net: stmmac: fix disabling flexible PPS output

Accordingly to Synopsys documentation [1] and [2], when bit PPSEN0
in register MAC_PPS_CONTROL is set it selects the functionality
comm

net: stmmac: fix disabling flexible PPS output

Accordingly to Synopsys documentation [1] and [2], when bit PPSEN0
in register MAC_PPS_CONTROL is set it selects the functionality
command in the same register, otherwise selects the functionality
control.
Command functionality is required to either enable (command 0x2)
and disable (command 0x5) the flexible PPS output, but the bit
PPSEN0 is currently set only for enabling.

Set the bit PPSEN0 to properly disable flexible PPS output.

Tested on STM32MP15x, based on dwmac 4.10a.

[1] DWC Ethernet QoS Databook 4.10a October 2014
[2] DWC Ethernet QoS Databook 5.00a September 2017

Signed-off-by: Antonio Borneo <antonio.borneo@st.com>
Fixes: 9a8a02c9d46d ("net: stmmac: Add Flexible PPS support")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

show more ...

net: stmmac: Add Flexible PPS support

This adds support for Flexible PPS output (which is equivalent
to per_out output of PTP subsystem).

Tested using an oscilloscope and the fo

net: stmmac: Add Flexible PPS support

This adds support for Flexible PPS output (which is equivalent
to per_out output of PTP subsystem).

Tested using an oscilloscope and the following commands:

1) Start PTP4L:
# ptp4l -A -4 -H -m -i eth0 &
2) Set Flexible PPS frequency:
# echo <idx> <ts> <tns> <ps> <pns> > /sys/class/ptp/ptpX/period

Where, ts/tns is start time and ps/pns is period time, and ptpX is ptp
of eth0.

Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: stmmac: Add support for U32 TC filter using Flexible RX Parser

This adds support for U32 filter by using an HW only feature called
Flexible RX Parser. This allow us to match any giv

net: stmmac: Add support for U32 TC filter using Flexible RX Parser

This adds support for U32 filter by using an HW only feature called
Flexible RX Parser. This allow us to match any given packet field with a
pattern and accept/reject or even route the packet to a specific DMA
channel.

Right now we only support acception or rejection of frame and we only
support simple rules. Though, the Parser has the flexibility of jumping to
specific rules as an if condition so complex rules can be established.

This is only supported in GMAC5.10+.

The following commands can be used to test this code:

1) Setup an ingress qdisk:
# tc qdisc add dev eth0 handle ffff: ingress

2) Setup a filter (e.g. filter by IP):
# tc filter add dev eth0 parent ffff: protocol ip u32 match ip \
src 192.168.0.3 skip_sw action drop

In every tests performed we always used the "skip_sw" flag to make sure
only the RX Parser was involved.

Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: stmmac: Switch stmmac_ops to generic HW Interface Helpers

Switch stmmac_ops to generic Hardware Interface Helpers instead of using
hard-coded callbacks. This makes the code more rea

net: stmmac: Switch stmmac_ops to generic HW Interface Helpers

Switch stmmac_ops to generic Hardware Interface Helpers instead of using
hard-coded callbacks. This makes the code more readable and more
flexible.

No functional change.

Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: stmmac: Add support for DWMAC5 and implement Safety Features

This adds initial suport for DWMAC5 and implements the Automotive Safety
Package which is available from core version 5.

net: stmmac: Add support for DWMAC5 and implement Safety Features

This adds initial suport for DWMAC5 and implements the Automotive Safety
Package which is available from core version 5.10.

The Automotive Safety Pacakge (also called Safety Features) offers us
with error protection in the core by implementing ECC Protection in
memories, on-chip data path parity protection, FSM parity and timeout
protection and Application/CSR interface timeout protection.

In case of an uncorrectable error we call stmmac_global_err() and
reconfigure the whole core.

Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...