cpufreq: Add Tegra186 cpufreq driver

Add a new cpufreq driver for Tegra186 (and likely later).
The CPUs are organized into two clusters, Denver and A57,
with two and four cores respectively. CPU fre

cpufreq: Add Tegra186 cpufreq driver

Add a new cpufreq driver for Tegra186 (and likely later).
The CPUs are organized into two clusters, Denver and A57,
with two and four cores respectively. CPU frequency can be
adjusted by writing the desired rate divisor and a voltage
hint to a special per-core register.

The frequency of each core can be set individually; however,
this is just a hint as all CPUs in a cluster will run at
the maximum rate of non-idle CPUs in the cluster.

Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

cpufreq: CPPC: add ACPI_PROCESSOR dependency

Without the Kconfig dependency, we can get this warning:

warning: ACPI_CPPC_CPUFREQ selects ACPI_CPPC_LIB which has unmet direct dependencies (ACPI && A

cpufreq: CPPC: add ACPI_PROCESSOR dependency

Without the Kconfig dependency, we can get this warning:

warning: ACPI_CPPC_CPUFREQ selects ACPI_CPPC_LIB which has unmet direct dependencies (ACPI && ACPI_PROCESSOR)

Fixes: 5477fb3bd1e8 (ACPI / CPPC: Add a CPUFreq driver for use with CPPC)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

cpufreq: ti: Add cpufreq driver to determine available OPPs at runtime

Some TI SoCs, like those in the AM335x, AM437x, DRA7x, and AM57x families,
have different OPPs available for the MPU depending

cpufreq: ti: Add cpufreq driver to determine available OPPs at runtime

Some TI SoCs, like those in the AM335x, AM437x, DRA7x, and AM57x families,
have different OPPs available for the MPU depending on which specific
variant of the SoC is in use. This can be determined through use of the
revision and an eFuse register present in the silicon. Introduce a
ti-cpufreq driver that can read the aformentioned values and provide
them as version matching data to the opp framework. Through this the
opp-supported-hw dt binding that is part of the operating-points-v2
table can be used to indicate availability of OPPs for each device.

This driver also creates the "cpufreq-dt" platform_device after passing
the version matching data to the OPP framework so that the cpufreq-dt
handles the actual cpufreq implementation. Even without the necessary
data to pass the version matching data the driver will still create this
device to maintain backwards compatibility with operating-points v1
tables.

Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

cpufreq: brcmstb-avs-cpufreq: add debugfs support

In order to aid debugging, we add a debugfs interface to the driver
that allows direct interaction with the AVS co-processor.

The debugfs interface

cpufreq: brcmstb-avs-cpufreq: add debugfs support

In order to aid debugging, we add a debugfs interface to the driver
that allows direct interaction with the AVS co-processor.

The debugfs interface provides a means for reading all and writing some
of the mailbox registers directly from the shell prompt and enables a
user to execute the communications protocol between ARM CPU and AVS CPU
step-by-step.

This interface should be used for debugging purposes only.

Signed-off-by: Markus Mayer <mmayer@broadcom.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

cpufreq: brcmstb-avs-cpufreq: AVS CPUfreq driver for Broadcom STB SoCs

This driver supports voltage and frequency scaling on Broadcom STB SoCs
using AVS firmware with DFS and DVFS support.

Actual f

cpufreq: brcmstb-avs-cpufreq: AVS CPUfreq driver for Broadcom STB SoCs

This driver supports voltage and frequency scaling on Broadcom STB SoCs
using AVS firmware with DFS and DVFS support.

Actual frequency or voltage scaling is done exclusively by the AVS
firmware. The driver merely provides a standard CPUfreq interface to
other kernel components and userland, and instructs the AVS firmware to
perform frequency or voltage changes on its behalf.

Signed-off-by: Markus Mayer <mmayer@broadcom.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

cpufreq: retire the Integrator cpufreq driver

After switching the core module clocks controlling the Integrator
clock frequencies to the common clock framework, defining the
operating points in the

cpufreq: retire the Integrator cpufreq driver

After switching the core module clocks controlling the Integrator
clock frequencies to the common clock framework, defining the
operating points in the device tree, and activating the generic
DT-based CPUfreq driver, we can retire the old Integrator
cpufreq driver.

Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

cpufreq: hisilicon: Use generic platdev driver

The cpufreq-dt-platdev driver supports creation of cpufreq-dt platform
device now, reuse that and remove similar code from platform code.

