ice: split ice_ring onto Tx/Rx separate structs

While it was convenient to have a generic ring structure that served
both Tx and Rx sides, next commits are going to introduce several
Tx-specific fie

ice: split ice_ring onto Tx/Rx separate structs

While it was convenient to have a generic ring structure that served
both Tx and Rx sides, next commits are going to introduce several
Tx-specific fields, so in order to avoid hurting the Rx side, let's
pull out the Tx ring onto new ice_tx_ring and ice_rx_ring structs.

Rx ring could be handled by the old ice_ring which would reduce the code
churn within this patch, but this would make things asymmetric.

Make the union out of the ring container within ice_q_vector so that it
is possible to iterate over newly introduced ice_tx_ring.

Remove the @size as it's only accessed from control path and it can be
calculated pretty easily.

Change definitions of ice_update_ring_stats and
ice_fetch_u64_stats_per_ring so that they are ring agnostic and can be
used for both Rx and Tx rings.

Sizes of Rx and Tx ring structs are 256 and 192 bytes, respectively. In
Rx ring xdp_rxq_info occupies its own cacheline, so it's the major
difference now.

Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

show more ...

ice: switchdev slow path

Slow path means allowing packet to go from uplink to representor
and from representor to correct VF on Rx site and from VF to
representor and to uplink on Tx site.

To accom

ice: switchdev slow path

Slow path means allowing packet to go from uplink to representor
and from representor to correct VF on Rx site and from VF to
representor and to uplink on Tx site.

To accomplish this driver, has to set correct Tx descriptor. When
packet is sent from representor to VF, destination should be
set to VF VSI. When packet is sent from uplink port destination
should be uplink to bypass switch infrastructure and send packet
outside.

On Rx site driver should check source VSI field from Rx descriptor
and based on that forward packed to correct netdev. To allow
this there is a target netdevs table in control plane VSI
struct.

Co-developed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

show more ...

ice: Add DSCP support

Implement code to handle submission of APP TLV's
containing DSCP to TC mapping.

The first such mapping received on an interface
will cause that PF to switch to L3 DSCP QoS mod

ice: Add DSCP support

Implement code to handle submission of APP TLV's
containing DSCP to TC mapping.

The first such mapping received on an interface
will cause that PF to switch to L3 DSCP QoS mode,
apply the default config for that mode, and apply
the received mapping.

Only one such mapping will be allowed per DSCP value,
and when the last DSCP mapping is deleted, the PF
will switch back into L2 VLAN QoS mode, applying the
appropriate default QoS settings.

L3 DSCP QoS mode will only be allowed in SW DCBx
mode, in other words, when the FW LLDP engine is
disabled. Commands that break this mutual exclusivity
will be blocked.

Co-developed-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

show more ...

ice: add tracepoints

This patch is modeled after one by Scott Peterson for i40e.

Add tracepoints to the driver, via a new file ice_trace.h and some new
trace calls added in interesting places in th

ice: add tracepoints

This patch is modeled after one by Scott Peterson for i40e.

Add tracepoints to the driver, via a new file ice_trace.h and some new
trace calls added in interesting places in the driver. Add some tracing
for DIMLIB to help debug interrupt moderation problems.

Performance should not be affected, and this can be very useful
for debugging and adding new trace events to paths in the future.

Note eBPF programs can attach to these events, as well as perf
can count them since we're attaching to the events subsystem
in the kernel.

Co-developed-by: Ben Shelton <benjamin.h.shelton@intel.com>
Signed-off-by: Ben Shelton <benjamin.h.shelton@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

show more ...

intel: Remove rcu_read_lock() around XDP program invocation

The Intel drivers all have rcu_read_lock()/rcu_read_unlock() pairs around
XDP program invocations. However, the actual lifetime of the obj

intel: Remove rcu_read_lock() around XDP program invocation

The Intel drivers all have rcu_read_lock()/rcu_read_unlock() pairs around
XDP program invocations. However, the actual lifetime of the objects
referred by the XDP program invocation is longer, all the way through to
the call to xdp_do_flush(), making the scope of the rcu_read_lock() too
small. This turns out to be harmless because it all happens in a single
NAPI poll cycle (and thus under local_bh_disable()), but it makes the
rcu_read_lock() misleading.

Rather than extend the scope of the rcu_read_lock(), just get rid of it
entirely. With the addition of RCU annotations to the XDP_REDIRECT map
types that take bh execution into account, lockdep even understands this to
be safe, so there's really no reason to keep it around.

Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com> # i40e
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Link: https://lore.kernel.org/bpf/20210624160609.292325-12-toke@redhat.com

show more ...

ice: report hash type such as L2/L3/L4

The hardware is reporting the type of the hash used for RSS
as a PTYPE field in the receive descriptor. Use this value to set
the skb packet hash type by exten

ice: report hash type such as L2/L3/L4

The hardware is reporting the type of the hash used for RSS
as a PTYPE field in the receive descriptor. Use this value to set
the skb packet hash type by extending the hash type table to
cover all 10-bits of possible values (requiring some variables
to be changed from u8 to u16), and then use that table to convert
to one of the possible values in enum pkt_hash_types.

While we're here, remove the unused ptype struct value, which
makes table init easier for the zero entries, and use ranged
initializer to remove a bunch of code (works with gcc and clang).

Without this change, the kernel will recalculate the hash in software,
which can consume extra CPU cycles.

Co-developed-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

show more ...

ice: enable transmit timestamps for E810 devices

Add support for enabling Tx timestamp requests for outgoing packets on
E810 devices.

The ice hardware can support multiple outstanding Tx timestamp

ice: enable transmit timestamps for E810 devices

Add support for enabling Tx timestamp requests for outgoing packets on
E810 devices.

The ice hardware can support multiple outstanding Tx timestamp requests.
When sending a descriptor to hardware, a Tx timestamp request is made by
setting a request bit, and assigning an index that represents which Tx
timestamp index to store the timestamp in.

Hardware makes no effort to synchronize the index use, so it is up to
software to ensure that Tx timestamp indexes are not re-used before the
timestamp is reported back.

To do this, introduce a Tx timestamp tracker which will keep track of
currently in-use indexes.

In the hot path, if a packet has a timestamp request, an index will be
requested from the tracker. Unfortunately, this does require a lock as
the indexes are shared across all queues on a PHY. There are not enough
indexes to reliably assign only 1 to each queue.

For the E810 devices, the timestamp indexes are not shared across PHYs,
so each port can have its own tracking.

Once hardware captures a timestamp, an interrupt is fired. In this
interrupt, trigger a new work item that will figure out which timestamp
was completed, and report the timestamp back to the stack.

This function loops through the Tx timestamp indexes and checks whether
there is now a valid timestamp. If so, it clears the PHY timestamp
indication in the PHY memory, locks and removes the SKB and bit in the
tracker, then reports the timestamp to the stack.

It is possible in some cases that a timestamp request will be initiated
but never completed. This might occur if the packet is dropped by
software or hardware before it reaches the PHY.

Add a task to the periodic work function that will check whether
a timestamp request is more than a few seconds old. If so, the timestamp
index is cleared in the PHY, and the SKB is released.

Just as with Rx timestamps, the Tx timestamps are only 40 bits wide, and
use the same overall logic for extending to 64 bits of nanoseconds.

With this change, E810 devices should be able to perform basic PTP
functionality.

Future changes will extend the support to cover the E822-based devices.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

show more ...

ice: Allow all LLDP packets from PF to Tx

Currently in the ice driver, the check whether to
allow a LLDP packet to egress the interface from the
PF_VSI is being based on the SKB's priority field.
It

ice: Allow all LLDP packets from PF to Tx

Currently in the ice driver, the check whether to
allow a LLDP packet to egress the interface from the
PF_VSI is being based on the SKB's priority field.
It checks to see if the packets priority is equal to
TC_PRIO_CONTROL. Injected LLDP packets do not always
meet this condition.

SCAPY defaults to a sk_buff->protocol value of ETH_P_ALL
(0x0003) and does not set the priority field. There will
be other injection methods (even ones used by end users)
that will not correctly configure the socket so that
SKB fields are correctly populated.

Then ethernet header has to have to correct value for
the protocol though.

Add a check to also allow packets whose ethhdr->h_proto
matches ETH_P_LLDP (0x88CC).

Fixes: 0c3a6101ff2d ("ice: Allow egress control packets from PF_VSI")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

show more ...

ice: add correct exception tracing for XDP

Add missing exception tracing to XDP when a number of different
errors can occur. The support was only partial. Several errors
where not logged which would

ice: add correct exception tracing for XDP

Add missing exception tracing to XDP when a number of different
errors can occur. The support was only partial. Several errors
where not logged which would confuse the user quite a lot not
knowing where and why the packets disappeared.

