[SCSI] lpfc 8.3.45: Incorporated support of a low-latency io path

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.44: Fix kernel panics from corrupted ndlp list

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.40: Update Copyrights to 2013 for 8.3.38, 8.3.39, and 8.3.40 modifications

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@

[SCSI] lpfc 8.3.40: Update Copyrights to 2013 for 8.3.38, 8.3.39, and 8.3.40 modifications

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

show more ...

[SCSI] lpfc 8.3.39: Fixed not returning FAILED status when SCSI invoking host reset handler failed

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBo

[SCSI] lpfc 8.3.39: Fixed not returning FAILED status when SCSI invoking host reset handler failed

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

show more ...

[SCSI] lpfc 8.3.38: Fixed degraded performance after cable pulls

The service parameters for the VPI/RPIs were incorrect, resulting in
lower utilization

Signed-off-by: James Smar

[SCSI] lpfc 8.3.38: Fixed degraded performance after cable pulls

The service parameters for the VPI/RPIs were incorrect, resulting in
lower utilization

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

show more ...

[SCSI] lpfc 8.3.37: Fixed no-context ABTS failed with BA_RJT

Fixed no-context ABTS received on unsolicited receive queue failed with BA_RJT

Signed-off-by: James Smart <james.smart@e

[SCSI] lpfc 8.3.37: Fixed no-context ABTS failed with BA_RJT

Fixed no-context ABTS received on unsolicited receive queue failed with BA_RJT

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

show more ...

[SCSI] lpfc 8.3.36: Fixed boot from san failure

Fixed boot from san failure when SLI4 FC device presented on the same PCI bus

The request_firmware interface can induce delays while

[SCSI] lpfc 8.3.36: Fixed boot from san failure

Fixed boot from san failure when SLI4 FC device presented on the same PCI bus

The request_firmware interface can induce delays while looking
for firmware files, even if no fw file is present. In some situations
the delays exceeded scan_wait timeouts, resulting in situations in which
the boot device had not been discovered in time. Boot Device does not
need to be on a lpfc device.

Change request_firmware use to be module paramater driven. Default is to
not attempt firmware download on boot. Add sysfs parameter to invoke
firmware update.

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

show more ...

[SCSI] lpfc 8.3.35: Fixed not reporting logical link speed to SCSI midlayer when QoS not on

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley

[SCSI] lpfc 8.3.35: Fixed not reporting logical link speed to SCSI midlayer when QoS not on

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

show more ...

[SCSI] lpfc 8.3.34: Add LOGO support after ABTS compliance

Make compliant with FC specs by sending LOGO after ABTS timeouts

Signed-off-by: James Smart <james.smart@emulex.com>
S

[SCSI] lpfc 8.3.34: Add LOGO support after ABTS compliance

Make compliant with FC specs by sending LOGO after ABTS timeouts

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

show more ...

[SCSI] lpfc 8.3.33: Add lpfc_fcp_look_ahead module parameter

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.33: Tie parallel I/O queues into separate MSIX vectors

Add fcp_io_channel module attribute to control amount of parallel I/O queues

Signed-off-by: James Smart <james

[SCSI] lpfc 8.3.33: Tie parallel I/O queues into separate MSIX vectors

Add fcp_io_channel module attribute to control amount of parallel I/O queues

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

show more ...

[SCSI] lpfc 8.3.32: Correct provisioning change failure on local function

Fixed system held-up when performing resource provsion through same PCI
function

Signed-off-by: Alex Ia

[SCSI] lpfc 8.3.32: Correct provisioning change failure on local function

Fixed system held-up when performing resource provsion through same PCI
function

Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

show more ...

[SCSI] lpfc 8.3.31: Fixed system panic due to midlayer abort and driver complete race on SCSI cmd

Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <

[SCSI] lpfc 8.3.31: Fixed system panic due to midlayer abort and driver complete race on SCSI cmd

Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

show more ...

[SCSI] lpfc 8.3.31: Correct handling of SLI4-port XRI resource-provisioning profile change

Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.s

[SCSI] lpfc 8.3.31: Correct handling of SLI4-port XRI resource-provisioning profile change

Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

show more ...

