[PATCH] USB: delete the nokia_dku2 driver

It was causing too many problems, and this is not the proper type of
driver for this device.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-

[PATCH] USB: delete the nokia_dku2 driver

It was causing too many problems, and this is not the proper type of
driver for this device.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

show more ...

[PATCH] USB: add nokia_dku2 driver

This driver comes from the gnokii project.
Was further cleaned up by me to match recent usb-serial core changes.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

[PATCH] USB: add Option Card driver

This patch adds a new driver for "Option" cards. This is a GSM data card,
controlled by three "serial ports" which are connected via an OHCI adapter,
all located

[PATCH] USB: add Option Card driver

This patch adds a new driver for "Option" cards. This is a GSM data card,
controlled by three "serial ports" which are connected via an OHCI adapter,
all located on an oversized PC-Card. It's sold by several GSM service
providers.

Traditionally, this card has been accessed via the standard serial driver
and appropriate vendor= and product= options. However, testing has
revealed several problems with this approach, including hung data transfers
and lost data blocks when receiving.

Therefore, I've written a separate driver.

Signed-off-by: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

show more ...

[PATCH] USB: add a driver for the AirPrime CDMA Wireless PC card.

Easier than trying to use the generic usb-serial driver.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

[PATCH] USB: add HP49G+ Calculator USB Serial support

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Linux-2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in

Linux-2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

show more ...

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

Many source files in the tree are missing licensing information, which
makes it harder for compliance tools

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.

For non */uapi/* files that summary was:

SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139

and resulted in the first patch in this series.

If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:

SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930

and resulted in the second patch in this series.

- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:

SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1

and that resulted in the third patch in this series.

- when the two scanners agreed on the detected license(s), that became
the concluded license(s).

- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.

- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).

- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.

- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct

This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

USB: serial: add uPD78F0730 USB to Serial Adaptor Driver

The adaptor can be found on development boards for 78k, RL78 and V850
microcontrollers produced by Renesas Electronics Corporatio

USB: serial: add uPD78F0730 USB to Serial Adaptor Driver

The adaptor can be found on development boards for 78k, RL78 and V850
microcontrollers produced by Renesas Electronics Corporation.

This is not a full-featured USB to serial converter, however it allows
basic communication and simple control which is enough for programming of
on-board flash and debugging through a debug monitor.

uPD78F0730 is a USB-enabled microcontroller with USB-to-UART conversion
implemented in firmware.

This chip is also present in some debugging adaptors which use it for
USB-to-SPI conversion as well. The present driver doesn't cover SPI,
only USB-to-UART conversion is supported.

Signed-off-by: Maksim Salau <maksim.salau@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>

show more ...

USB: serial: add Fintek F81532/534 driver

This driver is for Fintek F81532/F81534 USB to Serial Ports IC.

F81532 spec:
https://drive.google.com/file/d/0B8vRwwYO7aMFOTRRMmhWQVNva

USB: serial: add Fintek F81532/534 driver

This driver is for Fintek F81532/F81534 USB to Serial Ports IC.

F81532 spec:
https://drive.google.com/file/d/0B8vRwwYO7aMFOTRRMmhWQVNvajQ/view?usp=
sharing

F81534 spec:
https://drive.google.com/file/d/0B8vRwwYO7aMFV29pQWJqbVBNc00/view?usp=
sharing

Features:
1. F81532 is 1-to-2 & F81534 is 1-to-4 serial ports IC
2. Support Baudrate from B50 to B115200.

Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>

show more ...

Revert "USB: serial: add Moxa UPORT 11x0 driver"

This reverts commit 0b2b093ad405b56a9e6f4f20a25da77ebfa9549c.

Turns out the MOXA vendor driver was basically just a copy of the

Revert "USB: serial: add Moxa UPORT 11x0 driver"

This reverts commit 0b2b093ad405b56a9e6f4f20a25da77ebfa9549c.

Turns out the MOXA vendor driver was basically just a copy of the
ti_usb_3410_5052 driver. We don't want two drivers for the same chip
even if mxu11x0 had gotten some much needed clean up before merge. So
let's remove the mxu11x0 driver, add support for these Moxa devices to
the TI driver, and then clean that driver up instead.

Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

USB: serial: add Moxa UPORT 11x0 driver

Add a driver which supports :

- UPort 1110 : 1 port RS-232 USB to Serial Hub.
- UPort 1130 : 1 port RS-422/485 USB to Serial Hub.
-

USB: serial: add Moxa UPORT 11x0 driver

Add a driver which supports :

- UPort 1110 : 1 port RS-232 USB to Serial Hub.
- UPort 1130 : 1 port RS-422/485 USB to Serial Hub.
- UPort 1130I : 1 port RS-422/485 USB to Serial Hub with Isolation.
- UPort 1150 : 1 port RS-232/422/485 USB to Serial Hub.
- UPort 1150I : 1 port RS-232/422/485 USB to Serial Hub with Isolation.