Fixes: efc2214b6047 ("ice: Add support for XDP")
Fixes: 2d4238f55697 ("ice: Add support for AF_XDP")
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

show more ...

ice: refactor ITR data structures

Use a dedicated bitfield in order to both increase
the amount of checking around the length of ITR writes
as well as simplify the checks of dynamic mode.

Basically

ice: refactor ITR data structures

Use a dedicated bitfield in order to both increase
the amount of checking around the length of ITR writes
as well as simplify the checks of dynamic mode.

Basically unpack the "high bit means dynamic" logic
into bitfields.

Also, remove some unused ITR defines.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

show more ...

ice: manage interrupts during poll exit

The driver would occasionally miss that there were outstanding
descriptors to clean when exiting busy/napi poll. This issue has
been in the code since the int

ice: manage interrupts during poll exit

The driver would occasionally miss that there were outstanding
descriptors to clean when exiting busy/napi poll. This issue has
been in the code since the introduction of the ice driver.

Attempt to "catch" any remaining work by triggering a software
interrupt when exiting napi poll or busy-poll. This will not
cause extra interrupts in the case of normal execution.

This issue was found when running sfnt-pingpong, with busy
poll enabled, and typically with larger I/O sizes like > 8192,
the program would occasionally report > 1 second maximums
to complete a ping pong.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

show more ...

ice: replace custom AIM algorithm with kernel's DIM library

The ice driver has support for adaptive interrupt moderation, an
algorithm for tuning the interrupt rate dynamically. This algorithm
is ba

ice: replace custom AIM algorithm with kernel's DIM library

The ice driver has support for adaptive interrupt moderation, an
algorithm for tuning the interrupt rate dynamically. This algorithm
is based on various assumptions about ring size, socket buffer size,
link speed, SKB overhead, ethernet frame overhead and more.

The Linux kernel has support for a dynamic interrupt moderation
algorithm known as "dimlib". Replace the custom driver-specific
implementation of dynamic interrupt moderation with the kernel's
algorithm.

The Intel hardware has a different hardware implementation than the
originators of the dimlib code had to work with, which requires the
driver to use a slightly different set of inputs for the actual
moderation values, while getting all the advice from dimlib of
better/worse, shift left or right.

The change made for this implementation is to use a pair of values
for each of the 5 "slots" that the dimlib moderation expects, and
the driver will program those pairs when dimlib recommends a slot to
use. The currently implementation uses two tables, one for receive
and one for transmit, and the pairs of values in each slot set the
maximum delay of an interrupt and a maximum number of interrupts per
second (both expressed in microseconds).

There are two separate kinds of bugs fixed by using DIMLIB, one is
UDP single stream send was too slow, and the other is that 8K
ping-pong was going to the most aggressive moderation and has much
too high latency.

The overall result of using DIMLIB is that we meet or exceed our
performance expectations set based on the old algorithm.

Co-developed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

show more ...

ice: Consolidate VSI state and flags

struct ice_vsi has two fields, state and flags which seem to
be serving the same purpose. Consolidate them into one field
'state'.

enum ice_state is used to rep

ice: Consolidate VSI state and flags

struct ice_vsi has two fields, state and flags which seem to
be serving the same purpose. Consolidate them into one field
'state'.

enum ice_state is used to represent state information of the PF.
While some of these enum values can be use to represent VSI state,
it makes more sense to represent VSI state with its own enum. So
derive a new enum ice_vsi_state from ice_vsi_flags and ice_state
and use it. Also rename enum ice_state to ice_pf_state for clarity.

Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

show more ...

ice: Check FDIR program status for AVF

Enable returning FDIR completion status by checking the
ctrl_vsi Rx queue descriptor value.

To enable returning FDIR completion status from ctrl_vsi Rx queue,

ice: Check FDIR program status for AVF

Enable returning FDIR completion status by checking the
ctrl_vsi Rx queue descriptor value.

To enable returning FDIR completion status from ctrl_vsi Rx queue,
COMP_Queue and COMP_Report of FDIR filter programming descriptor
needs to be properly configured. After program request sent to ctrl_vsi
Tx queue, ctrl_vsi Rx queue interrupt will be triggered and
completion status will be returned.

Driver will first issue request in ice_vc_fdir_add_fltr(), then
pass FDIR context to the background task in interrupt service routine
ice_vc_fdir_irq_handler() and finally deal with them in
ice_flush_fdir_ctx(). ice_flush_fdir_ctx() will check the descriptor's
value, fdir context, and then send back virtual channel message to VF
by calling ice_vc_add_fdir_fltr_post(). An additional timer will be
setup in case of hardware interrupt timeout.

