ARM64: dts: meson: accept MAC addr from u-boot environment

Extend configuring the MAC address from u-boot to all meson boards.

I didn't test this changeset but having checked libret

ARM64: dts: meson: accept MAC addr from u-boot environment

Extend configuring the MAC address from u-boot to all meson boards.

I didn't test this changeset but having checked libretech's u-boot
tree I believe it should just work.

Signed-off-by: Jorge Ramirez-Ortiz <jramirez@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

ARM64: dts: meson-gx: Add HDMI_5V regulator on selected boards

On reference boards and derivatives, the HDMI Logic is powered by an external
5V regulator.
This regulator was set by t

ARM64: dts: meson-gx: Add HDMI_5V regulator on selected boards

On reference boards and derivatives, the HDMI Logic is powered by an external
5V regulator.
This regulator was set by the Vendor U-Boot, add the regulator and set it always-on for now.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

ARM64: dts: meson-gxl: Take eMMC data strobe out of eMMC pins

Since the Data Strobe pin is optional, take it out of the default
eMMC pins and add a separate entry.

Signed-off-by

ARM64: dts: meson-gxl: Take eMMC data strobe out of eMMC pins

Since the Data Strobe pin is optional, take it out of the default
eMMC pins and add a separate entry.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

ARM64: dts: meson: add mmc clk gate pins

Add the pinctrl to switch mmc clk pins in gpio (pulled down) mode. This
is necessary to be able to gate the clk outside of the SoC while
keep

ARM64: dts: meson: add mmc clk gate pins

Add the pinctrl to switch mmc clk pins in gpio (pulled down) mode. This
is necessary to be able to gate the clk outside of the SoC while
keeping it running in the controller

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

ARM64: dts: meson: remove cap-sd-highspeed from emmc nodes

It does not make much sense to define cap-sd-highspeed in the emmc nodes
Just remove it.

Signed-off-by: Jerome Brunet

ARM64: dts: meson: remove cap-sd-highspeed from emmc nodes

It does not make much sense to define cap-sd-highspeed in the emmc nodes
Just remove it.

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

ARM64: dts: meson-gxl: improve support for the P212 reference design

The Amlogic P212 reference design is used by other devices as well, such
as (for example) the Khadas VIM boards. Thus

ARM64: dts: meson-gxl: improve support for the P212 reference design

The Amlogic P212 reference design is used by other devices as well, such
as (for example) the Khadas VIM boards. Thus this patch adds and moves
all common entries from meson-gxl-s905x-p212.dts to a new, separate
meson-gxl-s905x-p212.dtsi (which can be re-used on boards such as the
Khadas VIM).
Support for all boards based on the P212 reference design includes:
- enabling IR support
- enabling the SAR ADC (SARADC_CH1 is connected to a resistor which
indicates the hardware revision, a similar design is found on the
Khadas VIM boards)
- all MMC controllers (which means that SDIO wifi, the SD card and the
eMMC are now supported)
- pwm_ef as dependency for the SDIO wifi modules
- uart_A which is connected to the bluetooth module (the bluetooth
module itself is not enabled yet due to missing devicetree bindings
for the Broadcom serial bluetooth devices)
- uart_AO is moved to the .dtsi (as all known devices use it as their
boot-console)

Specific to the P212 board:
- this also enables the CVBS connector (which is not available on the
Khadas VIM boards for example)
- Realtek based SDIO wifi (instead of Broadcom which most other devices
use)

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...