powerpc/mm: Fix build error with FLATMEM book3s64 config

The current value of MAX_PHYSMEM_BITS cannot work with 32 bit configs.
We used to have MAX_PHYSMEM_BITS not defined without SPARS

powerpc/mm: Fix build error with FLATMEM book3s64 config

The current value of MAX_PHYSMEM_BITS cannot work with 32 bit configs.
We used to have MAX_PHYSMEM_BITS not defined without SPARSEMEM and 32
bit configs never expected a value to be set for MAX_PHYSMEM_BITS.

Dependent code such as zsmalloc derived the right values based on other
fields. Instead of finding a value that works with different configs,
use new values only for book3s_64. For 64 bit booke, use the definition
of MAX_PHYSMEM_BITS as per commit a7df61a0e2b6 ("[PATCH] ppc64: Increase sparsemem defaults")
That change was done in 2005 and hopefully will work with book3e 64.

Fixes: 8bc086899816 ("powerpc/mm: Only define MAX_PHYSMEM_BITS in SPARSEMEM configurations")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

show more ...

powerpc/64s: Implement KUAP for Radix MMU

Kernel Userspace Access Prevention utilises a feature of the Radix MMU
which disallows read and write access to userspace addresses. By
util

powerpc/64s: Implement KUAP for Radix MMU

Kernel Userspace Access Prevention utilises a feature of the Radix MMU
which disallows read and write access to userspace addresses. By
utilising this, the kernel is prevented from accessing user data from
outside of trusted paths that perform proper safety checks, such as
copy_{to/from}_user() and friends.

Userspace access is disabled from early boot and is only enabled when
performing an operation like copy_{to/from}_user(). The register that
controls this (AMR) does not prevent userspace from accessing itself,
so there is no need to save and restore when entering and exiting
userspace.

When entering the kernel from the kernel we save AMR and if it is not
blocking user access (because eg. we faulted doing a user access) we
reblock user access for the duration of the exception (ie. the page
fault) and then restore the AMR when returning back to the kernel.

This feature can be tested by using the lkdtm driver (CONFIG_LKDTM=y)
and performing the following:

# (echo ACCESS_USERSPACE) > [debugfs]/provoke-crash/DIRECT

If enabled, this should send SIGSEGV to the thread.

We also add paranoid checking of AMR in switch and syscall return
under CONFIG_PPC_KUAP_DEBUG.

Co-authored-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

show more ...

powerpc/mm: Define MAX_PHYSMEM_BITS for all 64-bit configs

The recent commit 8bc086899816 ("powerpc/mm: Only define
MAX_PHYSMEM_BITS in SPARSEMEM configurations") removed our definition

powerpc/mm: Define MAX_PHYSMEM_BITS for all 64-bit configs

The recent commit 8bc086899816 ("powerpc/mm: Only define
MAX_PHYSMEM_BITS in SPARSEMEM configurations") removed our definition
of MAX_PHYSMEM_BITS when SPARSEMEM is disabled.

This inadvertently broke some 64-bit FLATMEM using configs with eg:

arch/powerpc/include/asm/book3s/64/mmu-hash.h:584:6: error: "MAX_PHYSMEM_BITS" is not defined, evaluates to 0
#if (MAX_PHYSMEM_BITS > MAX_EA_BITS_PER_CONTEXT)
^~~~~~~~~~~~~~~~

Fix it by making sure we define MAX_PHYSMEM_BITS for all 64-bit
configs regardless of SPARSEMEM.

Fixes: 8bc086899816 ("powerpc/mm: Only define MAX_PHYSMEM_BITS in SPARSEMEM configurations")
Reported-by: Andreas Schwab <schwab@linux-m68k.org>
Reported-by: Hugh Dickins <hughd@google.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

show more ...

powerpc/mm: Only define MAX_PHYSMEM_BITS in SPARSEMEM configurations

MAX_PHYSMEM_BITS only needs to be defined if CONFIG_SPARSEMEM is
enabled, and that was the case before commit 4ffe713

powerpc/mm: Only define MAX_PHYSMEM_BITS in SPARSEMEM configurations

MAX_PHYSMEM_BITS only needs to be defined if CONFIG_SPARSEMEM is
enabled, and that was the case before commit 4ffe713b7587
("powerpc/mm: Increase the max addressable memory to 2PB").