This driver is based on GPL MOXA driver written by Hen Huang and available
on MOXA website. The original driver was based on io_ti serial driver.

Signed-off-by: Mathieu OTHACEHE <m.othacehe@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>

show more ...

USB: serial: remove zte_ev driver

The zte_ev driver is based on code (once) distributed by ZTE that still
appears to originally have been reverse-engineered and bolted onto the
gener

USB: serial: remove zte_ev driver

The zte_ev driver is based on code (once) distributed by ZTE that still
appears to originally have been reverse-engineered and bolted onto the
generic driver.

A closer analysis of the zte_ev setup code reveals that it consists of
standard CDC requests (SET/GET_LINE_CODING and SET_CONTROL_LINE_STATE)
but unfortunately fails to get some of those right. In particular, as
reported by Lei Liu, it fails to lower DTR/RTS on close. It also appears
that the control requests lack the interface argument.

Since line control is already handled properly by the option driver, and
the SET/GET_LINE_CODING requests appears to be redundant (amounts to a
SET 9600 8N1) let's remove the redundant zte_ev driver.

Also move the remaining ZTE PIDs to the generic option modem driver.

Reported-by: Lei Liu <liu.lei78@zte.com.cn>
Signed-off-by: Johan Hovold <johan@kernel.org>

show more ...

USB: serial: add Moxa UPORT 12XX/14XX/16XX driver

Add a driver which supports the following Moxa USB to serial converters:
* 2 ports : UPort 1250, UPort 1250I
* 4 ports :

USB: serial: add Moxa UPORT 12XX/14XX/16XX driver

Add a driver which supports the following Moxa USB to serial converters:
* 2 ports : UPort 1250, UPort 1250I
* 4 ports : UPort 1410, UPort 1450, UPort 1450I
* 8 ports : UPort 1610-8, UPort 1650-8
* 16 ports : UPort 1610-16, UPort 1650-16

The UPORT devices don't directly fit the USB serial model. USB serial
assumes a bulk in/out endpoint pair per serial port. Thus a dual port
USB serial device is expected to have two bulk in/out pairs. The Moxa
UPORT only has one pair for data transfer and places a header on each
transfer over the endpoint indicating for which port the transfer
relates to. There is a second endpoint pair for events, such as modem
control lines changing state, setting baud rates etc. Again, a
multiplexing header is used on these endpoints.

Some ports need to have a kfifo explicitly allocated since the
framework does not allocate one if there is no associated endpoints.
The framework will however free it on unload of the module.

All data transfers are made on port0, yet the locks are taken on PortN.
urb->context points to PortN, even though the URB is for port0.

Where possible, code from the generic driver is called. However
mxuport_process_read_urb_data() is mostly a cut/paste of
usb_serial_generic_process_read_urb().

The driver will attempt to load firmware from userspace and compare
the available version and the running version. If the available
version is newer, it will be download into RAM of the device and
started. This is optional and the driver appears to work O.K. with
older firmware in the devices ROM.

This driver is based on the MOXA driver and retains MOXAs copyright.

[jhovold@gmail.com: fix get_fw_version error path and some style issues]

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

USB: serial: move the "simple" drivers into usb-serial-simple.c

Instead of having to create a new driver for a "simple" usb to serial
device, mush them all into one file, with a macro, s

USB: serial: move the "simple" drivers into usb-serial-simple.c

Instead of having to create a new driver for a "simple" usb to serial
device, mush them all into one file, with a macro, so as to make it easy
to add new ones.

Cc: "René Bürgel" <rene.buergel@sohard.de>
Acked-by: Wei Shuai <cpuwolf@gmail.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Acked-by: Frans Klaver <frans.klaver@xsens.com>
Cc: "Wesley W. Terpstra" <w.terpstra@gsi.de>
Cc: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

USB: serial: add driver for Suunto ANT+ USB device

This adds a driver for the Suunto ANT+ USB device, exposing it as a usb
serial device. This lets the userspace "gant" program to talk

USB: serial: add driver for Suunto ANT+ USB device

This adds a driver for the Suunto ANT+ USB device, exposing it as a usb
serial device. This lets the userspace "gant" program to talk to the
device to communicate over the ANT+ protocol to any devices it finds.

Reported-by: Steinar Gunderson <sgunderson@bigfoot.com>
Tested-by: Steinar Gunderson <sgunderson@bigfoot.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

USB: serial: add support Infineon modem USB flashloader driver

If you want to download Infineon modem via USB, this Infineon USB
flashloader driver is required.

Signed-off-by: W

USB: serial: add support Infineon modem USB flashloader driver

If you want to download Infineon modem via USB, this Infineon USB
flashloader driver is required.