[SCSI] lpfc 8.3.29: SLI related fixes

SLI related fixes:

- Fix REG_RPI fails on SLI4 HBA putting NPort into NPR state (126230)
- Fix ELS FDISC failing with local reject / invali

[SCSI] lpfc 8.3.29: SLI related fixes

SLI related fixes:

- Fix REG_RPI fails on SLI4 HBA putting NPort into NPR state (126230)
- Fix ELS FDISC failing with local reject / invalid RPI. (126350)
- Fix reset port when reset is needed during fw_dump (125807)
- Fix unbounded firmware revision string from port cause panic (126560)
- Fix driver behavior when receiving an ADISC (126654)
- Fix driver not returning when bad ndlp found in abts error event
handling (126209)
- Add more driver logs in area of SLI4 port error attention and reset
recovery (126813, 124466)
- Fix failure in handling large CQ/EQ identifiers in an IOV
environment (126856)
- Fix for driver using duplicate RPIs after lancer port reset (126723)
- Clear vport->fc_myDID in lpfc_els_issue_fdisc to guarentee a
zero SID (126779, 126897)
- Fix for SLI4 Port delivery for BLS ABORT ACC (126289)

Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

show more ...

[SCSI] lpfc 8.3.28: Add Loopback support for SLI4 adapters

- Add Basic support for SLI4 Loopback.
(CR 124951, 125766, 124951, 125843, 125832, 125843)
- Added missing protection in

[SCSI] lpfc 8.3.28: Add Loopback support for SLI4 adapters

- Add Basic support for SLI4 Loopback.
(CR 124951, 125766, 124951, 125843, 125832, 125843)
- Added missing protection in setting/clearing of phba->link_flag bit
field (CR 125994)
- Use link type and link number obtained from READ_CONFIG mailbox
command. (CR 126264)

Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

show more ...

[SCSI] lpfc 8.3.28: Add support for ABTS failure handling

Add support for ABTS failure handling:

- Add asynchronous ABTS notification event feature to driver (CR 124578)
- Chang

[SCSI] lpfc 8.3.28: Add support for ABTS failure handling

Add support for ABTS failure handling:

- Add asynchronous ABTS notification event feature to driver (CR 124578)
- Change driver message 3092 and 3116 to KERN_WARNING (CR 124768)
- Alter the SCR ELS command to use the temporary RPI and the
Destination DID for SLI4-FC (CR 126070)

Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

show more ...

[SCSI] lpfc 8.3.28: SLI fixes and added SLI4 support

Adapter (SLI) interface fixes:

- Modify WQ handling to use entry_repost (CR 123981)
- Fix for ABTS. Do not free original IO

[SCSI] lpfc 8.3.28: SLI fixes and added SLI4 support

Adapter (SLI) interface fixes:

- Modify WQ handling to use entry_repost (CR 123981)
- Fix for ABTS. Do not free original IOCB whenever ABTS fails. (CR 115829)
- Check board for FCoE before reading FCoE paramaters (CR124731)
- Add support for SLI4 FC Loop mode (CR 124721)
- Add support for resource count changes during fw reset. (CR 125888, 125675)
- Increase CQE count from 256 to 1024. (CR 126149)

Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

show more ...

[SCSI] lpfc 8.3.28: Miscellaneous fixes in sysfs and mgmt interfaces

Miscellaneous fixes in sysfs and mgmt interfaces:

- Added SLI4 INTF_TYPE and SLI_FAMILY as sub-field to the fwre

[SCSI] lpfc 8.3.28: Miscellaneous fixes in sysfs and mgmt interfaces

Miscellaneous fixes in sysfs and mgmt interfaces:

- Added SLI4 INTF_TYPE and SLI_FAMILY as sub-field to the fwrev sysfs
attribute (CR 124103)
- Added a sysfs attribute "protocol" to report SLI4 port link protocol
type (CR 124102)
- Increment mix-and-match minor number by 1 for added "protocol" sysfs
attribute. (124102)
- Move the link speed check into the generic sli3/sli4 code
path. (CR 124185, 124122)
- Deleted check for inExtWLen (CR 122523)
- Add the word "offline" to message 2889 (CR 124385)
- Conditionalize the firmware upgrade/downgrade so that it is only
attempted for SLI4 type 2 boards (CR 124406)
- Return an error if the mbox sysfs is called. (CR 124210)
- When port_state is less than LPFC_VPORT_READY, report
FC_PORTSTATE_BYPASSED (CR 120018)
- Added driver support for performing persistent linkdown based on
configure region 23 (CR 124534)
- Added restore state and error log when sysfs board_mode attribute
access failed (CR 124158)
- Added support for SLI4_CONFIG non-embedded COMN_GET_CNTL_ADDL_ATTR
pass-through (CR 124466)
- Rejecting un-supported multi-buffer mailbox commands (CR 124771)
- Byte swap the extended data request and response data for extended
mailbox data (CR 125081)

Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

show more ...

