Merge branch 'master' of git://git.denx.de/u-boot-video

Merge branch 'master' of git://git.denx.de/u-boot-spi

Merge git://git.denx.de/u-boot-dm

Merge git://git.denx.de/u-boot-marvell

ARM: DRA72-evm: Update mux and VIRTUAL/MANUAL mode timings

All the mux configurations needs to be done as part of the IODelay
sequence to avoid glitch. Adding all the mux configuration,

ARM: DRA72-evm: Update mux and VIRTUAL/MANUAL mode timings

All the mux configurations needs to be done as part of the IODelay
sequence to avoid glitch. Adding all the mux configuration, MANUAL/VIRTUAL
mode configuration as needed for DRA72-evm.

Also update the mux for SD card detect on DRA74-evm.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

Merge branch 'master' of git://www.denx.de/git/u-boot-imx

ARM : DRA7: Switch QSPI to use MODE-0 at 64MHz

According to Data Manual(SPRS915P) of AM572x, TI QSPI controller on
DRA74 EVM(rev 1.1+) can support up to 64MHz in MODE-0, whereas MODE-3 i

ARM : DRA7: Switch QSPI to use MODE-0 at 64MHz

According to Data Manual(SPRS915P) of AM572x, TI QSPI controller on
DRA74 EVM(rev 1.1+) can support up to 64MHz in MODE-0, whereas MODE-3 is
limited to 48MHz. Hence, switch to MODE-0 for better throughput.
Also, add IODelay parameters for the same.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

Merge branch 'master' of git://www.denx.de/git/u-boot-imx

Merge branch 'master' of git://www.denx.de/git/u-boot-imx

Merge branch 'master' of git://git.denx.de/u-boot-video

Merge branch 'master' of http://git.denx.de/u-boot-sunxi

ARM: dra7x/am57x: Remove pin input/output config from WAKEUP pins

The WAKEUP_X pins are always an input no matter the pinmux mode.
However, the 18th bit that typical configures a pin as

ARM: dra7x/am57x: Remove pin input/output config from WAKEUP pins

The WAKEUP_X pins are always an input no matter the pinmux mode.
However, the 18th bit that typical configures a pin as an input is
considered reserved for the WAKEUP_X pins. Therefore, for any WAKEUP
pin remove any configuration that sets that pin as an input. Since
those pins are only inputs remove any output configuration from those
pins.

Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-video

ARM: DRA74-evm: Add iodelay values for SR2.0

Silicon revision 2.0 has new signal routing hence has an updated set of
iodelay parameters to be used. Update the configuration for the same.

ARM: DRA74-evm: Add iodelay values for SR2.0

Silicon revision 2.0 has new signal routing hence has an updated set of
iodelay parameters to be used. Update the configuration for the same.
Padmux remains the same.

Based on data from VayuES2_EVM_Base_Config-20150807.

NOTE: With respect to the RGMII values, the Manual IODelay values
are used for the fine adjusments needed to meet the tight RGMII
specification.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot

Merge branch 'master' of git://git.denx.de/u-boot-spi

Merge git://git.denx.de/u-boot-samsung

Merge git://git.denx.de/u-boot-marvell

Merge branch 'master' of git://git.denx.de/u-boot

ARM: DRA7-evm: prevent DCAN1 _wait_target_disable failure in kernel

If board is booted with transitions happening on DCAN1 pins then
the following warning is seen in the kernel at boot w

ARM: DRA7-evm: prevent DCAN1 _wait_target_disable failure in kernel

If board is booted with transitions happening on DCAN1 pins then
the following warning is seen in the kernel at boot when the
hwmod layer initializes.

"omap_hwmod: dcan1: _wait_target_disable failed"

This is because DCAN1 module's SWAKEUP mechanism is broken
and it fails to correctly turn OFF if it sees a transition on the
DCAN1 pins. Suggested workaround is to keep DCAN1 pins in safe mode
while enabling/disabling DCAN1 module.

The hwmod layer enables and disables all modules at boot
and we have no opportunity to put the DCAN1 pins in safe mode
at that point.

DCAN1 is not used by u-boot so it doesn't matter to it if these
pins are in safe mode. The kernel driver correctly configures
the right mode when DCAN1 is active.

Signed-off-by: Roger Quadros <rogerq@ti.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-mips

ARM: DRA72x: fix io delay calibration for ethernet

we currently use in-development IODelay values for DRA72x which are
proposed in the data sheet, however, DRA72x EVM uses DP83865 ethern

ARM: DRA72x: fix io delay calibration for ethernet

we currently use in-development IODelay values for DRA72x which are
proposed in the data sheet, however, DRA72x EVM uses DP83865 ethernet
Phy over RGMII. The PHY characteristics and routing choices made on
the EVM, make the current iodelay values fail ethernet communication.

Instead, we need to choose custom values for DRA72x-evm specifically
designed for the PHY and routing on the platform for ethernet to
function.

Cc: Nishanth Menon <nm@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>

show more ...

Merge branch 'u-boot/master' into 'u-boot-arm/master'

Merge branch 'master' of git://www.denx.de/git/u-boot-imx

Conflicts:
configs/tbs2910_defconfig
configs/tqma6q_mba6_mmc_defconfig
configs/tqma6q_mba6_spi_d

Merge branch 'master' of git://www.denx.de/git/u-boot-imx

Conflicts:
configs/tbs2910_defconfig
configs/tqma6q_mba6_mmc_defconfig
configs/tqma6q_mba6_spi_defconfig
configs/tqma6s_mba6_mmc_defconfig
configs/tqma6s_mba6_spi_defconfig
include/configs/mx6_common.h

Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

Merge git://git.denx.de/u-boot-usb