| #
b48b69ba |
| 15-Jun-2015 |
Tom Rini <trini@konsulko.com> |
Merge git://git.denx.de/u-boot-marvell
|
| #
27d170af |
| 04-Jun-2015 |
Nishanth Menon <nm@ti.com> |
ARM: DRA7-evm: Add mux data
Adding the mux data, manual and virtual mode
settings for DRA7-evm.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokesh
ARM: DRA7-evm: Add mux data
Adding the mux data, manual and virtual mode
settings for DRA7-evm.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
show more ...
|
| #
bd5053ff |
| 14-Jan-2015 |
Tom Rini <trini@ti.com> |
Merge branch 'buildman' of git://git.denx.de/u-boot-x86
Conflicts:
tools/buildman/control.py
Signed-off-by: Tom Rini <trini@ti.com>
|
| #
3bfbf32b |
| 16-Dec-2014 |
Tom Rini <trini@ti.com> |
Merge branch 'master' of git://git.denx.de/u-boot-socfpga
|
| #
fc9b0b80 |
| 11-Dec-2014 |
Tom Rini <trini@ti.com> |
Merge branch 'master' of git://git.denx.de/u-boot-usb
Conflicts:
board/freescale/mx6sxsabresd/mx6sxsabresd.c
Signed-off-by: Tom Rini <trini@ti.com>
|
| #
9b416a9f |
| 10-Dec-2014 |
Tom Rini <trini@ti.com> |
Merge branch 'master' of git://www.denx.de/git/u-boot-imx
|
| #
d51aae64 |
| 10-Dec-2014 |
Tom Rini <trini@ti.com> |
Merge branch 'rmobile' of git://git.denx.de/u-boot-sh
|
| #
272a1acf |
| 08-Dec-2014 |
Tom Rini <trini@ti.com> |
Merge git://git.denx.de/u-boot-mpc85xx
|
| #
98d2d5e8 |
| 08-Dec-2014 |
Tom Rini <trini@ti.com> |
Merge branch 'master' of git://git.denx.de/u-boot-ti
|
| #
ae525189 |
| 10-Nov-2014 |
Lubomir Popov <lpopov@mm-sol.com> |
ARM: OMAP5: DRA7xx: Fix misleading comments in mux_data.h
The comments on the QSPI pad assignments erronously swapped
the qspi1_d0 and qspi1_d1 functionality and could cause
confusio
ARM: OMAP5: DRA7xx: Fix misleading comments in mux_data.h
The comments on the QSPI pad assignments erronously swapped
the qspi1_d0 and qspi1_d1 functionality and could cause
confusion. QSPI1_D[0] is in fact muxed on pad U1 (gpmc_a16),
and QSPI1_D[1] - on pad P3 (gpmc_a17). Fixing comments.
Signed-off-by: Lubomir Popov <l-popov@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
show more ...
|
| #
2c19478e |
| 02-Sep-2014 |
Tom Rini <trini@ti.com> |
Merge branch 'master' of git://git.denx.de/u-boot-arc
|
| #
6defdc0b |
| 29-Aug-2014 |
Tom Rini <trini@ti.com> |
Merge branch 'master' of git://git.denx.de/u-boot-ti
|
| #
7b922523 |
| 04-Aug-2014 |
Lokesh Vutla <lokeshvutla@ti.com> |
ARM: DRA: Enable VTT regulator
DRA7 evm REV G and later boards uses a vtt regulator for DDR3 termination
and this is controlled by gpio7_11. Configuring gpio7_11.
The pad A22(offset
ARM: DRA: Enable VTT regulator
DRA7 evm REV G and later boards uses a vtt regulator for DDR3 termination
and this is controlled by gpio7_11. Configuring gpio7_11.
The pad A22(offset 0x3b4) is used by gpio7_11 on REV G and later boards,
and left unused on previous boards, so it is safe enough to enable gpio
on all DRA7 boards.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
show more ...
|
| #
9352697a |
| 22-Jul-2014 |
pekon gupta <pekon@ti.com> |
board/ti/dra7xx: add support for parallel NOR
This patch adds support for parallel NOR device (S29GL512S10) present on J6-EVM.
The Flash device is connected to GPMC controller on chip-se
board/ti/dra7xx: add support for parallel NOR
This patch adds support for parallel NOR device (S29GL512S10) present on J6-EVM.
The Flash device is connected to GPMC controller on chip-select[0] and accessed
as memory-mapped device. It has data-witdh=x16, capacity-64MBytes(512Mbits) and
is CFI compatible.
