enic: Add support for adaptive interrupt coalescing

This patch adds support for adaptive interrupt coalescing.

For small pkts with low pkt rate, we can decrease the coalescing inter

enic: Add support for adaptive interrupt coalescing

This patch adds support for adaptive interrupt coalescing.

For small pkts with low pkt rate, we can decrease the coalescing interrupt
dynamically which decreases the latency. This however increases the cpu
utilization. Based on testing with different coal intr and pkt rate we came up
with a table(mod_table) with rx_rate and coalescing interrupt value where we
get low latency without significant increase in cpu. mod_table table stores
the coalescing timer percentage value for different throughputs.

Function enic_calc_int_moderation() calculates the desired coalescing intr timer
value. This function is called in driver rx napi_poll. The actual value is set
by enic_set_int_moderation() which is called when napi_poll is complete. i.e
when we unmask the rx intr.

Adaptive coal intr is support only when driver is using msix intr. Because
intr is not shared.

Struct mod_range is used to store only the default adaptive coalescing intr
value.

Adaptive coal intr calue is calculated by

timer = range_start + ((rx_coal->range_end - range_start) *
mod_table[index].range_percent / 100);

rx_coal->range_end is the rx-usecs-high value set using ethtool.
range_start is rx-usecs-low, set using ethtool, if rx_small_pkt_bytes_cnt is
greater than 2 * rx_large_pkt_bytes_cnt. i.e small pkts are dominant. Else its
rx-usecs-low + 3.

Cc: Christian Benvenuti <benve@cisco.com>
Cc: Neel Patel <neepatel@cisco.com>
Signed-off-by: Sujith Sankar <ssujith@cisco.com>
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

enic: Call dev_kfree_skb_any instead of dev_kfree_skb.

Replace dev_kfree_skb with dev_kfree_skb_any in enic_hard_start_xmit
that can be called in hard irq and other contexts.

en

enic: Call dev_kfree_skb_any instead of dev_kfree_skb.

Replace dev_kfree_skb with dev_kfree_skb_any in enic_hard_start_xmit
that can be called in hard irq and other contexts.

enic_hard_start_xmit only frees the skb when dropping it.

Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>

show more ...

enic: Don't receive packets when the napi budget == 0

Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.

This matters as netpoll will s

enic: Don't receive packets when the napi budget == 0

Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.

This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.

Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

enic: Use pci_enable_msix_range() instead of pci_enable_msix()

As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
usi

enic: Use pci_enable_msix_range() instead of pci_enable_msix()

As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.

Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Christian Benvenuti <benve@cisco.com>
Cc: Sujith Sankar <ssujith@cisco.com>
Cc: Govindarajulu Varadarajan <govindarajulu90@gmail.com>
Cc: Neel Patel <neepatel@cisco.com>
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Acked-by: Govindarajulu Varadarajan <govindarajulu90@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: cisco-enic calls skb_set_hash

Drivers should call skb_set_hash to set the hash and its type
in an skbuff.

Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by

net: cisco-enic calls skb_set_hash

Drivers should call skb_set_hash to set the hash and its type
in an skbuff.

Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: enic: remove unnecessary pci_set_drvdata()

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the

net: enic: remove unnecessary pci_set_drvdata()

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

driver/net: enic: Try DMA 64 first, then failover to DMA

In servers with more than 1.1 TB of RAM, the existing 40/32 bit DMA
could cause failure as the DMA-able address could go outside

driver/net: enic: Try DMA 64 first, then failover to DMA

In servers with more than 1.1 TB of RAM, the existing 40/32 bit DMA
could cause failure as the DMA-able address could go outside the range
addressable using 40/32 bits.

The following patch first tried 64 bit DMA if possible, failover to 32
bit.