Signed-off-b

cpufreq: hisilicon: Use generic platdev driver

The cpufreq-dt-platdev driver supports creation of cpufreq-dt platform
device now, reuse that and remove similar code from platform code.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

cpufreq: mediatek: allow building as a module

The MT8173 cpufreq driver can currently only be built-in, but
it has a Kconfig dependency on the thermal core. THERMAL
can be a loadable module, which i

cpufreq: mediatek: allow building as a module

The MT8173 cpufreq driver can currently only be built-in, but
it has a Kconfig dependency on the thermal core. THERMAL
can be a loadable module, which in turn makes this driver
impossible to build.

It is nicer to make the cpufreq driver a module as well, so
this patch turns the option in to a 'tristate' and adapts
the dependency accordingly.

The driver has no module_exit() function, so it will continue
to not support unloading, but it can be built as a module
and loaded at runtime now.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 5269e7067cd6 (cpufreq: Add ARM_MT8173_CPUFREQ dependency on THERMAL)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

cpufreq: st: Provide runtime initialised driver for ST's platforms

The bootloader is charged with the responsibility to provide platform
specific Dynamic Voltage and Frequency Scaling (DVFS) informa

cpufreq: st: Provide runtime initialised driver for ST's platforms

The bootloader is charged with the responsibility to provide platform
specific Dynamic Voltage and Frequency Scaling (DVFS) information via
Device Tree. This driver takes the supplied configuration and
registers it with the new generic OPP framework, to then be used with
CPUFreq.

Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

cpufreq: tegra: add regulator dependency for T124

This driver is the only one that calls regulator_sync_voltage(), but it
can currently be built with CONFIG_REGULATOR disabled, producing
this build

cpufreq: tegra: add regulator dependency for T124

This driver is the only one that calls regulator_sync_voltage(), but it
can currently be built with CONFIG_REGULATOR disabled, producing
this build error:

drivers/cpufreq/tegra124-cpufreq.c: In function 'tegra124_cpu_switch_to_pllx':
drivers/cpufreq/tegra124-cpufreq.c:68:2: error: implicit declaration of function 'regulator_sync_voltage' [-Werror=implicit-function-declaration]
regulator_sync_voltage(priv->vdd_cpu_reg);

My first attempt was to implement a helper for this function
for regulator_sync_voltage, but Mark Brown explained:

We don't do this for *all* regulator API functions - there's some where
using them strongly suggests that there is actually a dependency on
the regulator API. This does seem like it might be falling into the
specialist category [...]
Looking at the code I'm pretty unclear on what the authors think the
use of _sync_voltage() is doing in the first place so it may be even
better to just remove the call. It seems to have been included in the
first commit so there's not changelog explaining things and there's
no comment either. I'd *expect* it to be a noop as far as I can see.

This adds the dependency to make the driver always build successfully
or not be enabled at all. Alternatively, we could investigate if the
driver should stop calling regulator_sync_voltage instead.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

cpufreq: arm_big_little: Add support to register a cpufreq cooling device

Register passive cooling devices when initialising cpufreq on
big.LITTLE systems. If the device tree provides a dynamic powe

cpufreq: arm_big_little: Add support to register a cpufreq cooling device

Register passive cooling devices when initialising cpufreq on
big.LITTLE systems. If the device tree provides a dynamic power
coefficient for the CPUs then the bound cooling device will support
the extensions that allow it to be used with all the existing thermal
governors including the power allocator governor.

A cooling device will be created per individual frequency domain and
can be bound to thermal zones via the thermal DT bindings.

Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

cpufreq: SCPI: Depend on SCPI clk driver

The SCPI clk driver registers the virtual cpufreq device that kicks off
initialisation of the SCPI cpufreq driver. Also, clk_get() will fail for
the cpufreq

cpufreq: SCPI: Depend on SCPI clk driver

The SCPI clk driver registers the virtual cpufreq device that kicks off
initialisation of the SCPI cpufreq driver. Also, clk_get() will fail for
the cpufreq driver if the SCPI clk driver is missing.

Fix this by making the SCPI cpufreq driver explicitly depend on the SCPI
clk driver.

Fixes: 8def31034d03 (cpufreq: arm_big_little: add SCPI interface driver)
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

cpufreq: mediatek: fix build error

The recently added mt8173 cpufreq driver relies on the cpu topology
that is always present on ARM64 but optional on ARM32:

drivers/cpufreq/mt8173-cpufreq.c: In fu

cpufreq: mediatek: fix build error

The recently added mt8173 cpufreq driver relies on the cpu topology
that is always present on ARM64 but optional on ARM32:

drivers/cpufreq/mt8173-cpufreq.c: In function 'mtk_cpufreq_init':
drivers/cpufreq/mt8173-cpufreq.c:441:30: error: 'cpu_topology' undeclared (first use in this function)
cpumask_copy(policy->cpus, &cpu_topology[policy->cpu].core_sibling);

This refines the Kconfig dependencies so that we can still build on
ARM32, but only if COMPILE_TEST is selected and the CPU topology
code is present.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

ACPI / CPPC: Add a CPUFreq driver for use with CPPC

This driver utilizes the methods introduced in a previous
patch titled - "ACPI: Introduce CPU performance controls using CPPC"
and enables usage w

ACPI / CPPC: Add a CPUFreq driver for use with CPPC

This driver utilizes the methods introduced in a previous
patch titled - "ACPI: Introduce CPU performance controls using CPPC"
and enables usage with existing CPUFreq governors.

