ARM64: dts: meson-gxbb-vega-s95: add the ethernet PHY's reset GPIO

This resets the ethernet PHY during boot to get the PHY into a "clean"
state.
While here also specify the phy-handle of the ethmac

ARM64: dts: meson-gxbb-vega-s95: add the ethernet PHY's reset GPIO

This resets the ethernet PHY during boot to get the PHY into a "clean"
state.
While here also specify the phy-handle of the ethmac node to make the
PHY configuration similar to the one we have on GXL devices. This will
allow us to specify OF-properties for the PHY itself.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

ARM64: dts: meson-gxbb-vega-s95: Add LED

There is one blue LED on the front of the device. Keep it lit and
configure it as panic indicator.

Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-o

ARM64: dts: meson-gxbb-vega-s95: Add LED

There is one blue LED on the front of the device. Keep it lit and
configure it as panic indicator.

Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

ARM64: dts: meson-gxbb-vega-s95: Add SD/SDIO/MMC and PWM nodes

All boards from the Tronsmart Vega S95 series are sharing similar MMC
based hardware.
sd_emmc_a is used to connect a Broadcom based SDI

ARM64: dts: meson-gxbb-vega-s95: Add SD/SDIO/MMC and PWM nodes

All boards from the Tronsmart Vega S95 series are sharing similar MMC
based hardware.
sd_emmc_a is used to connect a Broadcom based SDIO wifi card (supported
by the brcmfmac driver). The 32.768KHz LPO clock for the wifi chip is
generated by PWM_E.
sd_emmc_b is routed to the SD-card. Unlike p20x there is no GPIO
regulator, meaning it only supports 3.3V (which seems to be hard-wired).
The eMMC chip is connected to sd_emmc_c and is implemented similar to
the meson-gxbb-p20x boards (meaning that hard-wired fixed regulators
are used).

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

ARM64: dts: meson-gxbb: Add rmii pinctrl node and rename rgmii node

For boards only supporting 10/100 ethernet over a RMII PHY link, add
a separate pinctrl node. By the way, rename the existing node

ARM64: dts: meson-gxbb: Add rmii pinctrl node and rename rgmii node

For boards only supporting 10/100 ethernet over a RMII PHY link, add
a separate pinctrl node. By the way, rename the existing node to rgmii
specific naming in all boards dts.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

ARM64: dts: meson-gxbb-vega-s95: Enable USB Nodes

Enable both gxbb USB controller and add a 5V regulator for the OTG port
VBUS

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com

ARM64: dts: meson-gxbb-vega-s95: Enable USB Nodes

Enable both gxbb USB controller and add a 5V regulator for the OTG port
VBUS

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

ARM64: dts: amlogic: enable ethernet on all Tronsmart Vega S95 devices

All of these have a Realtek Gbit RGMII PHY.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by:

ARM64: dts: amlogic: enable ethernet on all Tronsmart Vega S95 devices

All of these have a Realtek Gbit RGMII PHY.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

ARM64: dts: meson-gxbb: Enable the the IR decoder on supported boards

Enable the Infrared Remote Controller on boards which have an Infrared
receiver.

Signed-off-by: Martin Blumenstingl <martin.blu

ARM64: dts: meson-gxbb: Enable the the IR decoder on supported boards

Enable the Infrared Remote Controller on boards which have an Infrared
receiver.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

ARM64: dts: amlogic: Enable pin controller on GXBB-based platforms

Update DTS and DTSI files to enable the pin controller. We also now
support the blinking blue LED on the Odroid-C2.

Signed-off-by:

ARM64: dts: amlogic: Enable pin controller on GXBB-based platforms

Update DTS and DTSI files to enable the pin controller. We also now
support the blinking blue LED on the Odroid-C2.

Signed-off-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

ARM64: dts: amlogic: update serial aliases

Apparently, it's not valid to have an alias point to a disabled device.
Fix this by moving the aliases that are used (serial0) into the files
that use them

ARM64: dts: amlogic: update serial aliases

Apparently, it's not valid to have an alias point to a disabled device.
Fix this by moving the aliases that are used (serial0) into the files
that use them, and remove aliases to disabled devices (serial1).

Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>

show more ...

ARM64: dts: amlogic: Add Tronsmart Vega S95 configs

Add Device Trees for Tronsmart Vega S95 Pro, Meta and Telos TV boxes.

Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Carlo Caion

ARM64: dts: amlogic: Add Tronsmart Vega S95 configs

Add Device Trees for Tronsmart Vega S95 Pro, Meta and Telos TV boxes.

Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Carlo Caione <carlo@endlessm.com>

show more ...

arm64: dts: meson: fix PHY deassert timing requirements

[ Upstream commit c183c406c4321002fe85b345b51bc1a3a04b6d33 ]

According to the datasheet (Rev. 1.9) the RTL8211F requires at l

arm64: dts: meson: fix PHY deassert timing requirements

[ Upstream commit c183c406c4321002fe85b345b51bc1a3a04b6d33 ]

According to the datasheet (Rev. 1.9) the RTL8211F requires at least
72ms "for internal circuits settling time" before accessing the PHY
registers. This fixes an issue seen on ODROID-C2 where the Ethernet
link doesn't come up when using ip link set down/up:
[ 6630.714855] meson8b-dwmac c9410000.ethernet eth0: Link is Down
[ 6630.785775] meson8b-dwmac c9410000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211F Gigabit Ethernet] (irq=36)
[ 6630.893071] meson8b-dwmac c9410000.ethernet: Failed to reset the dma
[ 6630.893800] meson8b-dwmac c9410000.ethernet eth0: stmmac_hw_setup: DMA engine initialization failed
[ 6630.902835] meson8b-dwmac c9410000.ethernet eth0: stmmac_open: Hw setup failed

Fixes: f29cabf240ed ("arm64: dts: meson: use the generic Ethernet PHY reset GPIO bindings")
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/4a322c198b86e4c8b3dda015560a683babea4d63.1607363522.git.stefan@agner.ch
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

arm64: dts: meson: fix leds subnodes name

Fix the leds subnode names to match (^led-[0-9a-f]$|led)

It fixes:
meson-g12b-a311d-khadas-vim3.dt.yaml: leds: 'red', 'white' do not ma

arm64: dts: meson: fix leds subnodes name

Fix the leds subnode names to match (^led-[0-9a-f]$|led)

It fixes:
meson-g12b-a311d-khadas-vim3.dt.yaml: leds: 'red', 'white' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-g12b-s922x-khadas-vim3.dt.yaml: leds: 'red', 'white' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-g12b-odroid-n2.dt.yaml: leds: 'blue' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxbb-nanopi-k2.dt.yaml: leds: 'stat' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxbb-nexbox-a95x.dt.yaml: leds: 'blue' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxbb-odroidc2.dt.yaml: leds: 'blue' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxbb-vega-s95-pro.dt.yaml: leds: 'blue' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxbb-vega-s95-meta.dt.yaml: leds: 'blue' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxbb-vega-s95-telos.dt.yaml: leds: 'blue' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxbb-wetek-hub.dt.yaml: leds: 'system' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxbb-wetek-play2.dt.yaml: leds: 'ethernet', 'system', 'wifi' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxl-s905x-libretech-cc.dt.yaml: leds: 'blue', 'system' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxl-s905d-libretech-pc.dt.yaml: leds: 'blue', 'green' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxm-rbox-pro.dt.yaml: leds: 'blue', 'red' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxm-s912-libretech-pc.dt.yaml: leds: 'blue', 'green' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-sm1-sei610.dt.yaml: leds: 'bluetooth' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-sm1-khadas-vim3l.dt.yaml: leds: 'red', 'white' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200326165958.19274-6-narmstrong@baylibre.com

show more ...

arm64: dts: meson-gxbb-vega-s95: fix bluetooth node

This was missed from the previous fix.

Fixes: b07a11dbdfeb ("arm64: dts: meson-gxbb-vega-s95: fix WiFi/BT module support")

arm64: dts: meson-gxbb-vega-s95: fix bluetooth node

This was missed from the previous fix.

Fixes: b07a11dbdfeb ("arm64: dts: meson-gxbb-vega-s95: fix WiFi/BT module support")

Suggested-by: Oleg Ivanov <balbes-150@yandex.ru>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/1582220642-14133-1-git-send-email-christianshewitt@gmail.com

show more ...

arm64: dts: meson-gxbb-vega-s95: set rc-vega-s9x ir keymap

Add the rc-vega-s9x keymap to the existing IR node in the device tree.

Signed-off-by: Christian Hewitt <christianshewitt@g

arm64: dts: meson-gxbb-vega-s95: set rc-vega-s9x ir keymap

Add the rc-vega-s9x keymap to the existing IR node in the device tree.

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

arm64: dts: meson-gxbb-vega-s95: add keep-power-in-suspend property in SDIO node

The WiFi firmware requires that the power is kept enabled while in
suspend mode. Add the keep-power-in-su

arm64: dts: meson-gxbb-vega-s95: add keep-power-in-suspend property in SDIO node

The WiFi firmware requires that the power is kept enabled while in
suspend mode. Add the keep-power-in-suspend property in the SDIO node
to specify that the power must be kept when entering in a system wide
suspend state.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

arm64: dts: meson: use the generic Ethernet PHY reset GPIO bindings

The snps,reset-gpio bindings are deprecated in favour of the generic
"Ethernet PHY reset" bindings.

Replace s

arm64: dts: meson: use the generic Ethernet PHY reset GPIO bindings

The snps,reset-gpio bindings are deprecated in favour of the generic
"Ethernet PHY reset" bindings.

Replace snps,reset-gpio from the &ethmac node with reset-gpios in the
ethernet-phy node. The old snps,reset-active-low property is now encoded
directly as GPIO flag inside the reset-gpios property.

snps,reset-delays-us is converted to reset-assert-us and
reset-deassert-us. reset-assert-us is the second cell from
snps,reset-delays-us while reset-deassert-us was the third cell.

