net: sfp: VSOL V2801F / CarlitoxxPro CPGOS03-0490 v2.0 workaround

Add a workaround for the detection of VSOL V2801F / CarlitoxxPro
CPGOS03-0490 v2.0 GPON module which CarlitoxxPro states needs singl

net: sfp: VSOL V2801F / CarlitoxxPro CPGOS03-0490 v2.0 workaround

Add a workaround for the detection of VSOL V2801F / CarlitoxxPro
CPGOS03-0490 v2.0 GPON module which CarlitoxxPro states needs single
byte I2C reads to the EEPROM.

Pali Rohár reports that he also has a CarlitoxxPro-based V2801F module,
which reports a manufacturer of "OEM". This manufacturer can't be
matched as it appears in many different modules, so also match the part
number too.

Reported-by: Thomas Schreiber <tschreibe@gmail.com>
Reported-by: Pali Rohár <pali@kernel.org>
Tested-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: sfp: cope with SFPs that set both LOS normal and LOS inverted

commit 624407d2cf14ff58e53bf4b2af9595c4f21d606e upstream.

The SFP MSA defines two option bits in byte 65 to indicate how the
Rx_LO

net: sfp: cope with SFPs that set both LOS normal and LOS inverted

commit 624407d2cf14ff58e53bf4b2af9595c4f21d606e upstream.

The SFP MSA defines two option bits in byte 65 to indicate how the
Rx_LOS signal on SFP pin 8 behaves:

bit 2 - Loss of Signal implemented, signal inverted from standard
definition in SFP MSA (often called "Signal Detect").
bit 1 - Loss of Signal implemented, signal as defined in SFP MSA
(often called "Rx_LOS").

Clearly, setting both bits results in a meaningless situation: it would
mean that LOS is implemented in both the normal sense (1 = signal loss)
and inverted sense (0 = signal loss).

Unfortunately, there are modules out there which set both bits, which
will be initially interpret as "inverted" sense, and then, if the LOS
signal changes state, we will toggle between LINK_UP and WAIT_LOS
states.

Change our LOS handling to give well defined behaviour: only interpret
these bits as meaningful if exactly one is set, otherwise treat it as
if LOS is not implemented.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1kyYQa-0004iR-CU@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cc: Pali Rohár <pali@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

net: sfp: add workaround for Realtek RTL8672 and RTL9601C chips

[ Upstream commit 426c6cbc409cbda9ab1a9dbf15d3c2ef947eb8c1 ]

The workaround for VSOL V2801F brand based GPON SFP modules added in com

net: sfp: add workaround for Realtek RTL8672 and RTL9601C chips

[ Upstream commit 426c6cbc409cbda9ab1a9dbf15d3c2ef947eb8c1 ]

The workaround for VSOL V2801F brand based GPON SFP modules added in commit
0d035bed2a4a ("net: sfp: VSOL V2801F / CarlitoxxPro CPGOS03-0490 v2.0
workaround") works only for IDs added explicitly to the list. Since there
are rebranded modules where OEM vendors put different strings into the
vendor name field, we cannot base workaround on IDs only.

Moreover the issue which the above mentioned commit tried to work around is
generic not only to VSOL based modules, but rather to all GPON modules
based on Realtek RTL8672 and RTL9601C chips.

These include at least the following GPON modules:
* V-SOL V2801F
* C-Data FD511GX-RM0
* OPTON GP801R
* BAUDCOM BD-1234-SFM
* CPGOS03-0490 v2.0
* Ubiquiti U-Fiber Instant
* EXOT EGS1

These Realtek chips have broken EEPROM emulator which for N-byte read
operation returns just the first byte of EEPROM data, followed by N-1
zeros.

Introduce a new function, sfp_id_needs_byte_io(), which detects SFP modules
with broken EEPROM emulator based on N-1 zeros and switch to 1 byte EEPROM
reading operation.

