clk: sunxi-ng: Add support for the sun6i RTC clocks

The RTC power domain in sun6i and newer SoCs manages the 16 MHz RC
oscillator (called "IOSC" or "osc16M") and the optional 32 kHz crystal
oscillat

clk: sunxi-ng: Add support for the sun6i RTC clocks

The RTC power domain in sun6i and newer SoCs manages the 16 MHz RC
oscillator (called "IOSC" or "osc16M") and the optional 32 kHz crystal
oscillator (called "LOSC" or "osc32k"). Starting with the H6, this power
domain also handles the 24 MHz DCXO (called variously "HOSC", "dcxo24M",
or "osc24M") as well. The H6 also adds a calibration circuit for IOSC.

Later SoCs introduce further variations on the design:
- H616 adds an additional mux for the 32 kHz fanout source.
- R329 adds an additional mux for the RTC timekeeping clock, a clock
for the SPI bus between power domains inside the RTC, and removes the
IOSC calibration functionality.

Take advantage of the CCU framework to handle this increased complexity.
This driver is intended to be a drop-in replacement for the existing RTC
clock provider. So some runtime adjustment of the clock parents is
needed, both to handle hardware differences, and to support the old
binding which omitted some of the input clocks.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220203021736.13434-6-samuel@sholland.org

show more ...

clk: sunxi-ng: Add support for the D1 SoC clocks

The D1 SoC contains a CCU and a R_CCU (PRCM CCU). Add support for them.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ri

clk: sunxi-ng: Add support for the D1 SoC clocks

The D1 SoC contains a CCU and a R_CCU (PRCM CCU). Add support for them.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20211119043545.4010-7-samuel@sholland.org

show more ...

clk: sunxi-ng: Allow the CCU core to be built as a module

Like the individual CCU drivers, it can be beneficial for memory
consumption of cross-platform configurations to only load the CCU core
on t

clk: sunxi-ng: Allow the CCU core to be built as a module

Like the individual CCU drivers, it can be beneficial for memory
consumption of cross-platform configurations to only load the CCU core
on the relevant platform. For example, a generic arm64 kernel sees the
following improvement when building the CCU core and drivers as modules:

before:
text data bss dec hex filename
13882360 5251670 360800 19494830 12977ae vmlinux

after:
text data bss dec hex filename
13734787 5086442 360800 19182029 124b1cd vmlinux

So the result is a 390KB total reduction in kernel image size.

The one early clock provider (sun5i) requires the core to be built in.

Now that loading the MMC driver will trigger loading the CCU core, the
MMC timing mode functions do not need a compile-time fallback.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20211119033338.25486-5-samuel@sholland.org

show more ...

clk: sunxi-ng: Allow drivers to be built as modules

While it is useful to build all of the CCU drivers at once, only 1-3 of
them will be loaded at a time, or possibly none of them if the kernel is
b

clk: sunxi-ng: Allow drivers to be built as modules

While it is useful to build all of the CCU drivers at once, only 1-3 of
them will be loaded at a time, or possibly none of them if the kernel is
booted on a non-sunxi platform. These CCU drivers are relatively large;
32-bit drivers have 30-50k of data each, while the 64-bit ones are
50-75k due to the increased pointer overhead. About half of that data
comes from relocations. Let's allow the user to build these drivers as
modules so only the necessary data is loaded.

As a first step, convert the CCUs that are already platform drivers.

When the drivers are built as modules, normally the file name becomes
the module name. However, the current file names are inconsistent with
the <platform>-<peripheral> name used everywhere else: the devicetree
bindings, the platform driver names, and the Kconfig symbols. Use
Makfile logic to rename the modules so they follow the usual pattern.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20211119033338.25486-3-samuel@sholland.org

show more ...

clk: sunxi-ng: Add support for the Allwinner H616 CCU

While the clocks are fairly similar to the H6, many differ in tiny
details, so a separate clock driver seems indicated.

Derived from the H6 clo

clk: sunxi-ng: Add support for the Allwinner H616 CCU

While the clocks are fairly similar to the H6, many differ in tiny
details, so a separate clock driver seems indicated.