Instead of blindly copying the old values (which seems strange since
they gave the PHY one second to come out of reset) over this also
updates the delays based on the datasheets:
- the Realtek RTL8211F PHY needs a 10ms assert delay (the datasheet
mentions: "For a complete PHY reset, this pin must be asserted low
for at least 10ms") and a 30ms deassert delay (the datasheet
mentions: "Wait for a further 30ms (for internal circuits settling
time) before accessing the PHY register". This applies to the
following boards: GXBB NanoPi K2, GXBB Odroid-C2, GXBB Vega S95
variants, GXBB Wetek variants, GXL P230, GXM Khadas VIM2, GXM Nexbox
A1, GXM Q200, GXM RBox Pro boards.
- the ICPlus IP101GR PHY needs a 10ms assert delay (the datasheet
mentions: "Trst | Reset period | 10ms") and a deassert delay of 10ms
as well (the datasheet mentions: "Tclk_MII_rdy | MII/RMII clock
output ready after reset released | 10ms"). This applies to the GXBB
Nexbox A95X board.
- the Micrel KSZ9031 seems to require a 100us delay but use the same
(seemingly safe) values from RTL8211F due to lack of a board to verify
this. This applies to the GXBB P200 board.

The GXBB P201 board is left out from this conversion because it doesn't
have a dedicated PHY node (because it's not clear which PHY is used on
that board).

Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

arm64: dts: meson-gxbb-vega-s95: add ethernet PHY interrupt

Add the external ethernet PHY interrupt on the Vega S95 board.

Suggested-by: Christian Hewitt <christianshewitt@gmail.com

arm64: dts: meson-gxbb-vega-s95: add ethernet PHY interrupt

Add the external ethernet PHY interrupt on the Vega S95 board.

Suggested-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

arm64: dts: meson-gxbb-vega-s95: fix WiFi/BT module support

Fix the SDIO WiFi support and add proper Bluetooth support on the
Vega S95 board.

Suggested-by: Christian Hewitt <chr

arm64: dts: meson-gxbb-vega-s95: fix WiFi/BT module support

Fix the SDIO WiFi support and add proper Bluetooth support on the
Vega S95 board.

Suggested-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

arm64: dts: meson-gxbb-vega-s95: enable SARADC

Add SARARC node and associated regulator to support reading the
ADC inputs on the Vega S95

Suggested-by: Christian Hewitt <christi

arm64: dts: meson-gxbb-vega-s95: enable SARADC

Add SARARC node and associated regulator to support reading the
ADC inputs on the Vega S95

Suggested-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

arm64: dts: meson-gxbb-vega-s95: enable CEC

Add CEC nodes to support CEC communication on Vega S95

Suggested-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Nei

arm64: dts: meson-gxbb-vega-s95: enable CEC

Add CEC nodes to support CEC communication on Vega S95

Suggested-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

arm64: dts: meson-gxbb-vega-s95: add HDMI nodes

Add HDMI nodes to support graphics on Vega S95

Suggested-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Ar

arm64: dts: meson-gxbb-vega-s95: add HDMI nodes

Add HDMI nodes to support graphics on Vega S95

Suggested-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

arm64: dts: meson-gxbb-vega-s95: fix regulators

Align the regulator names with other GXBB SoCS for upcoming
SARADC support and SDIO/SDCard fixes.
Also fix how regulators are passed t

arm64: dts: meson-gxbb-vega-s95: fix regulators

Align the regulator names with other GXBB SoCS for upcoming
SARADC support and SDIO/SDCard fixes.
Also fix how regulators are passed to MMC controllers & USB.

Suggested-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

arm64: dts: meson: fix mmc v2 chips max frequencies

According the datasheets, emmc v2 chips (gxbb and gxl) don't support
more that 100Mhz in UHS-1 SD modes and HS in SDIO.

Align

arm64: dts: meson: fix mmc v2 chips max frequencies

According the datasheets, emmc v2 chips (gxbb and gxl) don't support
more that 100Mhz in UHS-1 SD modes and HS in SDIO.

Align the max-frequency to 100MHz for UHS-1 and 50MHz for HS

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

arm64: dts: meson: Fix mmc cd-gpios polarity

Commit 89a5e15bcba8 ("gpio/mmc/of: Respect polarity in the device tree")
changed the behavior of "cd-inverted" to follow the device tree bind

arm64: dts: meson: Fix mmc cd-gpios polarity

Commit 89a5e15bcba8 ("gpio/mmc/of: Respect polarity in the device tree")
changed the behavior of "cd-inverted" to follow the device tree bindings
specification:
According to SDHCI standard, CD lines are specified as "active low".
Using the "cd-inverted" property means that the CD line is "active high".

Fix the SD card description for meson by setting the cd-gpios as
"active low", according to the boards specifications, and dropping the
"cd-inverted" property.

Fixes: 89a5e15bcba8 ("gpio/mmc/of: Respect polarity in the device tree")
Signed-off-by: Loys Ollivier <lollivier@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

ARM64: dts: amlogic: Convert to new-style SPDX license identifiers

Move the SPDX-License-Identifier lines to the top and drop the
license splat.

Signed-off-by: Neil Armstrong <n

ARM64: dts: amlogic: Convert to new-style SPDX license identifiers

Move the SPDX-License-Identifier lines to the top and drop the
license splat.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...