phy: amlogic: add Amlogic G12A USB2 PHY Driver

This adds support for the USB2 PHY found in the Amlogic G12A SoC Family.

It supports Host and/or Peripheral mode, depending on it's po

phy: amlogic: add Amlogic G12A USB2 PHY Driver

This adds support for the USB2 PHY found in the Amlogic G12A SoC Family.

It supports Host and/or Peripheral mode, depending on it's position.
The first PHY is only used as Host, but the second supports Dual modes
defined by the USB Control Glue HW in front of the USB Controllers.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

show more ...

phy: amlogic: add USB3 PHY support for Meson GXL and GXM

This adds a new driver for the USB3 PHY found on Meson GXL and GXM SoCs
(both SoCs are using the same USB PHY register layout).

phy: amlogic: add USB3 PHY support for Meson GXL and GXM

This adds a new driver for the USB3 PHY found on Meson GXL and GXM SoCs
(both SoCs are using the same USB PHY register layout).

Unfortunately there is no documentation for this PHY in the public S905X
datasheet (published for example by Khadas). What we know so far about
this PHY:
- even though the Meson GXL and GXM SoCs do not expose an USB3 port (the
dwc3 controller only has USB2 ports enabled) we need to initialize the
USB3 PHY (specifically USB_R1_U3H_FLADJ_30MHZ_REG_MASK). Without this
initialization high-speed USB devices (especially USB hard disks and
thumb drives, slower devices like mice do not seem to be affected)
- on some boards the USB3 PHY starts in "device mode" - we want to bring
it into a known state (by switching it to host mode for now).
- it is responsible for the OTG detection and for switching the first
USB2 PHY between host and peripheral (aka device) mode. an interrupt
can be used to detect changes between host and device mode.

There are five inputs to this register area:
- the clock and reset line for the USB3 PHY itself
- the clock and reset line for the peripheral mode and OTG detection
logic (on the GXL and GXM SoCs these are the same clock and reset line
as for the USB3 PHY itself, but Amlogic sees this as two different
components - even though they share the same register space - so they
have to be passed individually to allow specifying different inputs on
other SoCs if needed)
- the interrupt for the OTG detection logic

The whole OTG detection logic is not implemented yet.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Yixun Lan <yixun.lan@amlogic.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

show more ...

phy: amlogic: phy-meson-gxl-usb2: default to host mode

The USB2 PHY can switch between PHY_MODE_USB_HOST and
PHY_MODE_USB_DEVICE. However, it cannot do it on it's own since it
requir

phy: amlogic: phy-meson-gxl-usb2: default to host mode

The USB2 PHY can switch between PHY_MODE_USB_HOST and
PHY_MODE_USB_DEVICE. However, it cannot do it on it's own since it
requires re-routing of the corresponding USB pins from dwc3 (which is
used for host-mode) to dwc2 (which is used for device-mode).
Thus we don't need to auto-detect the mode based on the USB controller,
which simplifies the driver code.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

show more ...

phy: meson8b-usb2: add support for the USB PHY on Meson8 SoCs

Meson8 uses the same USB PHY as found on the Meson8b and GXBB SoCs. Add
a new of_device_id to indicate this. Also update the

phy: meson8b-usb2: add support for the USB PHY on Meson8 SoCs

Meson8 uses the same USB PHY as found on the Meson8b and GXBB SoCs. Add
a new of_device_id to indicate this. Also update the Kconfig option and
MODULE_DESCRIPTION accordingly.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

show more ...

phy: meson: add USB2 PHY support for Meson GXL and GXM

This adds a new driver for the USB2 PHYs found on Meson GXL and GXM SoCs
(both SoCs are using the same USB PHY register layout).

phy: meson: add USB2 PHY support for Meson GXL and GXM

This adds a new driver for the USB2 PHYs found on Meson GXL and GXM SoCs
(both SoCs are using the same USB PHY register layout).

The USB2 PHY is a simple PHY which only has a few registers to configure
the mode (host/device) and a reset register (to enable/disable the PHY).

Unfortunately there are no datasheets available for this PHY. The driver
was written by reading the code from Amlogic's GPL kernel sources and
by analyzing the registers on an actual GXL and GXM device running the
kernel that was shipped on the boards I have.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

show more ...

phy: Group vendor specific phy drivers

Adding vendor specific directories in phy to group
phy drivers under their respective vendor umbrella.

Also updated the MAINTAINERS file t

phy: Group vendor specific phy drivers

Adding vendor specific directories in phy to group
phy drivers under their respective vendor umbrella.

Also updated the MAINTAINERS file to reflect the correct
directory structure for phy drivers.

Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Stephen Boyd <stephen.boyd@linaro.org>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

show more ...