Derived from the H6 clock driver, and adjusted according to the manual.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210127172500.13356-4-andre.przywara@arm.com

show more ...

clk: sunxi-ng: add support for the Allwinner A100 CCU

Add support for a100 in the sunxi-ng CCU framework.

Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Signed-off-by: Maxime Ripard <maxime@ce

clk: sunxi-ng: add support for the Allwinner A100 CCU

Add support for a100 in the sunxi-ng CCU framework.

Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1eb41bf6c966a0e54820200650d27a5d4f2ac160.1595572867.git.frank@allwinnertech.com

show more ...

clk: sunxi-ng: add support for suniv F1C100s SoC

The suniv F1C100s SoC (the chip in some new F-series products of
Allwinner)
has a CCU which seems to be a stripped version of the CCU in SoCs after
s

clk: sunxi-ng: add support for suniv F1C100s SoC

The suniv F1C100s SoC (the chip in some new F-series products of
Allwinner)
has a CCU which seems to be a stripped version of the CCU in SoCs after
sun6i.

Add support for the CCU.

Signed-off-by: Mesih Kilinc <mesihkilinc@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

show more ...

clk: sunxi-ng: replace lib-y with obj-y

We had commit 06e226c7fb23 ("clk: sunxi-ng: Move all clock types to a
library") and commit 799c43415442 ("kbuild: thin archives make default
for all archs") i

clk: sunxi-ng: replace lib-y with obj-y

We had commit 06e226c7fb23 ("clk: sunxi-ng: Move all clock types to a
library") and commit 799c43415442 ("kbuild: thin archives make default
for all archs") in the same development cycle, from different trees.

With migration to the thin archive, the entire drivers/clk/sunxi-ng/lib.a
is linked to the vmlinux. This does not break build, but we do not get
any size saving.

However, we do not need to go back to the individual Kconfig options.
The default configuration pulls in all (or most) of the CCU parts anyway.
Also, once we enable CONFIG_LD_DEAD_CODE_DATA_ELIMINATION, we can simply
list all files with obj-y, and the linker will drop all unused functions
by itself.

After the long discussion [1], people there agreed to fix this, but
nobody sent a patch after all. I am doing it now.

I lifted up CONFIG_SUNXI_CCU to drivers/clk/Makefile because everything
in drivers/clk/sunxi-ng/ depends on SUNXI_CCU.

[1] https://patchwork.kernel.org/patch/9796521/

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

show more ...

clk: sunxi-ng: add support for H6 PRCM CCU

The H6 has clock/reset controls in PRCM part, like old SoCs such as H3
and A64. However, the PRCM CCU is rearranged; the register arragement
is now similar

clk: sunxi-ng: add support for H6 PRCM CCU

The H6 has clock/reset controls in PRCM part, like old SoCs such as H3
and A64. However, the PRCM CCU is rearranged; the register arragement
is now similar to the main CCU of H6, and the PRCM now has two APB
buses to control -- one is clocked from AHB clock derivde from AR100
clock, the other is clocked from the same mux with AR100 clock.
Therefore a new driver is written for it.

As there's no official document about the PRCM in H6, all the information
are indirectly collected from BSP and parts of the document, and the
information source is noted as comments in the driver's source code. If
reliable information is provided furtherly, the driver needs to be
rechecked.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

show more ...

clk: sunxi-ng: add support for the Allwinner H6 CCU

The Allwinner H6 SoC has a CCU which has been largely rearranged.

Add support for it in the sunxi-ng CCU framework.

Signed-off-by: Icenowy Zheng

clk: sunxi-ng: add support for the Allwinner H6 CCU

The Allwinner H6 SoC has a CCU which has been largely rearranged.

Add support for it in the sunxi-ng CCU framework.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

show more ...

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.

For non */uapi/* files that summary was:

SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139

and resulted in the first patch in this series.

If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:

SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930

and resulted in the second patch in this series.

- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:

SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1

and that resulted in the third patch in this series.

- when the two scanners agreed on the detected license(s), that became
the concluded license(s).

- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.

- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).

- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.

- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct

This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

clk: sunxi-ng: Add sigma-delta modulation support

Sigma-delta modulation is supported for some PLLs. This allows
fractional-N multipliers to be used. In reality we don't know
how to configure the in

clk: sunxi-ng: Add sigma-delta modulation support

Sigma-delta modulation is supported for some PLLs. This allows
fractional-N multipliers to be used. In reality we don't know
how to configure the individual settings for it. However we can
copy existing settings from the vendor kernel to support clock
rates that cannot be generated from integer factors, but are
really desired. The vendor kernel only uses this for the audio
PLL clock, and only on the latest chips.

This patch adds a new class of clocks, along with helper functions.
It is intended to be merged into N-M-factor style clocks as a
feature, much like fractional clocks.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

show more ...

clk: sunxi-ng: Add interface to query or configure MMC timing modes.

Starting with the A83T SoC, Allwinner introduced a new timing mode for
its MMC clocks. The new mode changes how the MMC controlle

clk: sunxi-ng: Add interface to query or configure MMC timing modes.

Starting with the A83T SoC, Allwinner introduced a new timing mode for
its MMC clocks. The new mode changes how the MMC controller sample and
output clocks are delayed to match chip and board specifics. There are
two controls for this, one on the CCU side controlling how the clocks
behave, and one in the MMC controller controlling what inputs to take
and how to route them.

In the old mode, the MMC clock had 2 child clocks providing the output
and sample clocks, which could be delayed by a number of clock cycles
measured from the MMC clock's parent.

With the new mode, the 2 delay clocks are no longer active. Instead,
the delays and associated controls are moved into the MMC controller.
The output of the MMC clock is also halved.

The difference in how things are wired between the modes means that the
clock controls and the MMC controls must match. To achieve this in a
clear, explicit way, we introduce two functions for the MMC driver to
use: one queries the hardware for the current mode set, and the other
allows the MMC driver to request a mode.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

show more ...

clk: sunxi-ng: Add sun4i/sun7i CCU driver

Introduce a clock controller driver for sun4i A10 and sun7i A20
series SoCs.

Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxi

clk: sunxi-ng: Add sun4i/sun7i CCU driver

Introduce a clock controller driver for sun4i A10 and sun7i A20
series SoCs.

Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

show more ...

clk: sunxi-ng: support R40 SoC

Allwinner R40 SoC have a clock controller module in the style of the
SoCs beyond sun6i, however, it's more rich and complex.

Add support for it.

Signed-off-by: Iceno

clk: sunxi-ng: support R40 SoC

Allwinner R40 SoC have a clock controller module in the style of the
SoCs beyond sun6i, however, it's more rich and complex.

Add support for it.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

show more ...

clk: sunxi-ng: Move all clock types to a library

We've run into kconfig missing dependency errors in the sunxi-ng
code a couple times now. Each time the fix is to find the missing
select statement a

clk: sunxi-ng: Move all clock types to a library

We've run into kconfig missing dependency errors in the sunxi-ng
code a couple times now. Each time the fix is to find the missing
select statement and add it to the Kconfig entry for a particular
SoC driver. Given that all this code is builtin (non-modular) we
don't need to do this complicated dependency tracking in Kconfig.
Instead we can move all the "library"ish code to be compiled as
lib-y instead of obj-y, let the linker throw away unused code in
the resulting vmlinux, and drop all the Kconfig stuff we use to
track clock types.

Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
[Maxime: added lib.a to obj-y, added the comment]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

show more ...

clk: sunxi-ng: Add driver for A83T CCU

The A83T clock control unit is a hybrid of some new style clock designs
from the A80, and old style layout from the other Allwinner SoCs.

Like the A80, the So

clk: sunxi-ng: Add driver for A83T CCU

The A83T clock control unit is a hybrid of some new style clock designs
from the A80, and old style layout from the other Allwinner SoCs.

Like the A80, the SoC does not have a low speed 32.768 kHz oscillator.
Unlike the A80, there is no clock input either. The only low speed clock
available is the internal oscillator which runs at around 16 MHz,
divided by 512, yielding a low speed clock around 31.250 kHz.