As multiple devices are share GPMC pins on this board, so following board
settings are required to detect NOR device:
SW5.1 (NAND_BOOTn) = OFF (logic-1)
SW5.2 (NOR_BOOTn) = ON (logic-0) /* Active-low */
SW5.3 (eMMC_BOOTn) = OFF (logic-1)
SW5.4 (QSPI_BOOTn) = OFF (logic-1)
And also set appropriate SYSBOOT configurations:
SW3.1 (SYSBOOT[ 8])= ON (logic-1) /* selects SYS_CLK1 speed */
SW3.2 (SYSBOOT[ 9])= OFF (logic-0) /* selects SYS_CLK1 speed */
SW3.3 (SYSBOOT[10])= ON (logic-1) /* wait-pin monitoring = enabled */
SW3.4 (SYSBOOT[11])= OFF (logic-0) /* device type: Non Muxed */
SW3.5 (SYSBOOT[12])= OFF (logic-0) /* device type: Non Muxed */
SW3.6 (SYSBOOT[13])= ON (logic-1) /* device bus-width: 1(x16) */
SW3.7 (SYSBOOT[14])= OFF (logic-0) /* reserved */
SW3.8 (SYSBOOT[15])= ON (logic-1) /* reserved */
Also, following changes are required to enable NOR Flash support in
dra7xx_evm board profile:
show more ...
|
| #
54a97d28 |
| 22-Jul-2014 |
pekon gupta <pekon@ti.com> |
board/ti/dra7xx: add support for parallel NAND
This patch adds support for x16 NAND device (MT29F2G16AAD) connected to GPMC
chip-select[0] on DRA7xx EVM.
As GPMC pins are shared by m
board/ti/dra7xx: add support for parallel NAND
This patch adds support for x16 NAND device (MT29F2G16AAD) connected to GPMC
chip-select[0] on DRA7xx EVM.
As GPMC pins are shared by multiple devices, so in addition to this patch
following board settings are required for NAND device detection [1]:
SW5.9 (GPMC_WPN) = OFF (logic-1)
SW5.1 (NAND_BOOTn) = ON (logic-0) /* Active-low */
SW5.2 (NOR_BOOTn) = OFF (logic-1)
SW5.3 (eMMC_BOOTn) = OFF (logic-1)
SW5.4 (QSPI_BOOTn) = OFF (logic-1)
And also set appropriate SYSBOOT configurations
SW2.1 (SYSBOOT[0]) = ON (logic-1) /* selects NAND Boot */
SW2.2 (SYSBOOT[1]) = OFF (logic-0) /* selects NAND Boot */
SW2.3 (SYSBOOT[2]) = OFF (logic-0) /* selects NAND Boot */
SW2.4 (SYSBOOT[3]) = OFF (logic-0) /* selects NAND Boot */
SW2.5 (SYSBOOT[4]) = ON (logic-1) /* selects NAND Boot */
SW2.6 (SYSBOOT[5]) = ON (logic-1) /* selects NAND Boot */
SW2.7 (SYSBOOT[6]) = OFF (logic-0) /* reserved */
SW2.8 (SYSBOOT[7]) = OFF (logic-0) /* reserved */
SW3.1 (SYSBOOT[ 8])= ON (logic-1) /* selects SYS_CLK1 speed */
SW3.2 (SYSBOOT[ 9])= OFF (logic-0) /* selects SYS_CLK1 speed */
SW3.3 (SYSBOOT[10])= ON (logic-1) /* wait-pin monitoring = enabled */
SW3.4 (SYSBOOT[11])= OFF (logic-0) /* device type: Addr/Data Muxed */
SW3.5 (SYSBOOT[12])= ON (logic-1) /* device type: Addr/Data Muxed */
SW3.6 (SYSBOOT[13])= ON (logic-1) /* device bus-width: 1(x16) */
SW3.7 (SYSBOOT[14])= OFF (logic-0) /* reserved */
SW3.8 (SYSBOOT[15])= ON (logic-1) /* reserved */
Following changes are required in board.cfg to enable NAND on J6-EVM:
show more ...
|
| #
c23154aa |
| 08-Aug-2014 |
Stefano Babic <sbabic@denx.de> |
Merge branch 'master' of git://git.denx.de/u-boot-arm
|
| #
dcdb61a0 |
| 04-Aug-2014 |
Tom Rini <trini@ti.com> |
Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx
|
| #
362f16b1 |
| 29-Jul-2014 |
Tom Rini <trini@ti.com> |
Merge branch 'master' of git://git.denx.de/u-boot-arm
|
| #
b1cdd8ba |
| 28-Jul-2014 |
Albert ARIBAUD <albert.u.boot@aribaud.net> |
Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'
|
| #
48b3ed21 |
| 28-Jul-2014 |
Albert ARIBAUD <albert.u.boot@aribaud.net> |
Merge branch 'u-boot-sh/rmobile' into 'u-boot-arm/master'
|
| #
740f41d3 |
| 28-Jul-2014 |
Albert ARIBAUD <albert.u.boot@aribaud.net> |
Merge branch 'u-boot-sunxi/master' into 'u-boot-arm/master'
|
| #
e5ff845b |
| 22-May-2014 |
Mugunthan V N <mugunthanvnm@ti.com> |
ARM: DRA7xx: Add cpsw second port pinmux
Add cpsw second slave port pinmux to use it as primary ethernet port
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
|
| #
dab5e346 |
| 16-Jul-2014 |
Stefano Babic <sbabic@denx.de> |
Merge branch 'master' of git://git.denx.de/u-boot
Signed-off-by: Stefano Babic <sbabic@denx.de>
Conflicts:
boards.cfg
|
| #
84f24ac8 |
| 11-Jul-2014 |
Tom Rini <trini@ti.com> |
Merge branch 'master' of git://www.denx.de/git/u-boot-imx
|
| #
22692ec0 |
| 09-Jul-2014 |
Tom Rini <trini@ti.com> |
Merge branch 'master' of git://www.denx.de/git/u-boot-imx
|