Signed-off-by: Sujith Sankar <ssujith@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: Govindarajulu Varadarajan <govindarajulu90@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

driver/net: enic: record q_number and rss_hash for skb

The following patch sets the skb->rxhash and skb->q_number.
This is used by RPS and RFS. Kernel can make use of hw provided hash

driver/net: enic: record q_number and rss_hash for skb

The following patch sets the skb->rxhash and skb->q_number.
This is used by RPS and RFS. Kernel can make use of hw provided hash
instead of calculating the hash.

Signed-off-by: Govindarajulu Varadarajan <govindarajulu90@gmail.com>
Signed-off-by: Nishank Trivedi <nistrive@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

driver/net: enic: Add multi tx support for enic

The following patch adds multi tx support for enic.

Signed-off-by: Nishank Trivedi <nistrive@cisco.com>
Signed-off-by: Christian

driver/net: enic: Add multi tx support for enic

The following patch adds multi tx support for enic.

Signed-off-by: Nishank Trivedi <nistrive@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: Govindarajulu Varadarajan <govindarajulu90@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

drivers/net: enic: Generate notification of hardware crash

This patch generates a hardware crash notification (NETDEV_REBOOT)
during reset. After a hardware crash, ENIC resets all its re

drivers/net: enic: Generate notification of hardware crash

This patch generates a hardware crash notification (NETDEV_REBOOT)
during reset. After a hardware crash, ENIC resets all its resources
including queue pair filters programmed by USNIC. USNIC registers for
this notification, and on receiving it, reprograms the queue pair
filters.

Signed-off-by: Neel Patel <neepatel@cisco.com>
Signed-off-by: Nishank Trivedi <nistrive@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

drivers/net: enic: Add an interface for USNIC to interact with firmware

This patch adds an interface for USNIC to proxy firmware commands
through ENIC.

Signed-off-by: Neel Patel

drivers/net: enic: Add an interface for USNIC to interact with firmware

This patch adds an interface for USNIC to proxy firmware commands
through ENIC.

Signed-off-by: Neel Patel <neepatel@cisco.com>
Signed-off-by: Nishank Trivedi <nistrive@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

drivers/net: enic: Move ethtool code to a separate file

This patch moves all enic ethtool hooks from enic_main.c to a new file
enic_ethtool.c

Signed-off-by: Neel Patel <neepatel

drivers/net: enic: Move ethtool code to a separate file

This patch moves all enic ethtool hooks from enic_main.c to a new file
enic_ethtool.c

Signed-off-by: Neel Patel <neepatel@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: Nishank Trivedi <nistrive@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

drivers/net: enic: release rtnl_lock on error-path

enic_change_mtu_work() must call rtnl_unlock() on all exiting paths.

Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>

drivers/net: enic: release rtnl_lock on error-path

enic_change_mtu_work() must call rtnl_unlock() on all exiting paths.

Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Christian Benvenuti <benve@cisco.com>
Cc: Roopa Prabhu <roprabhu@cisco.com>
Cc: Neel Patel <neepatel@cisco.com>
Cc: Nishank Trivedi <nistrive@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: vlan: add protocol argument to packet tagging functions

Add a protocol argument to the VLAN packet tagging functions. In case of HW
tagging, we need that protocol available in the n

net: vlan: add protocol argument to packet tagging functions

Add a protocol argument to the VLAN packet tagging functions. In case of HW
tagging, we need that protocol available in the ndo_start_xmit functions,
so it is stored in a new field in the skb. The new field fits into a hole
(on 64 bit) and doesn't increase the sks's size.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: vlan: rename NETIF_F_HW_VLAN_* feature flags to NETIF_F_HW_VLAN_CTAG_*

Rename the hardware VLAN acceleration features to include "CTAG" to indicate
that they only support CTAGs. Fol

net: vlan: rename NETIF_F_HW_VLAN_* feature flags to NETIF_F_HW_VLAN_CTAG_*

Rename the hardware VLAN acceleration features to include "CTAG" to indicate
that they only support CTAGs. Follow up patches will introduce 802.1ad
server provider tagging (STAGs) and require the distinction for hardware not
supporting acclerating both.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

enic: change sprintf() to snprintf()

These are copying data into 16 char arrays. They all specify that the
first string can't be more than 11 characters but once you add on the
"-rx

enic: change sprintf() to snprintf()

These are copying data into 16 char arrays. They all specify that the
first string can't be more than 11 characters but once you add on the
"-rx-" and the NUL character there isn't space for the %d.

