target/riscv: mmu changes for zicfiss shadow stack protection

zicfiss protects shadow stack using new page table encodings PTE.W=1,
PTE.R=0 and PTE.X=0. This encoding is reserved if zicfiss is not
i

target/riscv: mmu changes for zicfiss shadow stack protection

zicfiss protects shadow stack using new page table encodings PTE.W=1,
PTE.R=0 and PTE.X=0. This encoding is reserved if zicfiss is not
implemented or if shadow stack are not enabled.
Loads on shadow stack memory are allowed while stores to shadow stack
memory leads to access faults. Shadow stack accesses to RO memory
leads to store page fault.

To implement special nature of shadow stack memory where only selected
stores (shadow stack stores from sspush) have to be allowed while rest
of regular stores disallowed, new MMU TLB index is created for shadow
stack.

Furthermore, `check_zicbom_access` (`cbo.clean/flush/inval`) may probe
shadow stack memory and must always raise store/AMO access fault because
it has store semantics. For non-shadow stack memory even though
`cbo.clean/flush/inval` have store semantics, it will not fault if read
is allowed (probably to follow `clflush` on x86). Although if read is not
allowed, eventually `probe_write` will do store page (or access) fault (if
permissions don't allow it). cbo operations on shadow stack memory must
always raise store access fault. Thus extending `get_physical_address` to
recieve `probe` parameter as well.

Signed-off-by: Deepak Gupta <debug@rivosinc.com>
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20241008225010.1861630-14-debug@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>

show more ...

target/riscv: tb flag for shadow stack instructions

Shadow stack instructions can be decoded as zimop / zcmop or shadow stack
instructions depending on whether shadow stack are enabled at current
pr

target/riscv: tb flag for shadow stack instructions

Shadow stack instructions can be decoded as zimop / zcmop or shadow stack
instructions depending on whether shadow stack are enabled at current
privilege. This requires a TB flag so that correct TB generation and correct
TB lookup happens. `DisasContext` gets a field indicating whether bcfi is
enabled or not.

Signed-off-by: Deepak Gupta <debug@rivosinc.com>
Co-developed-by: Jim Shu <jim.shu@sifive.com>
Co-developed-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20241008225010.1861630-13-debug@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>

show more ...

target/riscv: introduce ssp and enabling controls for zicfiss

zicfiss introduces a new state ssp ("shadow stack register") in cpu.
ssp is expressed as a new unprivileged csr (CSR_SSP=0x11) and holds

target/riscv: introduce ssp and enabling controls for zicfiss

zicfiss introduces a new state ssp ("shadow stack register") in cpu.
ssp is expressed as a new unprivileged csr (CSR_SSP=0x11) and holds
virtual address for shadow stack as programmed by software.

Shadow stack (for each mode) is enabled via bit3 in *envcfg CSRs.
Shadow stack can be enabled for a mode only if it's higher privileged
mode had it enabled for itself. M mode doesn't need enabling control,
it's always available if extension is available on cpu.

This patch also implements helper bcfi function which determines if bcfi
is enabled at current privilege or not.

Adds ssp to migration state as well.

Signed-off-by: Deepak Gupta <debug@rivosinc.com>
Co-developed-by: Jim Shu <jim.shu@sifive.com>
Co-developed-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20241008225010.1861630-12-debug@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>

show more ...

target/riscv: Add zicfiss extension

zicfiss [1] riscv cpu extension enables backward control flow integrity.

This patch sets up space for zicfiss extension in cpuconfig. And imple-
ments dependency

target/riscv: Add zicfiss extension

zicfiss [1] riscv cpu extension enables backward control flow integrity.

This patch sets up space for zicfiss extension in cpuconfig. And imple-
ments dependency on A, zicsr, zimop and zcmop extensions.

[1] - https://github.com/riscv/riscv-cfi

Signed-off-by: Deepak Gupta <debug@rivosinc.com>
Co-developed-by: Jim Shu <jim.shu@sifive.com>
Co-developed-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20241008225010.1861630-11-debug@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>

show more ...

target/riscv: Expose zicfilp extension as a cpu property

Signed-off-by: Deepak Gupta <debug@rivosinc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20241008225010.1861630

target/riscv: Expose zicfilp extension as a cpu property

Signed-off-by: Deepak Gupta <debug@rivosinc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20241008225010.1861630-10-debug@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>

show more ...

target/riscv: zicfilp `lpad` impl and branch tracking

Implements setting lp expected when `jalr` is encountered and implements
`lpad` instruction of zicfilp. `lpad` instruction is taken out of
auipc

target/riscv: zicfilp `lpad` impl and branch tracking

Implements setting lp expected when `jalr` is encountered and implements
`lpad` instruction of zicfilp. `lpad` instruction is taken out of
auipc x0, <imm_20>. This is an existing HINTNOP space. If `lpad` is
target of an indirect branch, cpu checks for 20 bit value in x7 upper
with 20 bit value embedded in `lpad`. If they don't match, cpu raises a
sw check exception with tval = 2.