Function sfp_i2c_read() now always uses single byte reading when it is
required and when function sfp_hwmon_probe() detects single byte access,
it disables registration of hwmon device, because in this case we cannot
reliably and atomically read 2 bytes as is required by the standard for
retrieving values from diagnostic area.

(These Realtek chips are broken in a way that violates SFP standards for
diagnostic interface. Kernel in this case simply cannot do anything less
of skipping registration of the hwmon interface.)

This patch fixes reading of EEPROM content from SFP modules based on
Realtek RTL8672 and RTL9601C chips. Diagnostic interface of EEPROM stays
broken and cannot be fixed.

Fixes: 0d035bed2a4a ("net: sfp: VSOL V2801F / CarlitoxxPro CPGOS03-0490 v2.0 workaround")
Co-developed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

net: sfp: VSOL V2801F / CarlitoxxPro CPGOS03-0490 v2.0 workaround

[ Upstream commit 0d035bed2a4a6c4878518749348be61bf082d12a ]

Add a workaround for the detection of VSOL V2801F / CarlitoxxPro
CPGOS

net: sfp: VSOL V2801F / CarlitoxxPro CPGOS03-0490 v2.0 workaround

[ Upstream commit 0d035bed2a4a6c4878518749348be61bf082d12a ]

Add a workaround for the detection of VSOL V2801F / CarlitoxxPro
CPGOS03-0490 v2.0 GPON module which CarlitoxxPro states needs single
byte I2C reads to the EEPROM.

Pali Rohár reports that he also has a CarlitoxxPro-based V2801F module,
which reports a manufacturer of "OEM". This manufacturer can't be
matched as it appears in many different modules, so also match the part
number too.

Reported-by: Thomas Schreiber <tschreibe@gmail.com>
Reported-by: Pali Rohár <pali@kernel.org>
Tested-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

net: sfp: add mode quirk for GPON module Ubiquiti U-Fiber Instant

[ Upstream commit f0b4f847673299577c29b71d3f3acd3c313d81b7 ]

The Ubiquiti U-Fiber Instant SFP GPON module has nonsensical informati

net: sfp: add mode quirk for GPON module Ubiquiti U-Fiber Instant

[ Upstream commit f0b4f847673299577c29b71d3f3acd3c313d81b7 ]

The Ubiquiti U-Fiber Instant SFP GPON module has nonsensical information
stored in its EEPROM. It claims to support all transceiver types including
10G Ethernet. Clear all claimed modes and set only 1000baseX_Full, which is
the only one supported.

This module has also phys_id set to SFF, and the SFP subsystem currently
does not allow to use SFP modules detected as SFFs. Add exception for this
module so it can be detected as supported.

This change finally allows to detect and use SFP GPON module Ubiquiti
U-Fiber Instant on Linux system.

EEPROM content of this SFP module is (where XX is serial number):

00: 02 04 0b ff ff ff ff ff ff ff ff 03 0c 00 14 c8 ???........??.??
10: 00 00 00 00 55 42 4e 54 20 20 20 20 20 20 20 20 ....UBNT
20: 20 20 20 20 00 18 e8 29 55 46 2d 49 4e 53 54 41 .??)UF-INSTA
30: 4e 54 20 20 20 20 20 20 34 20 20 20 05 1e 00 36 NT 4 ??.6
40: 00 06 00 00 55 42 4e 54 XX XX XX XX XX XX XX XX .?..UBNTXXXXXXXX
50: 20 20 20 20 31 34 30 31 32 33 20 20 60 80 02 41 140123 `??A

Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

sfp: Fix error handing in sfp_probe()

gpiod_to_irq() never return 0, but returns negative in
case of error, check it and set gpio_irq to 0.

Fixes: 73970055450e ("sfp: add SFP module support")
Signe

sfp: Fix error handing in sfp_probe()

gpiod_to_irq() never return 0, but returns negative in
case of error, check it and set gpio_irq to 0.