Signed-off-by: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Reviewed-by: Al Stone <al.stone@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

cpufreq: arm_big_little: add SCPI interface driver

On some ARM based systems, a separate Cortex-M based System Control
Processor(SCP) provides the overall power, clock, reset and system
control incl

cpufreq: arm_big_little: add SCPI interface driver

On some ARM based systems, a separate Cortex-M based System Control
Processor(SCP) provides the overall power, clock, reset and system
control including CPU DVFS. SCPI Message Protocol is used to
communicate with the SCPI.

This patch adds a interface driver for adding OPPs and registering
the arm_big_little cpufreq driver for such systems.

Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: linux-pm@vger.kernel.org

show more ...

cpufreq: Add ARM_MT8173_CPUFREQ dependency on THERMAL

If ARM_MT8173_CPUFREQ is configured, and THERMAL is configured as module,
the following build error is seen for arm:allmodconfig and
arm64:allmo

cpufreq: Add ARM_MT8173_CPUFREQ dependency on THERMAL

If ARM_MT8173_CPUFREQ is configured, and THERMAL is configured as module,
the following build error is seen for arm:allmodconfig and
arm64:allmodconfig.

drivers/built-in.o: In function `mtk_cpufreq_ready':
:(.text+0x32a20c): undefined reference to `of_cpufreq_cooling_register'
drivers/built-in.o: In function `mtk_cpufreq_exit':
:(.text+0x32a420): undefined reference to `cpufreq_cooling_unregister'

The fix is similar to CPUFREQ_DT, but more restrictive since
ARM_MT8173_CPUFREQ can not be built as module.

Fixes: 1453863fb02a ("cpufreq: mediatek: Add MT8173 cpufreq driver")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

cpufreq: mediatek: Add MT8173 cpufreq driver

Mediatek MT8173 is an ARMv8 based quad-core (2*Cortex-A53 and
2*Cortex-A72) SoC with duall clusters. For each cluster, two voltage
inputs, Vproc and Vsra

cpufreq: mediatek: Add MT8173 cpufreq driver

Mediatek MT8173 is an ARMv8 based quad-core (2*Cortex-A53 and
2*Cortex-A72) SoC with duall clusters. For each cluster, two voltage
inputs, Vproc and Vsram are supplied by two regulators. For the big
cluster, two regulators come from different PMICs. In this case, when
scaling voltage inputs of the cluster, the voltages of two regulator
inputs need to be controlled by software explicitly under the SoC
specific limitation:

100mV < Vsram - Vproc < 200mV

which is called 'voltage tracking' mechanism. And when scaling the
frequency of cluster clock input, the input MUX need to be parented to
another "intermediate" stable PLL first and reparented to the original
PLL once the original PLL is stable at the target frequency. This patch
implements those mechanisms to enable CPU DVFS support for Mediatek
MT8173 SoC.

Signed-off-by: Pi-Cheng Chen <pi-cheng.chen@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

cpufreq: exynos: remove Exynos4x12 specific cpufreq driver support

Exynos4x12 based platforms have switched over to use generic
cpufreq driver for cpufreq functionality. So the Exynos
specific cpuf

cpufreq: exynos: remove Exynos4x12 specific cpufreq driver support

Exynos4x12 based platforms have switched over to use generic
cpufreq driver for cpufreq functionality. So the Exynos
specific cpufreq support for these platforms can be removed.

Also once Exynos4x12 based platforms support have been removed
the shared exynos-cpufreq driver is no longer needed and can
be deleted.

Based on the earlier work by Thomas Abraham.

Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>

show more ...

cpufreq: exynos: remove exynos5250 specific cpufreq driver support

Exynos5250 based platforms have switched over to use generic
cpufreq driver for cpufreq functionality. So the Exynos
specific cpufr

cpufreq: exynos: remove exynos5250 specific cpufreq driver support

Exynos5250 based platforms have switched over to use generic
cpufreq driver for cpufreq functionality. So the Exynos
specific cpufreq support for these platforms can be removed.