On 32-bit systems, where CONFIG_SPARSEMEM is not enabled, we now
define it as 46. That is larger than the real number of physical
address bits, and breaks calculations in zsmalloc:

mm/zsmalloc.c:130:49: warning: right shift count is negative
MAX(32, (ZS_MAX_PAGES_PER_ZSPAGE << PAGE_SHIFT >> OBJ_INDEX_BITS))
^~
...
mm/zsmalloc.c:253:21: error: variably modified 'size_class' at file scope
struct size_class *size_class[ZS_SIZE_CLASSES];
^~~~~~~~~~

Fixes: 4ffe713b7587 ("powerpc/mm: Increase the max addressable memory to 2PB")
Cc: stable@vger.kernel.org # v4.20+
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

show more ...

powerpc/mmu: add is_strict_kernel_rwx() helper

Add a helper to know whether STRICT_KERNEL_RWX is enabled.

This is based on rodata_enabled flag which is defined only
when CONFIG_

powerpc/mmu: add is_strict_kernel_rwx() helper

Add a helper to know whether STRICT_KERNEL_RWX is enabled.

This is based on rodata_enabled flag which is defined only
when CONFIG_STRICT_KERNEL_RWX is selected.

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

show more ...

powerpc: simplify BDI switch

There is no reason to re-read each time the pointer at
location 0xf0 as it is fixed and known.

Signed-off-by: Christophe Leroy <christophe.leroy@c-s

powerpc: simplify BDI switch

There is no reason to re-read each time the pointer at
location 0xf0 as it is fixed and known.

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

show more ...

powerpc/mm: Eliminate not possible mmu features at compile time

Depending on the CONFIG selected, many of the MMU features are
not possible. Lets only get the possible ones in MMU_FTRS_P

powerpc/mm: Eliminate not possible mmu features at compile time

Depending on the CONFIG selected, many of the MMU features are
not possible. Lets only get the possible ones in MMU_FTRS_POSSIBLE.

This allows gcc to get rid at compile time of code related to
not possible features.

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

show more ...

powerpc/mm: move platform specific mmu-xxx.h in platform directories

The purpose of this patch is to move platform specific
mmu-xxx.h files in platform directories like pte-xxx.h files.

powerpc/mm: move platform specific mmu-xxx.h in platform directories

The purpose of this patch is to move platform specific
mmu-xxx.h files in platform directories like pte-xxx.h files.

In the meantime this patch creates common nohash and
nohash/32 + nohash/64 mmu.h files for future common parts.

Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

show more ...

powerpc: change CONFIG_PPC_STD_MMU_32 to CONFIG_PPC_BOOK3S_32

Today we have:

config PPC_BOOK3S_32
bool "512x/52xx/6xx/7xx/74xx/82xx/83xx/86xx"
[depends on PP

powerpc: change CONFIG_PPC_STD_MMU_32 to CONFIG_PPC_BOOK3S_32

Today we have:

config PPC_BOOK3S_32
bool "512x/52xx/6xx/7xx/74xx/82xx/83xx/86xx"
[depends on PPC32 within a choice]

config PPC_BOOK3S
def_bool y
depends on PPC_BOOK3S_32 || PPC_BOOK3S_64

config PPC_STD_MMU
def_bool y
depends on PPC_BOOK3S

config PPC_STD_MMU_32
def_bool y
depends on PPC_STD_MMU && PPC32

PPC_STD_MMU_32 is therefore redundant with PPC_BOOK3S_32.

In order to make the code clearer, lets use preferably PPC_BOOK3S_32.
This will allow to remove CONFIG_PPC_STD_MMU_32 in a later patch.

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

show more ...

powerpc: change CONFIG_6xx to CONFIG_PPC_BOOK3S_32

Today we have:

config PPC_BOOK3S_32
bool "512x/52xx/6xx/7xx/74xx/82xx/83xx/86xx"
[depends on PPC32 within

powerpc: change CONFIG_6xx to CONFIG_PPC_BOOK3S_32

Today we have:

config PPC_BOOK3S_32
bool "512x/52xx/6xx/7xx/74xx/82xx/83xx/86xx"
[depends on PPC32 within a choice]

config PPC_BOOK3S
def_bool y
depends on PPC_BOOK3S_32 || PPC_BOOK3S_64

config 6xx
def_bool y
depends on PPC32 && PPC_BOOK3S

6xx is therefore redundant with PPC_BOOK3S_32.

In order to make the code clearer, lets use preferably PPC_BOOK3S_32.
This will allow to remove CONFIG_6xx in a later patch.

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

show more ...

powerpc/mm: Increase the max addressable memory to 2PB

Currently we limit the max addressable memory to 128TB. This patch increase the
limit to 2PB. We can have devices like nvdimm which

powerpc/mm: Increase the max addressable memory to 2PB

Currently we limit the max addressable memory to 128TB. This patch increase the
limit to 2PB. We can have devices like nvdimm which adds memory above 512TB
limit.