Fixes: 73970055450e ("sfp: add SFP module support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201031031053.25264-1-yuehaibing@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

net/phy/mdio-i2c: Move header file to include/linux/mdio

In preparation for moving all MDIO drivers into drivers/net/mdio, move
the mdio-i2c header file into include/linux/mdio so it can be used by

net/phy/mdio-i2c: Move header file to include/linux/mdio

In preparation for moving all MDIO drivers into drivers/net/mdio, move
the mdio-i2c header file into include/linux/mdio so it can be used by
both the MDIO driver and the SFP code which instantiates I2C MDIO
busses.

v2:
Add include/linux/mdio

Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

treewide: Use fallthrough pseudo-keyword

Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through mar

treewide: Use fallthrough pseudo-keyword

Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.

[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through

Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>

show more ...

net: phy: sfp: Cotsworks SFF module EEPROM fixup

Some Cotsworks SFF have invalid data in the first few bytes of the
module EEPROM. This results in these modules not being detected as
valid modules.

net: phy: sfp: Cotsworks SFF module EEPROM fixup

Some Cotsworks SFF have invalid data in the first few bytes of the
module EEPROM. This results in these modules not being detected as
valid modules.

Address this by poking the correct EEPROM values into the module
EEPROM when the model/PN match and the existing module EEPROM contents
are not correct.

Signed-off-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: sfp: add error checking with sfp_irq_name

Add error checking with sfp_irq_name before use.

Signed-off-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sfp: Unique GPIO interrupt names

Dynamically generate a unique GPIO interrupt name, based on the
device name and the GPIO name. For example:

103: 0 sx1503q 12 Edge sff2-los
1

net: sfp: Unique GPIO interrupt names

Dynamically generate a unique GPIO interrupt name, based on the
device name and the GPIO name. For example:

103: 0 sx1503q 12 Edge sff2-los
104: 0 sx1503q 13 Edge sff2-tx-fault

The sffX indicates the SFP the los and tx-fault are associated with.

v3:
- reverse Christmas tree new variable
- fix spaces vs tabs
v2:
- added net-next to PATCH part of subject line
- switched to devm_kasprintf()

Signed-off-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: sfp: report error on failure to read sfp soft status

Report a rate-limited error if we fail to read the SFP soft status,
and preserve the current status in that case. This avoids I2C bus
errors

net: sfp: report error on failure to read sfp soft status

Report a rate-limited error if we fail to read the SFP soft status,
and preserve the current status in that case. This avoids I2C bus
errors from triggering a link flap.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: sfp: re-attempt probing for phy

Some 1000BASE-T PHY modules take a while for the PHY to wake up.
Retry the probe a number of times before deciding that the module has
no PHY.

Tested with:
Sou

net: sfp: re-attempt probing for phy

Some 1000BASE-T PHY modules take a while for the PHY to wake up.
Retry the probe a number of times before deciding that the module has
no PHY.

Tested with:
Sourcephotonics SPGBTXCNFC - PHY takes less than 50ms to respond.
Champion One 1000SFPT - PHY takes about 200ms to respond.
Mikrotik S-RJ01 - no PHY

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: sfp: error handling for phy probe

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sfp: rename sm_retries

Rename sm_retries as sm_fault_retries, as this is what this member is
tracking.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew

net: sfp: rename sm_retries

Rename sm_retries as sm_fault_retries, as this is what this member is
tracking.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: sfp: use a definition for the fault recovery attempts

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@da

net: sfp: use a definition for the fault recovery attempts

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: sfp: add support for Clause 45 PHYs

Some SFP+ modules have a Clause 45 PHY onboard, which is accessible via
the normal I2C address. Detect 10G BASE-T PHYs which may have an
accessible PHY and

net: sfp: add support for Clause 45 PHYs

Some SFP+ modules have a Clause 45 PHY onboard, which is accessible via
the normal I2C address. Detect 10G BASE-T PHYs which may have an
accessible PHY and probe for it.