Also, the MMC2 module clock supports switching to a "new timing" mode.
This mode divides the clock output by half, and disables the CCU based
clock delays. The MMC controller must be configure to the same mode,
and then use its internal clock delays.

This driver does not support runtime switching of the timing modes.
Instead, the new timing mode is enforced at probe time. Consumers can
check which mode is active by trying to get the current phase delay
of the MMC2 phase clocks, which will return -ENOTSUPP if the new
timing mode is active.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

show more ...

clk: sunxi-ng: add support for DE2 CCU

The "Display Engine 2.0" in Allwinner newer SoCs contains a clock
management unit for its subunits, like the DE CCU in A80.

Add a sunxi-ng style driver for it

clk: sunxi-ng: add support for DE2 CCU

The "Display Engine 2.0" in Allwinner newer SoCs contains a clock
management unit for its subunits, like the DE CCU in A80.

Add a sunxi-ng style driver for it.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

show more ...

clk: sunxi-ng: add support for PRCM CCUs

SoCs after A31 has a clock controller module in the PRCM part.

Support the clock controller module on H3/5 and A64 now.

Signed-off-by: Icenowy Zheng <iceno

clk: sunxi-ng: add support for PRCM CCUs

SoCs after A31 has a clock controller module in the PRCM part.

Support the clock controller module on H3/5 and A64 now.

Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

show more ...

clk: sunxi-ng: Add A80 Display Engine CCU

With the A80 SoC, Allwinner grouped and moved some subsystem specific
clock controls to a separate address space, and possibly separate
hardware block.

One

clk: sunxi-ng: Add A80 Display Engine CCU

With the A80 SoC, Allwinner grouped and moved some subsystem specific
clock controls to a separate address space, and possibly separate
hardware block.

One such subsystem is the display engine. The main clock control unit
now only has 1 set of bus gate, dram gate, module clock, and reset
control for the entire display subsystem. These feed into a secondary
clock control unit, which has controls for each individual module
of the display pipeline. This block is not documented in the user
manual. Allwinner's kernel was used as the reference.

Add support for the display engine clock controls found on the A80.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

show more ...

clk: sunxi-ng: Add A80 USB CCU

Add support for the USB clock controls found on the A80.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Rip

clk: sunxi-ng: Add A80 USB CCU

Add support for the USB clock controls found on the A80.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

show more ...

clk: sunxi-ng: Add A80 CCU

Add support for the main clock unit found in the A80. Some clocks were
not documented in the released user manual, but were found in the
official kernel from Allwinner. Th

clk: sunxi-ng: Add A80 CCU

Add support for the main clock unit found in the A80. Some clocks were
not documented in the released user manual, but were found in the
official kernel from Allwinner. These include controls for the I2S,
SPDIF, SATA, and eDP blocks.

Note that on the A80, some subsystems have separate clock controllers
downstream of the main clock unit. These include the MMC, USB, and
display engine subsystems.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

show more ...

clk: sunxi-ng: Add sun5i CCU driver

The Allwinner A10s, A13, R8 and NextThing GR8 are all based on the same
silicon, and all share the same clocks.

However, they're not packaged in the same way, an

clk: sunxi-ng: Add sun5i CCU driver

The Allwinner A10s, A13, R8 and NextThing GR8 are all based on the same
silicon, and all share the same clocks.

However, they're not packaged in the same way, and therefore not all the
controllers are actually available on all these SoCs.

Introduce a clock controller driver for all these SoCs with different
compatibles to take that into account.

Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

show more ...

clk: sunxi-ng: add support for V3s CCU

V3s has a similar but cut-down CCU to H3. Some muxes, especially clocks
about CSI, are different, which makes it to need a new CCU driver.

Add such a new driv

clk: sunxi-ng: add support for V3s CCU

V3s has a similar but cut-down CCU to H3. Some muxes, especially clocks
about CSI, are different, which makes it to need a new CCU driver.

Add such a new driver for it.

Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

show more ...

clk: sunxi-ng: Add A64 clocks

Add the A64 CCU clocks set.

Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.c

clk: sunxi-ng: Add A64 clocks

Add the A64 CCU clocks set.

Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

show more ...