We still don't support regular system ram above 512TB. One of the challenge with
that is the percpu allocator, that allocates per node memory and use the max
distance between them as the percpu offsets. This means with large gap in
address space ( system ram above 1PB) we will run out of vmalloc space to map
the percpu allocation.

In order to support addressable memory above 512TB, kernel should be able to
linear map this range. To do that with hash translation we now add 4 context
to kernel linear map region. Our per context addressable range is 512TB. We
still keep VMALLOC and VMEMMAP region to old size. SLB miss handlers is updated
to validate these limit.

We also limit this update to SPARSEMEM_VMEMMAP and SPARSEMEM_EXTREME

Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

show more ...

powerpc: clean inclusions of asm/feature-fixups.h

files not using feature fixup don't need asm/feature-fixups.h
files using feature fixup need asm/feature-fixups.h

Signed-off-by

powerpc: clean inclusions of asm/feature-fixups.h

files not using feature fixup don't need asm/feature-fixups.h
files using feature fixup need asm/feature-fixups.h

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

show more ...

powerpc: move ASM_CONST and stringify_in_c() into asm-const.h

This patch moves ASM_CONST() and stringify_in_c() into
dedicated asm-const.h, then cleans all related inclusions.

S

powerpc: move ASM_CONST and stringify_in_c() into asm-const.h

This patch moves ASM_CONST() and stringify_in_c() into
dedicated asm-const.h, then cleans all related inclusions.

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: asm-compat.h should include asm-const.h]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

show more ...

powerpc/64s: Remove POWER4 support

POWER4 has been broken since at least the change 49d09bf2a6
("powerpc/64s: Optimise MSR handling in exception handling"), which
requires mtmsrd L=1

powerpc/64s: Remove POWER4 support

POWER4 has been broken since at least the change 49d09bf2a6
("powerpc/64s: Optimise MSR handling in exception handling"), which
requires mtmsrd L=1 support. This was introduced in ISA v2.01, and
POWER4 supports ISA v2.00.

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

show more ...

powerpc: introduce get_mm_addr_key() helper

get_mm_addr_key() helper returns the pkey associated with
an address corresponding to a given mm_struct.

Signed-off-by: Ram Pai <linu

powerpc: introduce get_mm_addr_key() helper

get_mm_addr_key() helper returns the pkey associated with
an address corresponding to a given mm_struct.

Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

show more ...

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

Many source files in the tree are missing licensing information, which
makes it harder for compliance tools

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.

For non */uapi/* files that summary was:

SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139

and resulted in the first patch in this series.

If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:

SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930

and resulted in the second patch in this series.

- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:

SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1

and that resulted in the third patch in this series.

- when the two scanners agreed on the detected license(s), that became
the concluded license(s).

- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.

- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).

- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.

- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct

This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

powerpc/mm/hash: Support 68 bit VA

Inorder to support large effective address range (512TB), we want to
increase the virtual address bits to 68. But we do have platforms like
p4 and

powerpc/mm/hash: Support 68 bit VA

Inorder to support large effective address range (512TB), we want to
increase the virtual address bits to 68. But we do have platforms like
p4 and p5 that can only do 65 bit VA. We support those platforms by
limiting context bits on them to 16.

The protovsid -> vsid conversion is verified to work with both 65 and 68
bit va values. I also documented the restrictions in a table format as
part of code comments.

Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

show more ...

Merge tag 'powerpc-4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux

Pull powerpc updates from Michael Ellerman:
"Highlights include:

- Support for dire

Merge tag 'powerpc-4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux

Pull powerpc updates from Michael Ellerman:
"Highlights include:

- Support for direct mapped LPC on POWER9, giving Linux direct access
to devices that may be on there such as a UART.

- Memory hotplug support for the Power9 Radix MMU.

- Add new AUX vectors describing the processor's cache geometry, to
be used by glibc.

- The ability for a guest to ask the hypervisor to resize the guest's
hash table, and in addition support for doing so automatically when
memory is hotplugged into/out-of the guest. This allows the hash
table to be sized based on the current memory usage of the guest,
rather than the maximum possible memory usage.

- Implementation of optprobes (kprobe optimisation) for powerpc.

In addition there's the topic branch shared with the KVM tree, which
includes support for guests to use the Radix MMU on Power9.

