pwm: lpss: platform: Save/restore the ctrl register over a suspend/resume

On some devices the contents of the ctrl register get lost over a
suspend/resume and the PWM comes back up disab

pwm: lpss: platform: Save/restore the ctrl register over a suspend/resume

On some devices the contents of the ctrl register get lost over a
suspend/resume and the PWM comes back up disabled after the resume.

This is seen on some Bay Trail devices with the PWM in ACPI enumerated
mode, so it shows up as a platform device instead of a PCI device.

If we still think it is enabled and then try to change the duty-cycle
after this, we end up with a "PWM_SW_UPDATE was not cleared" error and
the PWM is stuck in that state from then on.

This commit adds suspend and resume pm callbacks to the pwm-lpss-platform
code, which save/restore the ctrl register over a suspend/resume, fixing
this.

Note that:

1) There is no need to do this over a runtime suspend, since we
only runtime suspend when disabled and then we properly set the enable
bit and reprogram the timings when we re-enable the PWM.

2) This may be happening on more systems then we realize, but has been
covered up sofar by a bug in the acpi-lpss.c code which was save/restoring
the regular device registers instead of the lpss private registers due to
lpss_device_desc.prv_offset not being set. This is fixed by a later patch
in this series.

Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

show more ...

pwm: lpss: Set enable-bit before waiting for update-bit to go low

At least on cherrytrail, the update bit will never go low when the
enabled bit is not set.

This causes the back

pwm: lpss: Set enable-bit before waiting for update-bit to go low

At least on cherrytrail, the update bit will never go low when the
enabled bit is not set.

This causes the backlight on my cube iwork8 air tablet to never turn on
again after being turned off because in the pwm_lpss_apply enable path
pwm_lpss_update will fail causing an error exit and the enable-bit to
never get set. Any following pwm_lpss_apply calls will fail the
pwm_lpss_is_updating check.

Since the docs say that the update bit should be set before the
enable-bit, split pwm_lpss_update into setting the update-bit and
pwm_lpss_wait_for_update, and move the pwm_lpss_wait_for_update call
in the enable path to after setting the enable-bit.

Fixes: 10d56a4 ("pwm: lpss: Avoid reconfiguring while UPDATE bit...")
Cc: Ilkka Koskinen <ilkka.koskinen@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

show more ...

pwm: lpss: Do not export board infos for different PWM types

The PWM LPSS probe drivers just pass a pointer to the exported board
info structures to pwm_lpss_probe() based on device PCI

pwm: lpss: Do not export board infos for different PWM types

The PWM LPSS probe drivers just pass a pointer to the exported board
info structures to pwm_lpss_probe() based on device PCI or ACPI ID.

In order to remove the knowledge of specific devices from library part of
the driver and reduce noise in exported namespace just duplicate the
board info structures and stop exporting them.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

show more ...

pwm: lpss: Add support for runtime PM

To be able to save some power when PWM is not in use, add support for
runtime PM for this driver. This also allows the platform to transition to

pwm: lpss: Add support for runtime PM

To be able to save some power when PWM is not in use, add support for
runtime PM for this driver. This also allows the platform to transition to
low power S0ix states when the system is idle.

Signed-off-by: Huiquan Zhong <huiquan.zhong@intel.com>
Signed-off-by: Qipeng Zha <qipeng.zha@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

show more ...

pwm: lpss: Add more Intel Broxton IDs

Add more Intel Broxton ACPI and PCI IDs to the driver supported devices
list.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.c

pwm: lpss: Add more Intel Broxton IDs

Add more Intel Broxton ACPI and PCI IDs to the driver supported devices
list.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

show more ...

pwm: lpss: Properly split driver to parts

The driver consists of core, PCI, and platform parts. It would be better
to split them into separate files.

The platform driver is now

pwm: lpss: Properly split driver to parts

The driver consists of core, PCI, and platform parts. It would be better
to split them into separate files.

The platform driver is now called pwm-lpss-platform. Thus, previously
set CONFIG_PWM_LPSS=m is not enough to build it. But we are on the safe
side since it seems no one from outside Intel is using it for now.

While here, move to use macros module_pci_driver() and
module_platform_driver().

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Alan Cox <alan@linux.intel.com>
[thierry.reding: change select to depends on PWM_LPSS, cleanup]
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

show more ...