Signed-off-by: Yahui Cao <yahui.cao@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

show more ...

bpf, devmap: Move drop error path to devmap for XDP_REDIRECT

We want to change the current ndo_xdp_xmit drop semantics because it will
allow us to implement better queue overflow handling. This is w

bpf, devmap: Move drop error path to devmap for XDP_REDIRECT

We want to change the current ndo_xdp_xmit drop semantics because it will
allow us to implement better queue overflow handling. This is working
towards the larger goal of a XDP TX queue-hook. Move XDP_REDIRECT error
path handling from each XDP ethernet driver to devmap code. According to
the new APIs, the driver running the ndo_xdp_xmit pointer, will break tx
loop whenever the hw reports a tx error and it will just return to devmap
caller the number of successfully transmitted frames. It will be devmap
responsibility to free dropped frames.

Move each XDP ndo_xdp_xmit capable driver to the new APIs:

- veth
- virtio-net
- mvneta
- mvpp2
- socionext
- amazon ena
- bnxt
- freescale (dpaa2, dpaa)
- xen-frontend
- qede
- ice
- igb
- ixgbe
- i40e
- mlx5
- ti (cpsw, cpsw-new)
- tun
- sfc

Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Camelia Groza <camelia.groza@nxp.com>
Acked-by: Edward Cree <ecree.xilinx@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Shay Agroskin <shayagr@amazon.com>
Link: https://lore.kernel.org/bpf/ed670de24f951cfd77590decf0229a0ad7fd12f6.1615201152.git.lorenzo@kernel.org

show more ...

ice: move headroom initialization to ice_setup_rx_ctx

ice_rx_offset(), that is supposed to initialize the Rx buffer headroom,
relies on ICE_RX_FLAGS_RING_BUILD_SKB flag as well as XDP prog presence.

ice: move headroom initialization to ice_setup_rx_ctx

ice_rx_offset(), that is supposed to initialize the Rx buffer headroom,
relies on ICE_RX_FLAGS_RING_BUILD_SKB flag as well as XDP prog presence.

Currently, the callsite of mentioned function is placed incorrectly
within ice_setup_rx_ring() where Rx ring's build skb flag is not
set yet. This causes the XDP_REDIRECT to be partially broken due to
inability to create xdp_frame in the headroom space, as the headroom is
0.

Fix this by moving ice_rx_offset() to ice_setup_rx_ctx() after the flag
setting.

Fixes: f1b1f409bf79 ("ice: store the result of ice_rx_offset() onto ice_ring")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

show more ...

ice: store the result of ice_rx_offset() onto ice_ring

Output of ice_rx_offset() is based on ethtool's priv flag setting, which
when changed, causes PF reset (disables napi, frees irqs, loads
differ

ice: store the result of ice_rx_offset() onto ice_ring

Output of ice_rx_offset() is based on ethtool's priv flag setting, which
when changed, causes PF reset (disables napi, frees irqs, loads
different Rx mem model, etc.). This means that within napi its result is
constant and there is no reason to call it per each processed frame.

Add new 'rx_offset' field to ice_ring that is meant to hold the
ice_rx_offset() result and use it within ice_clean_rx_irq().
Furthermore, use it within ice_alloc_mapped_page().

Reviewed-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

show more ...

ice: move skb pointer from rx_buf to rx_ring

Similar thing has been done in i40e, as there is no real need for having
the sk_buff pointer in each rx_buf. Non-eop frames can be simply handled
on that

ice: move skb pointer from rx_buf to rx_ring

Similar thing has been done in i40e, as there is no real need for having
the sk_buff pointer in each rx_buf. Non-eop frames can be simply handled
on that pointer moved upwards to rx_ring.

Reviewed-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

show more ...

ice: simplify ice_run_xdp

There's no need for 'result' variable, we can directly return the
internal status based on action returned by xdp prog.

Reviewed-by: Björn Töpel <bjorn.topel@intel.com>
Si

ice: simplify ice_run_xdp

There's no need for 'result' variable, we can directly return the
internal status based on action returned by xdp prog.

Reviewed-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

show more ...

ice: Refactor DCB related variables out of the ice_port_info struct

Refactor the DCB related variables out of the ice_port_info_struct. The
goal is to make the ice_port_info struct cleaner.