Thanks to:
Alistair Popple, Andrew Donnellan, Aneesh Kumar K.V, Anju T, Anton
Blanchard, Benjamin Herrenschmidt, Chris Packham, Daniel Axtens,
Daniel Borkmann, David Gibson, Finn Thain, Gautham R. Shenoy, Gavin
Shan, Greg Kurz, Joel Stanley, John Allen, Madhavan Srinivasan,
Mahesh Salgaonkar, Markus Elfring, Michael Neuling, Nathan Fontenot,
Naveen N. Rao, Nicholas Piggin, Paul Mackerras, Ravi Bangoria, Reza
Arbab, Shailendra Singh, Vaibhav Jain, Wei Yongjun"

* tag 'powerpc-4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (129 commits)
powerpc/mm/radix: Skip ptesync in pte update helpers
powerpc/mm/radix: Use ptep_get_and_clear_full when clearing pte for full mm
powerpc/mm/radix: Update pte update sequence for pte clear case
powerpc/mm: Update PROTFAULT handling in the page fault path
powerpc/xmon: Fix data-breakpoint
powerpc/mm: Fix build break with BOOK3S_64=n and MEMORY_HOTPLUG=y
powerpc/mm: Fix build break when CMA=n && SPAPR_TCE_IOMMU=y
powerpc/mm: Fix build break with RADIX=y & HUGETLBFS=n
powerpc/pseries: Fix typo in parameter description
powerpc/kprobes: Remove kprobe_exceptions_notify()
kprobes: Introduce weak variant of kprobe_exceptions_notify()
powerpc/ftrace: Fix confusing help text for DISABLE_MPROFILE_KERNEL
powerpc/powernv: Fix opal_exit tracepoint opcode
powerpc: Add a prototype for mcount() so it can be versioned
powerpc: Drop GPL from of_node_to_nid() export to match other arches
powerpc/kprobes: Optimize kprobe in kretprobe_trampoline()
powerpc/kprobes: Implement Optprobes
powerpc/kprobes: Fixes for kprobe_lookup_name() on BE
powerpc: Add helper to check if offset is within relative branch range
powerpc/bpf: Introduce __PPC_SH64()
...

show more ...

powerpc/mm: Add MMU_FTR_KERNEL_RO to possible feature mask

Without this we will always find the feature disabled.

Fixes: 984d7a1ec6 ("powerpc/mm: Fixup kernel read only mapping")

powerpc/mm: Add MMU_FTR_KERNEL_RO to possible feature mask

Without this we will always find the feature disabled.

Fixes: 984d7a1ec6 ("powerpc/mm: Fixup kernel read only mapping")
Cc: stable@vger.kernel.org # v4.7+
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

show more ...

powerpc: Fix build failure with clang due to BUILD_BUG_ON()

Anton says: In commit 4db7327194db ("powerpc: Add option to use jump
label for cpu_has_feature()") and commit c12e6f24d413 ("p

powerpc: Fix build failure with clang due to BUILD_BUG_ON()

Anton says: In commit 4db7327194db ("powerpc: Add option to use jump
label for cpu_has_feature()") and commit c12e6f24d413 ("powerpc: Add
option to use jump label for mmu_has_feature()") we added:

BUILD_BUG_ON(!__builtin_constant_p(feature))

to cpu_has_feature() and mmu_has_feature() in order to catch usage
issues (such as cpu_has_feature(cpu_has_feature(X), which has happened
once in the past). Unfortunately LLVM isn't smart enough to resolve
this, and it errors out.

I work around it in my clang/LLVM builds of the kernel, but I have just
discovered that it causes a lot of issues for the bcc (eBPF) trace tool
(which uses LLVM).

For now just #ifdef it away for clang builds.

Fixes: 4db7327194db ("powerpc: Add option to use jump label for cpu_has_feature()")
Fixes: c12e6f24d413 ("powerpc: Add option to use jump label for mmu_has_feature()")
Cc: stable@vger.kernel.org # v4.8+
Reported-by: Anton Blanchard <anton@samba.org>
Tested-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

show more ...

Merge tag 'powerpc-4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux

Pull powerpc updates from Michael Ellerman:
"Highlights include:

- Support for the

Merge tag 'powerpc-4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux

Pull powerpc updates from Michael Ellerman:
"Highlights include:

- Support for the kexec_file_load() syscall, which is a prereq for
secure and trusted boot.

- Prevent kernel execution of userspace on P9 Radix (similar to
SMEP/PXN).

- Sort the exception tables at build time, to save time at boot, and
store them as relative offsets to save space in the kernel image &
memory.

- Allow building the kernel with thin archives, which should allow us
to build an allyesconfig once some other fixes land.

- Build fixes to allow us to correctly rebuild when changing the
kernel endian from big to little or vice versa.

- Plumbing so that we can avoid doing a full mm TLB flush on P9
Radix.

- Initial stack protector support (-fstack-protector).

