ARM64: dts: meson: accept MAC addr from u-boot environment

Extend configuring the MAC address from u-boot to all meson boards.

I didn't test this changeset but having checked libret

ARM64: dts: meson: accept MAC addr from u-boot environment

Extend configuring the MAC address from u-boot to all meson boards.

I didn't test this changeset but having checked libretech's u-boot
tree I believe it should just work.

Signed-off-by: Jorge Ramirez-Ortiz <jramirez@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

ARM64: dts: meson-gxl: Take eMMC data strobe out of eMMC pins

Since the Data Strobe pin is optional, take it out of the default
eMMC pins and add a separate entry.

Signed-off-by

ARM64: dts: meson-gxl: Take eMMC data strobe out of eMMC pins

Since the Data Strobe pin is optional, take it out of the default
eMMC pins and add a separate entry.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

ARM64: dts: meson: add mmc clk gate pins

Add the pinctrl to switch mmc clk pins in gpio (pulled down) mode. This
is necessary to be able to gate the clk outside of the SoC while
keep

ARM64: dts: meson: add mmc clk gate pins

Add the pinctrl to switch mmc clk pins in gpio (pulled down) mode. This
is necessary to be able to gate the clk outside of the SoC while
keeping it running in the controller

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

ARM64: dts: meson: remove cap-sd-highspeed from emmc nodes

It does not make much sense to define cap-sd-highspeed in the emmc nodes
Just remove it.

Signed-off-by: Jerome Brunet

ARM64: dts: meson: remove cap-sd-highspeed from emmc nodes

It does not make much sense to define cap-sd-highspeed in the emmc nodes
Just remove it.

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

arm64: dts: meson-gxbb-vega-s95: Fix node order

Sort nodes referenced by label alphabetically.

Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Hilman <khil

arm64: dts: meson-gxbb-vega-s95: Fix node order

Sort nodes referenced by label alphabetically.

Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

arm64: dts: meson-gxbb-vega-s95: Fix Wifi node name

bcrmf -> brcmf -> wifi

Fixes: ab5b24fdd2d5 ("ARM64: dts: meson-gxbb-vega-s95: Add SD/SDIO/MMC and PWM nodes")
Cc: Martin Blum

arm64: dts: meson-gxbb-vega-s95: Fix Wifi node name

bcrmf -> brcmf -> wifi

Fixes: ab5b24fdd2d5 ("ARM64: dts: meson-gxbb-vega-s95: Add SD/SDIO/MMC and PWM nodes")
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

ARM64: dts: amlogic: add the ethernet TX delay configuration

This adds the amlogic,tx-delay-ns property with the old (hardcoded)
default value of 2ns to all boards which are using an RGM

ARM64: dts: amlogic: add the ethernet TX delay configuration

This adds the amlogic,tx-delay-ns property with the old (hardcoded)
default value of 2ns to all boards which are using an RGMII ethernet
PHY.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

ARM64: dts: meson-gxbb-vega-s95: add the ethernet PHY's reset GPIO

This resets the ethernet PHY during boot to get the PHY into a "clean"
state.
While here also specify the phy-handl

ARM64: dts: meson-gxbb-vega-s95: add the ethernet PHY's reset GPIO

This resets the ethernet PHY during boot to get the PHY into a "clean"
state.
While here also specify the phy-handle of the ethmac node to make the
PHY configuration similar to the one we have on GXL devices. This will
allow us to specify OF-properties for the PHY itself.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

ARM64: dts: meson-gxbb-vega-s95: Add LED

There is one blue LED on the front of the device. Keep it lit and
configure it as panic indicator.

Signed-off-by: Andreas Färber <afaerb

ARM64: dts: meson-gxbb-vega-s95: Add LED

There is one blue LED on the front of the device. Keep it lit and
configure it as panic indicator.

Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

ARM64: dts: meson-gxbb-vega-s95: Add SD/SDIO/MMC and PWM nodes

All boards from the Tronsmart Vega S95 series are sharing similar MMC
based hardware.
sd_emmc_a is used to connect a Br

ARM64: dts: meson-gxbb-vega-s95: Add SD/SDIO/MMC and PWM nodes

All boards from the Tronsmart Vega S95 series are sharing similar MMC
based hardware.
sd_emmc_a is used to connect a Broadcom based SDIO wifi card (supported
by the brcmfmac driver). The 32.768KHz LPO clock for the wifi chip is
generated by PWM_E.
sd_emmc_b is routed to the SD-card. Unlike p20x there is no GPIO
regulator, meaning it only supports 3.3V (which seems to be hard-wired).
The eMMC chip is connected to sd_emmc_c and is implemented similar to
the meson-gxbb-p20x boards (meaning that hard-wired fixed regulators
are used).

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

ARM64: dts: meson-gxbb: Add rmii pinctrl node and rename rgmii node

For boards only supporting 10/100 ethernet over a RMII PHY link, add
a separate pinctrl node. By the way, rename the e

ARM64: dts: meson-gxbb: Add rmii pinctrl node and rename rgmii node

For boards only supporting 10/100 ethernet over a RMII PHY link, add
a separate pinctrl node. By the way, rename the existing node to rgmii
specific naming in all boards dts.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

ARM64: dts: meson-gxbb-vega-s95: Enable USB Nodes

Enable both gxbb USB controller and add a 5V regulator for the OTG port
VBUS

Signed-off-by: Martin Blumenstingl <martin.blumens

ARM64: dts: meson-gxbb-vega-s95: Enable USB Nodes

Enable both gxbb USB controller and add a 5V regulator for the OTG port
VBUS

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

ARM64: dts: amlogic: enable ethernet on all Tronsmart Vega S95 devices

All of these have a Realtek Gbit RGMII PHY.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail

ARM64: dts: amlogic: enable ethernet on all Tronsmart Vega S95 devices

All of these have a Realtek Gbit RGMII PHY.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

ARM64: dts: meson-gxbb: Enable the the IR decoder on supported boards

Enable the Infrared Remote Controller on boards which have an Infrared
receiver.

Signed-off-by: Martin Blum

ARM64: dts: meson-gxbb: Enable the the IR decoder on supported boards

Enable the Infrared Remote Controller on boards which have an Infrared
receiver.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

ARM64: dts: amlogic: Enable pin controller on GXBB-based platforms

Update DTS and DTSI files to enable the pin controller. We also now
support the blinking blue LED on the Odroid-C2.

ARM64: dts: amlogic: Enable pin controller on GXBB-based platforms

Update DTS and DTSI files to enable the pin controller. We also now
support the blinking blue LED on the Odroid-C2.

Signed-off-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

ARM64: dts: amlogic: update serial aliases

Apparently, it's not valid to have an alias point to a disabled device.
Fix this by moving the aliases that are used (serial0) into the files

ARM64: dts: amlogic: update serial aliases

Apparently, it's not valid to have an alias point to a disabled device.
Fix this by moving the aliases that are used (serial0) into the files
that use them, and remove aliases to disabled devices (serial1).

Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>

show more ...

ARM64: dts: amlogic: Add Tronsmart Vega S95 configs

Add Device Trees for Tronsmart Vega S95 Pro, Meta and Telos TV boxes.

Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed

ARM64: dts: amlogic: Add Tronsmart Vega S95 configs

Add Device Trees for Tronsmart Vega S95 Pro, Meta and Telos TV boxes.

Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Carlo Caione <carlo@endlessm.com>

show more ...