Cc: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Tested-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
[k.kozlowski: Rebased the patch around exynos-cpufreq.c]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>

show more ...

cpufreq: Add cpufreq driver for Tegra124

Add a new cpufreq driver for Tegra124. Instead of using the PLLX as
the CPU clocksource, switch immediately to the DFLL. It allows the use
of higher clock ra

cpufreq: Add cpufreq driver for Tegra124

Add a new cpufreq driver for Tegra124. Instead of using the PLLX as
the CPU clocksource, switch immediately to the DFLL. It allows the use
of higher clock rates, and will automatically scale the CPU voltage as
well. Besides the CPU clocksource switch, we let the cpufreq-dt driver
for all the cpufreq operations.

This driver also relies on the DFLL driver to fill the OPP table for the
CPU0 device, so that the cpufreq-dt driver knows what frequencies to
use.

Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: Mikko Perttunen <mikko.perttunen@kapsi.fi>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>

show more ...

cpufreq: tegra: Rename tegra-cpufreq to tegra20-cpufreq

The Tegra124 will use a different driver for frequency scaling, so
rename the old driver (which handles only Tegra20) appropriately.

Signed-o

cpufreq: tegra: Rename tegra-cpufreq to tegra20-cpufreq

The Tegra124 will use a different driver for frequency scaling, so
rename the old driver (which handles only Tegra20) appropriately.

Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: Mikko Perttunen <mikko.perttunen@kapsi.fi>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>

show more ...

cpufreq: exynos: remove Exynos4210 specific cpufreq driver support

Exynos4210 based platforms have switched over to use generic
cpufreq driver for cpufreq functionality. So the Exynos
specific cpufr

cpufreq: exynos: remove Exynos4210 specific cpufreq driver support

Exynos4210 based platforms have switched over to use generic
cpufreq driver for cpufreq functionality. So the Exynos
specific cpufreq support for these platforms can be removed.

Changes by Bartlomiej:
- dropped Exynos5250 support removal for now
- updated exynos-cpufreq.[c,h]

Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>

show more ...

cpufreq: arm_big_little: remove compile-time dependency on BIG_LITTLE

With the addition of switcher code, there's compile-time dependency on
BIG_LITTLE to get arm_big_little driver compiling on ARM6

cpufreq: arm_big_little: remove compile-time dependency on BIG_LITTLE

With the addition of switcher code, there's compile-time dependency on
BIG_LITTLE to get arm_big_little driver compiling on ARM64. Since ARM64
will never add support for bL switcher, it's better to remove the
dependency so that the driver can be reused on ARM64 platforms.

This patch adds stubs to remove BIG_LITTLE dependency in the driver.

Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

cpufreq: hisilicon: add acpu driver

Add acpu driver for hisilicon SoC, acpu is application processor
subsystem. Currently the acpu has the coupled clock domain for two
clusters, so this driver will

cpufreq: hisilicon: add acpu driver

Add acpu driver for hisilicon SoC, acpu is application processor
subsystem. Currently the acpu has the coupled clock domain for two
clusters, so this driver will directly use cpufreq-dt driver as
backend.

Signed-off-by: Leo Yan <leo.yan@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

cpufreq: exynos: allow modular build

The exynos cpufreq driver code recently gained a dependency on the
cooling code, which may be a loadable module. This breaks an ARM
allmodconfig build:

drivers/

cpufreq: exynos: allow modular build

The exynos cpufreq driver code recently gained a dependency on the
cooling code, which may be a loadable module. This breaks an ARM
allmodconfig build:

drivers/built-in.o: In function `exynos_cpufreq_probe':
:(.text+0x1748e8): undefined reference to `of_cpufreq_cooling_register'

To avoid this problem, change cpufreq Kconfig to allow the drivers
to be loadable modules as well and enforce a dependency on the
thermal module.

This change, in order to allow module builds on this cpufreq
driver, properly constructs the driver into a single module,
instead of several modules. The change also keeps the proper
platform dependency, and therefore, it wont load in platforms
that are not supposed to be loaded. The user will be able to
build the support for all platforms, or select which platforms
(s)he wants (as originally), except that now it can be a module,
instead.

Besides, it will still keep the driver only on those configs
that expect it to be on. And it won't compile/load on platforms
that it is not supposed to. It brings the config ARM_EXYNOS_CPU_FREQ_BOOST_SW
closer to this driver, so it looks better in the menuconfig.

We intentionally change ARM_EXYNOS5440_CPUFREQ to be tristate too, to
avoid future troubles.

Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-pm@vger.kernel.org
Cc: linux-samsung-soc@vger.kernel.org
Fixes: e725d26c4857 ("cpufreq: exynos: Use device tree to determine if cpufreq cooling should be registered")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

show more ...