Signed-

ice: Refactor DCB related variables out of the ice_port_info struct

Refactor the DCB related variables out of the ice_port_info_struct. The
goal is to make the ice_port_info struct cleaner.

Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Co-developed-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

show more ...

ice: fix writeback enable logic

The writeback enable logic was incorrectly implemented (due to
misunderstanding what the side effects of the implementation would be
during polling).

Fix this logic

ice: fix writeback enable logic

The writeback enable logic was incorrectly implemented (due to
misunderstanding what the side effects of the implementation would be
during polling).

Fix this logic issue, while implementing a new feature allowing the user
to control the writeback frequency using the knobs for controlling
interrupt throttling that we already have. Basically if you leave
adaptive interrupts enabled, the writeback frequency will be varied even
if busy_polling or if napi-poll is in use. If the interrupt rates are
set to a fixed value by ethtool -C and adaptive is off, the driver will
allow the user-set interrupt rate to guide how frequently the hardware
will complete descriptors to the driver.

Effectively the user will get a control over the hardware efficiency,
allowing the choice between immediate interrupts or delayed up to a
maximum of the interrupt rate, even when interrupts are disabled
during polling.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Co-developed-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

show more ...

net: use the new dev_page_is_reusable() instead of private versions

Now we can remove a bunch of identical functions from the drivers and
make them use common dev_page_is_reusable(). All {,un}likely

net: use the new dev_page_is_reusable() instead of private versions

Now we can remove a bunch of identical functions from the drivers and
make them use common dev_page_is_reusable(). All {,un}likely() checks
are omitted since it's already present in this helper.
Also update some comments near the call sites.

Suggested-by: David Rientjes <rientjes@google.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Cc: John Hubbard <jhubbard@nvidia.com>
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

ice: Implement flow for IPv6 next header (extension header)

This patch is based on a similar change to i40e by Slawomir Laba:
"i40e: Implement flow for IPv6 next header (extension header)".

When a

ice: Implement flow for IPv6 next header (extension header)

This patch is based on a similar change to i40e by Slawomir Laba:
"i40e: Implement flow for IPv6 next header (extension header)".

When a packet contains an IPv6 header with next header which is
an extension header and not a protocol one, the kernel function
skb_transport_header called with such sk_buff will return a
pointer to the extension header and not to the TCP one.

The above explained call caused a problem with packet processing
for skb with encapsulation for tunnel with ICE_TX_CTX_EIPT_IPV6.
The extension header was not skipped at all.

The ipv6_skip_exthdr function does check if next header of the IPV6
header is an extension header and doesn't modify the l4_proto pointer
if it points to a protocol header value so its safe to omit the
comparison of exthdr and l4.hdr pointers. The ipv6_skip_exthdr can
return value -1. This means that the skipping process failed
and there is something wrong with the packet so it will be dropped.

Fixes: a4e82a81f573 ("ice: Add support for tunnel offloads")
Signed-off-by: Nick Nunley <nicholas.d.nunley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

show more ...

net, xdp: Introduce xdp_prepare_buff utility routine

Introduce xdp_prepare_buff utility routine to initialize per-descriptor
xdp_buff fields (e.g. xdp_buff pointers). Rely on xdp_prepare_buff() in
a

net, xdp: Introduce xdp_prepare_buff utility routine

Introduce xdp_prepare_buff utility routine to initialize per-descriptor
xdp_buff fields (e.g. xdp_buff pointers). Rely on xdp_prepare_buff() in
all XDP capable drivers.

Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Shay Agroskin <shayagr@amazon.com>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Link: https://lore.kernel.org/bpf/45f46f12295972a97da8ca01990b3e71501e9d89.1608670965.git.lorenzo@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

show more ...

net, xdp: Introduce xdp_init_buff utility routine

Introduce xdp_init_buff utility routine to initialize xdp_buff fields
const over NAPI iterations (e.g. frame_sz or rxq pointer). Rely on
xdp_init_bu

net, xdp: Introduce xdp_init_buff utility routine

Introduce xdp_init_buff utility routine to initialize xdp_buff fields
const over NAPI iterations (e.g. frame_sz or rxq pointer). Rely on
xdp_init_buff in all XDP capable drivers.

Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Shay Agroskin <shayagr@amazon.com>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Link: https://lore.kernel.org/bpf/7f8329b6da1434dc2b05a77f2e800b29628a8913.1608670965.git.lorenzo@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

show more ...