show more ...

doc: imx: fix typos in mxsimage.txt

This fixes two small typos in mxsimage.txt.

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Reviewed-by: Breno Lima <breno.lima@nxp.com>

doc: imx: fix typo in imximage.txt

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Reviewed-by: Breno Lima <breno.lima@nxp.com>

w1: Add driver for i.MX bus master controller

Two variants of controllers are supported:
V1 (bitwise only) found in
i.MX21, i.MX27, i.MX31, i.MX51
V2 (byte operations) found in
i.MX25, i.MX35, i.M

w1: Add driver for i.MX bus master controller

Two variants of controllers are supported:
V1 (bitwise only) found in
i.MX21, i.MX27, i.MX31, i.MX51
V2 (byte operations) found in
i.MX25, i.MX35, i.MX50, i.MX53

Only tested on i.MX53 hardware but in both modes
(by modifying the device tree).

Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>

show more ...

video: Add information about using TrueType fonts

U-Boot supports using TrueType fonts on the console, which is useful for
presenting a nice UI to users, e.g. for system recovery.

Add information a

video: Add information about using TrueType fonts

U-Boot supports using TrueType fonts on the console, which is useful for
presenting a nice UI to users, e.g. for system recovery.

Add information about how to compile this on ARM platforms, since this is
not obvious.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

show more ...

doc: README.commands: sub-commands

Describe the implementation of sub-commands.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>

odroid: Update README.odroid for support of Odroid HC1

updated READM.odroid for supported Odroid HC1 development board.

Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Lukasz Majewsk

odroid: Update README.odroid for support of Odroid HC1

updated READM.odroid for supported Odroid HC1 development board.

Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

show more ...

doc: README.ae350: Sync for ax25-ae350 rename

Rename ax25-ae350 as ae350_rv[32|64] for 32 or 64 bit.

Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Reviewe

doc: README.ae350: Sync for ax25-ae350 rename

Rename ax25-ae350 as ae350_rv[32|64] for 32 or 64 bit.

Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

show more ...

blk: Rework guard around part_init call

The function part_init() will only be built when we have both
CONFIG_PARTITIONS and CONFIG_HAVE_BLOCK_DEVICE set. Protect the call to
this function with both

blk: Rework guard around part_init call

The function part_init() will only be built when we have both
CONFIG_PARTITIONS and CONFIG_HAVE_BLOCK_DEVICE set. Protect the call to
this function with both of these tests now.

Cc: Simon Glass <sjg@chromium.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Cc: Mingkai Hu <mingkai.hu@nxp.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: Vanessa Maegima <vanessa.maegima@nxp.com>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Adam Ford <aford173@gmail.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

show more ...

qemu-arm: Add persistent environment support

Currently on qemu-arm platforms environment is kept in RAM. Instead
use pflash device 1 to provide persistent environment support across
device reset.

A

qemu-arm: Add persistent environment support

Currently on qemu-arm platforms environment is kept in RAM. Instead
use pflash device 1 to provide persistent environment support across
device reset.

Also (optionally) provide support for persistent environment across
qemu machine OFF/ON using following instructions:

- Create envstore.img using qemu-img:
qemu-img create -f raw envstore.img 64M
- Add a pflash drive parameter to the command line:
-drive if=pflash,format=raw,index=1,file=envstore.img

Signed-off-by: Sumit Garg <sumit.garg@linaro.org>

show more ...

Merge tag 'for-master-20181210' of git://git.denx.de/u-boot-rockchip

Improvements:
- init DRAM for RK322x in SPL
- add FAN53555 PMIC/regulator driver
- update MicroCrystal RV3029 driver to Kconfig a

Merge tag 'for-master-20181210' of git://git.denx.de/u-boot-rockchip

Improvements:
- init DRAM for RK322x in SPL
- add FAN53555 PMIC/regulator driver
- update MicroCrystal RV3029 driver to Kconfig and sync from Linux
- add bootcount uclass and first DM-driver for bootcount

show more ...

power: add FAN53555 family support

This adds a driver for the FAN53555 family of regulators and wraps it
in a PMIC implementation.

While these devices support a 'normal' and 'suspend' mode (control

power: add FAN53555 family support

This adds a driver for the FAN53555 family of regulators and wraps it
in a PMIC implementation.

While these devices support a 'normal' and 'suspend' mode (controlled
via an external pin) to switch between two programmable voltages, this
incarnation of the driver assumes that the device is always operating
in 'normal' mode.

Only setting/reading the programmed voltage is supported at this time
and the following device functionality remains unsupported:
- switching the selected voltage (via a GPIO)
- disabling the voltage output via software-control
This matches the functionality of the Linux driver.