The first string is probably never going to be 11 characters, but if it
is then let's truncate the string instead of corrupting memory.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: remove unnecessary NET_ADDR_RANDOM "bitclean"

NET_ADDR_SET is set in dev_set_mac_address() no need to alter
dev->addr_assign_type value in drivers.

Signed-off-by: Jiri Pirk

net: remove unnecessary NET_ADDR_RANDOM "bitclean"

NET_ADDR_SET is set in dev_set_mac_address() no need to alter
dev->addr_assign_type value in drivers.

Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

drivers/net: fix up function prototypes after __dev* removals

The __dev* removal patches for the network drivers ended up messing up
the function prototypes for a bunch of drivers. This

drivers/net: fix up function prototypes after __dev* removals

The __dev* removal patches for the network drivers ended up messing up
the function prototypes for a bunch of drivers. This patch fixes all of
them back up to be properly aligned.

Bonus is that this almost removes 100 lines of code, always a nice
surprise.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

enic: remove __dev* attributes

CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata,

enic: remove __dev* attributes

CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.

Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Christian Benvenuti <benve@cisco.com>
Cc: Roopa Prabhu <roprabhu@cisco.com>
Cc: Neel Patel <neepatel@cisco.com>
Cc: Nishank Trivedi <nistrive@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

enic: remove unnecessary setting of skb->dev

skb->dev is being unnecessarily set after calling eth_type_trans.
eth_type_trans already sets skb->dev to the proper value, thus making this

enic: remove unnecessary setting of skb->dev

skb->dev is being unnecessarily set after calling eth_type_trans.
eth_type_trans already sets skb->dev to the proper value, thus making this
unnecessary.

Signed-off-by: Jon Mason <jdmason@kudzu.us>
Cc: Christian Benvenuti <benve@cisco.com>
Cc: Roopa Prabhu <roprabhu@cisco.com>
Cc: Neel Patel <neepatel@cisco.com>
Cc: Nishank Trivedi <nistrive@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

drivers/net: Convert compare_ether_addr to ether_addr_equal

Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr

drivers/net: Convert compare_ether_addr to ether_addr_equal

Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.

Done via cocci script:

$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)

@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)

@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)

@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)

@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)

@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)

@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

enic: Stop using NLA_PUT*().

These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.

Signed-off-by: David S. Miller <davem@davemloft.

enic: Stop using NLA_PUT*().

These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.

Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

enic: Fix addr valid check in enic_set_vf_mac

zero mac address is a valid address for VIC dynamic vnic and sriov Vf's.
Fix the check in enic_set_vf_mac appropriately

Signed-off-

enic: Fix addr valid check in enic_set_vf_mac

zero mac address is a valid address for VIC dynamic vnic and sriov Vf's.
Fix the check in enic_set_vf_mac appropriately

Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: Sujith Sankar <ssujith@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net

Conflicts:
drivers/net/ethernet/broadcom/tg3.c

Conflicts in the statistics regression bug fix from 'net',

Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net

Conflicts:
drivers/net/ethernet/broadcom/tg3.c

Conflicts in the statistics regression bug fix from 'net',
but happily Matt Carlson originally posted the fix against
'net-next' so I used that to resolve this.

Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

enic: fix an endian bug in enic_probe()

"num_vfs" is a u32 but we only use the high 16 bits and the low 16bits
are left as zero. That isn't a problem for little endian systems but it

enic: fix an endian bug in enic_probe()

"num_vfs" is a u32 but we only use the high 16 bits and the low 16bits
are left as zero. That isn't a problem for little endian systems but it
will break on big endian ones.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...