Signed-off-by: Deepak Gupta <debug@rivosinc.com>
Co-developed-by: Jim Shu <jim.shu@sifive.com>
Co-developed-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20241008225010.1861630-8-debug@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>

show more ...

target/riscv: tracking indirect branches (fcfi) for zicfilp

zicfilp protects forward control flow (if enabled) by enforcing all
indirect call and jmp must land on a landing pad instruction `lpad`. I

target/riscv: tracking indirect branches (fcfi) for zicfilp

zicfilp protects forward control flow (if enabled) by enforcing all
indirect call and jmp must land on a landing pad instruction `lpad`. If
target of an indirect call or jmp is not `lpad` then cpu/hart must raise
a sw check exception with tval = 2.

This patch implements the mechanism using TCG. Target architecture branch
instruction must define the end of a TB. Using this property, during
translation of branch instruction, TB flag = FCFI_LP_EXPECTED can be set.
Translation of target TB can check if FCFI_LP_EXPECTED flag is set and a
flag (fcfi_lp_expected) can be set in DisasContext. If `lpad` gets
translated, fcfi_lp_expected flag in DisasContext can be cleared. Else
it'll fault.

Signed-off-by: Deepak Gupta <debug@rivosinc.com>
Co-developed-by: Jim Shu <jim.shu@sifive.com>
Co-developed-by: Andy Chiu <andy.chiu@sifive.com>
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20241008225010.1861630-7-debug@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>

show more ...

target/riscv: additional code information for sw check

sw check exception support was recently added. This patch further augments
sw check exception by providing support for additional code which is

target/riscv: additional code information for sw check

sw check exception support was recently added. This patch further augments
sw check exception by providing support for additional code which is
provided in *tval. Adds `sw_check_code` field in cpuarchstate. Whenever
sw check exception is raised *tval gets the value deposited in
`sw_check_code`.

Signed-off-by: Deepak Gupta <debug@rivosinc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20241008225010.1861630-6-debug@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>

show more ...

target/riscv: save and restore elp state on priv transitions

elp state is recorded in *status on trap entry (less privilege to higher
privilege) and restored in elp from *status on trap exit (higher

target/riscv: save and restore elp state on priv transitions

elp state is recorded in *status on trap entry (less privilege to higher
privilege) and restored in elp from *status on trap exit (higher to less
privilege).

Additionally this patch introduces a forward cfi helper function to
determine if current privilege has forward cfi is enabled or not based on
*envcfg (for U, VU, S, VU, HS) or mseccfg csr (for M).

Signed-off-by: Deepak Gupta <debug@rivosinc.com>
Co-developed-by: Jim Shu <jim.shu@sifive.com>
Co-developed-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20241008225010.1861630-5-debug@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>

show more ...

target/riscv: Introduce elp state and enabling controls for zicfilp

zicfilp introduces a new state elp ("expected landing pad") in cpu.
During normal execution, elp is idle (NO_LP_EXPECTED) i.e not

target/riscv: Introduce elp state and enabling controls for zicfilp

zicfilp introduces a new state elp ("expected landing pad") in cpu.
During normal execution, elp is idle (NO_LP_EXPECTED) i.e not expecting
landing pad. On an indirect call, elp moves LP_EXPECTED. When elp is
LP_EXPECTED, only a subsquent landing pad instruction can set state back
to NO_LP_EXPECTED. On reset, elp is set to NO_LP_EXPECTED.

zicfilp is enabled via bit2 in *envcfg CSRs. Enabling control for M-mode
is in mseccfg CSR at bit position 10.

On trap, elp state is saved away in *status.
Adds elp to the migration state as well.

Signed-off-by: Deepak Gupta <debug@rivosinc.com>
Co-developed-by: Jim Shu <jim.shu@sifive.com>
Co-developed-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20241008225010.1861630-4-debug@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>

show more ...

target/riscv: Add zicfilp extension

zicfilp [1] riscv cpu extension enables forward control flow integrity.
If enabled, all indirect calls must land on a landing pad instruction.