Tested on a RK3399-Q7 (with 'option 5' devices): setting voltages from
the U-Boot shell and verifying output voltages on the board.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>

show more ...

bootcount: add uclass for bootcount

The original bootcount methods do not provide an interface to DM and
rely on a static configuration for I2C devices (e.g. bus, chip-addr,
etc. are configured thro

bootcount: add uclass for bootcount

The original bootcount methods do not provide an interface to DM and
rely on a static configuration for I2C devices (e.g. bus, chip-addr,
etc. are configured through defines statically). On a modern system
that exposes multiple devices in a DTS-configurable way, this is less
than optimal and a interface to DM-based devices will be desirable.

This adds a simple driver that is DM-aware and configurable via DTS.
If ambiguous (i.e. multiple bootcount-devices are present) the
/chosen/u-boot,bootcount-device property can be used to select one
bootcount device.

Initially, this provides support for the following DM devices:
* RTC devices

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>

show more ...

lib: fdtdec: Add function re-setup the fdt more effeciently

In some cases it may be useful to be able to change the fdt we have been
using and use another one instead. For example, the TI platforms

lib: fdtdec: Add function re-setup the fdt more effeciently

In some cases it may be useful to be able to change the fdt we have been
using and use another one instead. For example, the TI platforms uses an
EEPROM to store board information and, based on the type of board,
different dtbs are used by the SPL. When DM_I2C is used, a first dtb must
be used before the I2C is initialized and only then the final dtb can be
selected.
To speed up the process and reduce memory usage, introduce a new function
fdtdec_setup_best_match() that re-use the DTBs loaded in memory by
fdtdec_setup() to select the best match.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Heiko Schocher <hs@denx.de>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-spi

- Various MTD fixes from Boris
- Zap various unused / legacy paths.
- pxa3xx NAND update from Miquel

Signed-off-by: Tom Rini <trini@konsulko.co

Merge branch 'master' of git://git.denx.de/u-boot-spi

- Various MTD fixes from Boris
- Zap various unused / legacy paths.
- pxa3xx NAND update from Miquel

Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

dm: MIGRATION: Update migration plan for BLK

The biggest part of migration to using CONFIG_BLK is that we need to
have the various subsystems migrated first, so reword the plan here to
reference the

dm: MIGRATION: Update migration plan for BLK

The biggest part of migration to using CONFIG_BLK is that we need to
have the various subsystems migrated first, so reword the plan here to
reference the new deadlines.

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

dm: MIGRATION: Add migration plan for CONFIG_SATA

As the core of the subsystem has been converted along with some of the
drivers, formalize a deadline for migration.

Cc: Akshay Bhat <akshaybhat@tim

dm: MIGRATION: Add migration plan for CONFIG_SATA

As the core of the subsystem has been converted along with some of the
drivers, formalize a deadline for migration.

Cc: Akshay Bhat <akshaybhat@timesys.com>
Cc: Andreas Geisreiter <ageisreiter@dh-electronics.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jason Liu <jason.hui.liu@nxp.com>
Cc: Ken Lin <Ken.Lin@advantech.com.tw>
Cc: Ludwig Zenz <lzenz@dh-electronics.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Soeren Moch <smoch@web.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

dm: MIGRATION: Add migration plan for DM_USB

As much of the USB system has been migrated to DM now, formalize a
deadline for migration.

Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon G

dm: MIGRATION: Add migration plan for DM_USB

As much of the USB system has been migrated to DM now, formalize a
deadline for migration.

Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

dm: MIGRATION: Add migration plan for DM_MMC

Given that at this point the MMC subsystem itself has been migrated
along with a number of subsystem drivers, formalize a deadline for
migration.

Review

dm: MIGRATION: Add migration plan for DM_MMC

Given that at this point the MMC subsystem itself has been migrated
along with a number of subsystem drivers, formalize a deadline for
migration.

Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

show more ...

Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot

Patch queue for efi - 2018-12-03

This release is fully packed with lots of glorious improvements in UEFI
land again!

- Make PE images

Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot

Patch queue for efi - 2018-12-03

This release is fully packed with lots of glorious improvements in UEFI
land again!

- Make PE images more standards compliant
- Improve sandbox support
- Improve correctness
- Fix RISC-V execution on virt model
- Honor board defined top of ram (fixes a few boards)
- Imply DM USB access when distro boot is available
- Code cleanups

show more ...

doc: uImage.FIT: signature.txt: add option padding

Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

doc: README.iscsi: Open-iSCSI configuration

Provide settings for Open-iSCSI

Reformat headers. h3-headers marked with ^^^ are not recognized in some
markup editors. Use the ### notation instead.

Si

doc: README.iscsi: Open-iSCSI configuration

Provide settings for Open-iSCSI

Reformat headers. h3-headers marked with ^^^ are not recognized in some
markup editors. Use the ### notation instead.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-socfpga