Signed-off-by: Wei Shuai <cpuwolf@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

usb-serial: add support for USB Wishbone-serial adapters

Wishbone is an open hardware SoC bus commonly used in FPGA
designs. Bus access can be serialized using the Etherbone
protocol

usb-serial: add support for USB Wishbone-serial adapters

Wishbone is an open hardware SoC bus commonly used in FPGA
designs. Bus access can be serialized using the Etherbone
protocol <http://www.ohwr.org/projects/etherbone-core>.

This driver is intended to be used with devices which attach
their internal Wishbone bus to a USB serial interface using
the Etherbone protocol. A userspace library is required to
speak the protocol made available by this driver as ttyUSBx.

Signed-off-by: Wesley W. Terpstra <w.terpstra@gsi.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

usb: add driver for xsens motion trackers

Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: ezusb: move ezusb.c from drivers/usb/serial to drivers/usb/misc

This patch
- moves drivers/usb/serial/ezusb.c to drivers/usb/misc/
- renamed CONFIG_USB_EZUSB to CONFIG_USB_EZUSB

USB: ezusb: move ezusb.c from drivers/usb/serial to drivers/usb/misc

This patch
- moves drivers/usb/serial/ezusb.c to drivers/usb/misc/
- renamed CONFIG_USB_EZUSB to CONFIG_USB_EZUSB_FX2 to avoid build errors
- adapts Makefiles and Kconfigs switching from bool to tristate for CONFIG_USB_EZUSB_FX2

Signed-off-by: René Bürgel <rene.buergel@sohard.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

USB: serial: remove vizzini driver

It's out-dated for the tty-layer stuff, and would require a bunch of
work. That's not really a big deal, the big issue is that there is no
company

USB: serial: remove vizzini driver

It's out-dated for the tty-layer stuff, and would require a bunch of
work. That's not really a big deal, the big issue is that there is no
company contact for the hardware, so questions we have about it (like
why isn't this just handled by the cdc-acm driver instead?) go
unanswered.

So drop the driver. If someone comes along to help answer the
questions, we can easily revert this and fix up the code.

Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Rob Duncan <rob.duncan@exar.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

USB: serial: add vizzini driver

Here's a driver for the Vizzini USB to serial device.
It looks to be copied from cdc-acm, and probably can be cleaned up a lot
more. Also, there's so

USB: serial: add vizzini driver

Here's a driver for the Vizzini USB to serial device.
It looks to be copied from cdc-acm, and probably can be cleaned up a lot
more. Also, there's some odd "try to grab another interface" that is
probably wrong. And, if this really is a cdc-acm device, it probably
should just be a quirk of the cdc-acm device, but I can't figure that
out, and people have been using this driver for a long time now. So
merge it to let people use their hardware and clean it up over time.

Driver written by Rob Duncan but cleaned up and forward ported to the
latest kernel tree by me.

Cc: Rob Duncan <rob.duncan@exar.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

USB: serial: add zte_ev.c driver

This adds a driver for the zte_ev set of usb to serial devices. It is
based on a patch floating around the internet that modified the generic
usb-se

USB: serial: add zte_ev.c driver

This adds a driver for the zte_ev set of usb to serial devices. It is
based on a patch floating around the internet that modified the generic
usb-serial driver to only work for this type of device.

I've left comments in the code that I think show the data commands being
sent to the device, which I'm guessing come from a usb analyzer. Maybe
they can help others out as well.

Many thanks to nirinA raseliarison for pointing the original patch out
to me, and for testing that the driver works properly.

Tested-by: nirinA raseliarison <nirina.raseliarison@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

USB: serial: add quatech2 usb to serial driver

This supports the Quatech USB 2 usb to serial adapters.

Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kro

USB: serial: add quatech2 usb to serial driver

This supports the Quatech USB 2 usb to serial adapters.

Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

USB: serial: metro-usb: add to the build

This adds the metro-usb driver to the build system properly.

Cc: Aleksey Babahin <tamerlan311@gmail.com>
Signed-off-by: Greg Kroah-Hartm

USB: serial: metro-usb: add to the build

This adds the metro-usb driver to the build system properly.

Cc: Aleksey Babahin <tamerlan311@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

USB: serial: add Fintek F81232 usb to serial driver

This is the first cut at a driver for the Fintek F81232 USB to serial
single port converter. This provides the initial framework for

USB: serial: add Fintek F81232 usb to serial driver

This is the first cut at a driver for the Fintek F81232 USB to serial
single port converter. This provides the initial framework for the
device, and some data can move through it, but no line settings are
handled, so it's not that useful yet. It does give people a starting
place to work from.

Thank to Fintek for providing samples and specifications, without which,
this driver would have never been able to be written.

Cc: Amanda Ying <Amanda_Ying@fintek.com.tw>
Cc: Tom Tsai <Tom_Tsai@fintek.com.tw>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...