This patch sets up

target/riscv: Add zicfilp extension

zicfilp [1] riscv cpu extension enables forward control flow integrity.
If enabled, all indirect calls must land on a landing pad instruction.

This patch sets up space for zicfilp extension in cpuconfig. zicfilp
is dependend on zicsr.

[1] - https://github.com/riscv/riscv-cfi

Signed-off-by: Deepak Gupta <debug@rivosinc.com>
Co-developed-by: Jim Shu <jim.shu@sifive.com>
Co-developed-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20241008225010.1861630-3-debug@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>

show more ...

target/riscv: expose *envcfg csr and priv to qemu-user as well

Execution environment config CSR controlling user env and current
privilege state shouldn't be limited to qemu-system only. *envcfg
CSR

target/riscv: expose *envcfg csr and priv to qemu-user as well

Execution environment config CSR controlling user env and current
privilege state shouldn't be limited to qemu-system only. *envcfg
CSRs control enabling of features in next lesser mode. In some cases
bits *envcfg CSR can be lit up by kernel as part of kernel policy or
software (user app) can choose to opt-in by issuing a system call
(e.g. prctl). In case of qemu-user, it should be no different because
qemu is providing underlying execution environment facility and thus
either should provide some default value in *envcfg CSRs or react to
system calls (prctls) initiated from application. priv is set to PRV_U
and menvcfg/senvcfg set to 0 for qemu-user on reest.

`henvcfg` has been left for qemu-system only because it is not expected
that someone will use qemu-user where application is expected to have
hypervisor underneath which is controlling its execution environment. If
such a need arises then `henvcfg` could be exposed as well.

Relevant discussion:
https://lore.kernel.org/all/CAKmqyKOTVWPFep2msTQVdUmJErkH+bqCcKEQ4hAnyDFPdWKe0Q@mail.gmail.com/

Signed-off-by: Deepak Gupta <debug@rivosinc.com>
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20241008225010.1861630-2-debug@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>

show more ...

target/riscv: Set vtype.vill on CPU reset

The RISC-V unprivileged specification "31.3.11. State of Vector
Extension at Reset" has a note that recommends vtype.vill be set on
reset as part of ensurin

target/riscv: Set vtype.vill on CPU reset

The RISC-V unprivileged specification "31.3.11. State of Vector
Extension at Reset" has a note that recommends vtype.vill be set on
reset as part of ensuring that the vector extension have a consistent
state at reset.

This change now makes QEMU consistent with Spike which sets vtype.vill
on reset.

Signed-off-by: Rob Bradford <rbradford@rivosinc.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20240930165258.72258-1-rbradford@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>

show more ...

target/riscv: Add max32 CPU for RV64 QEMU

We may need 32-bit max for RV64 QEMU. Thus we add these two CPUs
for RV64 QEMU.

The reason we don't expose them to RV32 QEMU is that we already have
max cp

target/riscv: Add max32 CPU for RV64 QEMU

We may need 32-bit max for RV64 QEMU. Thus we add these two CPUs
for RV64 QEMU.

The reason we don't expose them to RV32 QEMU is that we already have
max cpu with the same configuration. Another reason is that we want
to follow the RISC-V custom where addw instruction doesn't exist in
RV32 CPU.

Signed-off-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Suggested-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20240919055048.562-8-zhiwei_liu@linux.alibaba.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>

show more ...

target/riscv: Enable RV32 CPU support in RV64 QEMU

Add gdb XML files and adjust CPU initialization to allow running RV32 CPUs
in RV64 QEMU.

Signed-off-by: TANG Tiancheng <tangtiancheng.ttc@alibaba-

target/riscv: Enable RV32 CPU support in RV64 QEMU

Add gdb XML files and adjust CPU initialization to allow running RV32 CPUs
in RV64 QEMU.

Signed-off-by: TANG Tiancheng <tangtiancheng.ttc@alibaba-inc.com>
Reviewed-by: Liu Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240919055048.562-7-zhiwei_liu@linux.alibaba.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>

show more ...

target/riscv: Correct mcause/scause bit width for RV32 in RV64 QEMU

Ensure mcause high bit is correctly set by using 32-bit width for RV32
mode and 64-bit width for RV64 mode.

Signed-off-by: TANG T

target/riscv: Correct mcause/scause bit width for RV32 in RV64 QEMU

Ensure mcause high bit is correctly set by using 32-bit width for RV32
mode and 64-bit width for RV64 mode.

Signed-off-by: TANG Tiancheng <tangtiancheng.ttc@alibaba-inc.com>
Reviewed-by: Liu Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240919055048.562-6-zhiwei_liu@linux.alibaba.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>

show more ...

target/riscv: Detect sxl to set bit width for RV32 in RV64

Ensure correct bit width based on sxl when running RV32 on RV64 QEMU.
This is required as MMU address translations run in S-mode.