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: sfp: move phy_start()/phy_stop() to phylink

Move phy_start() and phy_stop() into the module_start and module_stop
notifications in phylink, rather than having them in the SFP code.
This gives p

net: sfp: move phy_start()/phy_stop() to phylink

Move phy_start() and phy_stop() into the module_start and module_stop
notifications in phylink, rather than having them in the SFP code.
This gives phylink responsibility for controlling the PHY, rather
than having SFP start and stop the PHY state machine.

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: sfp: add module start/stop upstream notifications

When dealing with some copper modules, we can't positively know the
module capabilities are until we have probed the PHY. Without the full
capa

net: sfp: add module start/stop upstream notifications

When dealing with some copper modules, we can't positively know the
module capabilities are until we have probed the PHY. Without the full
capabilities, we may end up failing a module that we could otherwise
drive with a restricted set of capabilities.

An example of this would be a module with a NBASE-T PHY plugged into
a host that supports phy interface modes 2500BASE-X and SGMII. The
PHY supports 10GBASE-R, 5000BASE-X, 2500BASE-X, SGMII interface modes,
which means a subset of the capabilities are compatible with the host.

However, reading the module EEPROM leads us to believe that the module
only supports ethtool link mode 10GBASE-T, which is incompatible with
the host - and thus results in the module being rejected.

This patch adds an extra notification which are triggered after the
SFP module's PHY probe, and a corresponding notification just before
the PHY is removed.

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: sfp: add more extended compliance codes

SFF-8024 is used to define various constants re-used in several SFF
SFP-related specifications. Split these constants from the enum, and
rename them to

net: sfp: add more extended compliance codes

SFF-8024 is used to define various constants re-used in several SFF
SFP-related specifications. Split these constants from the enum, and
rename them to indicate that they're defined by SFF-8024.

Add and use updated SFF-8024 extended compliance code definitions for
10GBASE-T, 5GBASE-T and 2.5GBASE-T modules.

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: sfp: remove incomplete 100BASE-FX and 100BASE-LX support

The 100BASE-FX and 100BASE-LX support assumes a PHY is present; this
is probably an incorrect assumption. In any case, sfp_parse_support

net: sfp: remove incomplete 100BASE-FX and 100BASE-LX support

The 100BASE-FX and 100BASE-LX support assumes a PHY is present; this
is probably an incorrect assumption. In any case, sfp_parse_support()
will fail such a module. Let's stop pretending we support these
modules.

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: sfp: avoid tx-fault with Nokia GPON module

The Nokia GPON module can hold tx-fault active while it is initialising
which can take up to 60s. Avoid this causing the module to be declared
faulty

net: sfp: avoid tx-fault with Nokia GPON module

The Nokia GPON module can hold tx-fault active while it is initialising
which can take up to 60s. Avoid this causing the module to be declared
faulty after the SFP MSA defined non-cooled module timeout.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: sfp: fix hwmon

The referenced commit below allowed more than one hwmon device to be
created per SFP, which is definitely not what we want. Avoid this by
only creating the hwmon device just as w

net: sfp: fix hwmon

The referenced commit below allowed more than one hwmon device to be
created per SFP, which is definitely not what we want. Avoid this by
only creating the hwmon device just as we transition to WAITDEV state.

Fixes: 139d3a212a1f ("net: sfp: allow modules with slow diagnostics to probe")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: sfp: fix unbind

When unbinding, we don't correctly tear down the module state, leaving
(for example) the hwmon registration behind. Ensure everything is
properly removed by sending a remove eve

net: sfp: fix unbind

When unbinding, we don't correctly tear down the module state, leaving
(for example) the hwmon registration behind. Ensure everything is
properly removed by sending a remove event at unbind.

Fixes: 6b0da5c9c1a3 ("net: sfp: track upstream's attachment state in state machine")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: sfp: soft status and control support

Add support for the soft status and control register, which allows
TX_FAULT and RX_LOS to be monitored and TX_DISABLE to be set. We
make use of this when t

net: sfp: soft status and control support

Add support for the soft status and control register, which allows
TX_FAULT and RX_LOS to be monitored and TX_DISABLE to be set. We
make use of this when the board does not support GPIOs for these
signals.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...