[SCSI] lpfc 8.3.27: Fix queue allocation failure recovery

Fix queue allocation failure recovery

- Move the allocation of the Queues closer to the creation of the queues.
- If th

[SCSI] lpfc 8.3.27: Fix queue allocation failure recovery

Fix queue allocation failure recovery

- Move the allocation of the Queues closer to the creation of the queues.
- If there is a problem with creation, or if the HBA is reset, the queues
will be completely freed and re allocated.
- Only allocate fcp_eq_hdl if cfg_fcp_eq_count is non-zero.

Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

show more ...

[SCSI] lpfc 8.3.27: Changed worst case mailbox timeout

Changed the timeout value for flash-based SLI_CONFIG (0x9B)
mailbox command to 300 seconds for worst case flash delays.

Si

[SCSI] lpfc 8.3.27: Changed worst case mailbox timeout

Changed the timeout value for flash-based SLI_CONFIG (0x9B)
mailbox command to 300 seconds for worst case flash delays.

Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

show more ...

[SCSI] lpfc 8.3.25: Add FCF priority failover functionality

This patch implements a new FCF failover policy for the lpfc driver. It
allows the driver to choose which FCF to failover to b

[SCSI] lpfc 8.3.25: Add FCF priority failover functionality

This patch implements a new FCF failover policy for the lpfc driver. It
allows the driver to choose which FCF to failover to based on the FCF
priority. This patch also introduces a new sysfs parameter
(fcf_failover_policy) to allow the user to choose which FCF failover policy
to use.

Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

show more ...

[SCSI] lpfc 8.3.25: Enhancements to Debug infrastructure

Enhancements to Debug infrastructure

- debugfs additions for new hardware.
- Correct stack overflow in lpfc_debugfs_dump

[SCSI] lpfc 8.3.25: Enhancements to Debug infrastructure

Enhancements to Debug infrastructure

- debugfs additions for new hardware.
- Correct stack overflow in lpfc_debugfs_dumpHBASlim_data()
- Correct warning on uninitialized reg_val in lpfc_idiag_drbacc_write()
- Separated the iDiag command for capturing mailbox commands for generic
issue mailbox command entry point and for BSG multi-buffer handling.
- Added capturing dumping capabiliy of mailbox command and external buffer
for the completion of the mailbox command so that the outcome can be
examined.
- Changed all the iDiag command structure data array indexing introduced so
far with properly defined macros.
- Added SLI4 device PCI BAR memory mapped register read/browse, write-by-
value, set-bit, and clear-bit methods for both interface type 0 and
interface type 2.
- Corrected warnings on mbxstatus being uninitialized in error paths in
lpfc_bsg.c

Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

show more ...

[SCSI] lpfc 8.3.25: PCI and SR-IOV Fixes

PCI and SR-IOV Fixes

- Call pci_save_state after the pci_restore_state completes.
- After calling pci_enable_pcie_error_reporting() and

[SCSI] lpfc 8.3.25: PCI and SR-IOV Fixes

PCI and SR-IOV Fixes

- Call pci_save_state after the pci_restore_state completes.
- After calling pci_enable_pcie_error_reporting() and checking the return
value for logging messages from rc, reset rc to 0 to it will not later be
interpreted for error.
- Read PCI config space SR-IOV capability to get the number of VFs supported.
- Check for the PF's supported number of VFs before invoking PCI enable sriov
API call and log error message that user requested number of VFs is beyond
the PF capability if such request is passed in.
- Added check for Physical function with Virtual Functions attached. If so,
first disable all the VFs before proceeding to device reset.

Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

show more ...

[SCSI] lpfc 8.3.25: Adapter Interface fixes and changes

Adapter Interface fixes and changes

- Modify the macro field from lpfc_init_vpi_vpi to lpfc_init_vfi_vpi
- Add the new CQ

[SCSI] lpfc 8.3.25: Adapter Interface fixes and changes

Adapter Interface fixes and changes

- Modify the macro field from lpfc_init_vpi_vpi to lpfc_init_vfi_vpi
- Add the new CQE_CODE_RECEIVE_V1 CQE Code, add code in the driver to handle
the new Code the same as the CQE_CODE_RECEIVE code except that there are
two new checks for this code that will cause the driver to use the new V1
macros for rq_id and fcf_id.
- Fix a bug in lpfc_prep_seq() where the size out of the first CQE was
ONLY being used, even though multiple dmabufs make up the sequence,
each have their own CQE with potentially different sizes.
- Fix bug in lpfc_bsg_ct_unsol_event() where the ulpContext and ulpWord[3]
fields of the XMIT_SEQUENCE64_CX IOCB were being calculated incorrectly.
- Do physical to logical translation before indexing into the active
XRI array.
- Populate physical vpi in the iocb data structure.
- Put the current accumulated total in each IOCB in the chain as we are
walking thru then. The last IOCB in the chain should have the total
length of the sequence.

Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

show more ...