Signed-o

target/riscv: Detect sxl to set bit width for RV32 in RV64

Ensure correct bit width based on sxl when running RV32 on RV64 QEMU.
This is required as MMU address translations run in S-mode.

Signed-off-by: TANG Tiancheng <tangtiancheng.ttc@alibaba-inc.com>
Reviewed-by: Liu Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240919055048.562-5-zhiwei_liu@linux.alibaba.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>

show more ...

target/riscv: Correct SXL return value for RV32 in RV64 QEMU

Ensure that riscv_cpu_sxl returns MXL_RV32 when runningRV32 in an
RV64 QEMU.

Signed-off-by: TANG Tiancheng <tangtiancheng.ttc@alibaba-in

target/riscv: Correct SXL return value for RV32 in RV64 QEMU

Ensure that riscv_cpu_sxl returns MXL_RV32 when runningRV32 in an
RV64 QEMU.

Signed-off-by: TANG Tiancheng <tangtiancheng.ttc@alibaba-inc.com>
Fixes: 05e6ca5e156 ("target/riscv: Ignore reserved bits in PTE for RV64")
Reviewed-by: Liu Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240919055048.562-4-zhiwei_liu@linux.alibaba.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>

show more ...

target/riscv: Adjust PMP size for no-MMU RV64 QEMU running RV32

Ensure pmp_size is correctly determined using mxl for RV32
in RV64 QEMU.

Signed-off-by: TANG Tiancheng <tangtiancheng.ttc@alibaba-inc

target/riscv: Adjust PMP size for no-MMU RV64 QEMU running RV32

Ensure pmp_size is correctly determined using mxl for RV32
in RV64 QEMU.

Signed-off-by: TANG Tiancheng <tangtiancheng.ttc@alibaba-inc.com>
Reviewed-by: Liu Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240919055048.562-3-zhiwei_liu@linux.alibaba.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>

show more ...

target/riscv/csr.c: Fix an access to VXSAT

The register VXSAT should be RW only to the first bit.
The remaining bits should be 0.

The RISC-V Instruction Set Manual Volume I: Unprivileged Architectu

target/riscv/csr.c: Fix an access to VXSAT

The register VXSAT should be RW only to the first bit.
The remaining bits should be 0.

The RISC-V Instruction Set Manual Volume I: Unprivileged Architecture

The vxsat CSR has a single read-write least-significant bit (vxsat[0])
that indicates if a fixed-point instruction has had to saturate an output
value to fit into a destination format. Bits vxsat[XLEN-1:1]
should be written as zeros.

Signed-off-by: Evgenii Prokopiev <evgenii.prokopiev@syntacore.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20241002084436.89347-1-evgenii.prokopiev@syntacore.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>

show more ...

Merge tag 'for-upstream' of https://gitlab.com/bonzini/qemu into staging

* pc: Add a description for the i8042 property
* kvm: support for nested FRED
* tests/unit: fix warning when compiling test-n

Merge tag 'for-upstream' of https://gitlab.com/bonzini/qemu into staging

* pc: Add a description for the i8042 property
* kvm: support for nested FRED
* tests/unit: fix warning when compiling test-nested-aio-poll with LTO
* kvm: refactoring of VM creation
* target/i386: expose IBPB-BRTYPE and SBPB CPUID bits to the guest
* hw/char: clean up serial
* remove virtfs-proxy-helper
* target/i386/kvm: Report which action failed in kvm_arch_put/get_registers
* qom: improvements to object_resolve_path*()

# -----BEGIN PGP SIGNATURE-----
#
# iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmb++MsUHHBib256aW5p
# QHJlZGhhdC5jb20ACgkQv/vSX3jHroPVnwf/cdvfxvDm22tEdlh8vHlV17HtVdcC
# Hw334M/3PDvbTmGzPBg26lzo4nFS6SLrZ8ETCeqvuJrtKzqVk9bI8ssZW5KA4ijM
# nkxguRPHO8E6U33ZSucc+Hn56+bAx4I2X80dLKXJ87OsbMffIeJ6aHGSEI1+fKVh
# pK7q53+Y3lQWuRBGhDIyKNuzqU4g+irpQwXOhux63bV3ADadmsqzExP6Gmtl8OKM
# DylPu1oK7EPZumlSiJa7Gy1xBqL4Rc4wGPNYx2RVRjp+i7W2/Y1uehm3wSBw+SXC
# a6b7SvLoYfWYS14/qCF4cBL3sJH/0f/4g8ZAhDDxi2i5kBr0/5oioDyE/A==
# =/zo4
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 03 Oct 2024 21:04:27 BST
# gpg: using RSA key F13338574B662389866C7682BFFBD25F78C7AE83
# gpg: issuer "pbonzini@redhat.com"
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [full]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [full]
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83

* tag 'for-upstream' of https://gitlab.com/bonzini/qemu: (23 commits)
qom: update object_resolve_path*() documentation
qom: set *ambiguous on all paths
qom: rename object_resolve_path_type() "ambiguousp"
target/i386/kvm: Report which action failed in kvm_arch_put/get_registers
kvm: Allow kvm_arch_get/put_registers to accept Error**
accel/kvm: refactor dirty ring setup
minikconf: print error entirely on stderr
9p: remove 'proxy' filesystem backend driver
hw/char: Extract serial-mm
hw/char/serial.h: Extract serial-isa.h
hw: Remove unused inclusion of hw/char/serial.h
target/i386: Expose IBPB-BRTYPE and SBPB CPUID bits to the guest
kvm: refactor core virtual machine creation into its own function
kvm/i386: replace identity_base variable with a constant
kvm/i386: refactor kvm_arch_init and split it into smaller functions
kvm: replace fprintf with error_report()/printf() in kvm_init()
kvm/i386: fix return values of is_host_cpu_intel()
kvm/i386: make kvm_filter_msr() and related definitions private to kvm module
hw/i386/pc: Add a description for the i8042 property
tests/unit: remove block layer code from test-nested-aio-poll
...

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

# Conflicts:
# hw/arm/Kconfig
# hw/arm/pxa2xx.c

show more ...

kvm: Allow kvm_arch_get/put_registers to accept Error**

This is necessary to provide discernible error messages to the caller.

Signed-off-by: Julia Suvorova <jusual@redhat.com>
Reviewed-by: Peter X

kvm: Allow kvm_arch_get/put_registers to accept Error**

This is necessary to provide discernible error messages to the caller.

Signed-off-by: Julia Suvorova <jusual@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Link: https://lore.kernel.org/r/20240927104743.218468-2-jusual@redhat.com
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

show more ...

target/riscv/cpu_helper: Fix linking problem with semihosting disabled

If QEMU has been configured with "--without-default-devices", the build
is currently failing with:

/usr/bin/ld: libqemu-riscv

target/riscv/cpu_helper: Fix linking problem with semihosting disabled

If QEMU has been configured with "--without-default-devices", the build
is currently failing with:

/usr/bin/ld: libqemu-riscv32-softmmu.a.p/target_riscv_cpu_helper.c.o:
in function `riscv_cpu_do_interrupt':
.../qemu/target/riscv/cpu_helper.c:1678:(.text+0x2214): undefined
reference to `do_common_semihosting'

We always want semihosting to be enabled if TCG is available, so change
the "imply" statements in the Kconfig file to "select", and make sure to
avoid calling into do_common_semihosting() if TCG is not available.

Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240906094858.718105-1-thuth@redhat.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>

show more ...

target/riscv32: Fix masking of physical address

C doesn't extend the sign bit for unsigned types since there isn't a
sign bit to extend. This means a promotion of a u32 to a u64 results
in the upper

target/riscv32: Fix masking of physical address

C doesn't extend the sign bit for unsigned types since there isn't a
sign bit to extend. This means a promotion of a u32 to a u64 results
in the upper 32 bits of the u64 being zero. If that result is then
used as a mask on another u64 the upper 32 bits will be cleared. rv32
physical addresses may be up to 34 bits wide, so we don't want to
clear the high bits while page aligning the address. The fix is to
use hwaddr for the mask, which, even on rv32, is 64-bits wide.

Fixes: af3fc195e3c8 ("target/riscv: Change the TLB page size depends on PMP entries.")
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20240909083241.43836-2-ajones@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>

show more ...

target: riscv: Add Svvptc extension support

The Svvptc extension describes a uarch that does not cache invalid TLB
entries: that's the case for qemu so there is nothing particular to
implement other

target: riscv: Add Svvptc extension support

The Svvptc extension describes a uarch that does not cache invalid TLB
entries: that's the case for qemu so there is nothing particular to
implement other than the introduction of this extension.

Since qemu already exposes Svvptc behaviour, let's enable it by default
since it allows to drastically reduce the number of sfence.vma emitted
by S-mode.

Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240828083651.203861-1-alexghiti@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>

show more ...