- Support for dumping the radix (aka. Linux) and hash page tables via
debugfs.

- Fix an oops in cxl coredump generation when cxl_get_fd() is used.

- Freescale updates from Scott: "Highlights include 8xx hugepage
support, qbman fixes/cleanup, device tree updates, and some misc
cleanup."

- Many and varied fixes and minor enhancements as always.

Thanks to:
Alexey Kardashevskiy, Andrew Donnellan, Aneesh Kumar K.V, Anshuman
Khandual, Anton Blanchard, Balbir Singh, Bartlomiej Zolnierkiewicz,
Christophe Jaillet, Christophe Leroy, Denis Kirjanov, Elimar
Riesebieter, Frederic Barrat, Gautham R. Shenoy, Geliang Tang, Geoff
Levand, Jack Miller, Johan Hovold, Lars-Peter Clausen, Libin,
Madhavan Srinivasan, Michael Neuling, Nathan Fontenot, Naveen N.
Rao, Nicholas Piggin, Pan Xinhui, Peter Senna Tschudin, Rashmica
Gupta, Rui Teng, Russell Currey, Scott Wood, Simon Guo, Suraj
Jitindar Singh, Thiago Jung Bauermann, Tobias Klauser, Vaibhav Jain"

[ And thanks to Michael, who took time off from a new baby to get this
pull request done. - Linus ]

* tag 'powerpc-4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (174 commits)
powerpc/fsl/dts: add FMan node for t1042d4rdb
powerpc/fsl/dts: add sg_2500_aqr105_phy4 alias on t1024rdb
powerpc/fsl/dts: add QMan and BMan nodes on t1024
powerpc/fsl/dts: add QMan and BMan nodes on t1023
soc/fsl/qman: test: use DEFINE_SPINLOCK()
powerpc/fsl-lbc: use DEFINE_SPINLOCK()
powerpc/8xx: Implement support of hugepages
powerpc: get hugetlbpage handling more generic
powerpc: port 64 bits pgtable_cache to 32 bits
powerpc/boot: Request no dynamic linker for boot wrapper
soc/fsl/bman: Use resource_size instead of computation
soc/fsl/qe: use builtin_platform_driver
powerpc/fsl_pmc: use builtin_platform_driver
powerpc/83xx/suspend: use builtin_platform_driver
powerpc/ftrace: Fix the comments for ftrace_modify_code
powerpc/perf: macros for power9 format encoding
powerpc/perf: power9 raw event format encoding
powerpc/perf: update attribute_group data structure
powerpc/perf: factor out the event format field
powerpc/mm/iommu, vfio/spapr: Put pages on VFIO container shutdown
...

show more ...

Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/scottwood/linux into next

Freescale updates from Scott:

"Highlights include 8xx hugepage support, qbman fixes/cl

Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/scottwood/linux into next

Freescale updates from Scott:

"Highlights include 8xx hugepage support, qbman fixes/cleanup, device
tree updates, and some misc cleanup."

show more ...

Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm

Pull KVM updates from Paolo Bonzini:
"Small release, the most interesting stuff is x86 nested virt
improvements.

Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm

Pull KVM updates from Paolo Bonzini:
"Small release, the most interesting stuff is x86 nested virt
improvements.

x86:
- userspace can now hide nested VMX features from guests
- nested VMX can now run Hyper-V in a guest
- support for AVX512_4VNNIW and AVX512_FMAPS in KVM
- infrastructure support for virtual Intel GPUs.

PPC:
- support for KVM guests on POWER9
- improved support for interrupt polling
- optimizations and cleanups.

s390:
- two small optimizations, more stuff is in flight and will be in
4.11.

ARM:
- support for the GICv3 ITS on 32bit platforms"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (94 commits)
arm64: KVM: pmu: Reset PMSELR_EL0.SEL to a sane value before entering the guest
KVM: arm/arm64: timer: Check for properly initialized timer on init
KVM: arm/arm64: vgic-v2: Limit ITARGETSR bits to number of VCPUs
KVM: x86: Handle the kthread worker using the new API
KVM: nVMX: invvpid handling improvements
KVM: nVMX: check host CR3 on vmentry and vmexit
KVM: nVMX: introduce nested_vmx_load_cr3 and call it on vmentry
KVM: nVMX: propagate errors from prepare_vmcs02
KVM: nVMX: fix CR3 load if L2 uses PAE paging and EPT
KVM: nVMX: load GUEST_EFER after GUEST_CR0 during emulated VM-entry
KVM: nVMX: generate MSR_IA32_CR{0,4}_FIXED1 from guest CPUID
KVM: nVMX: fix checks on CR{0,4} during virtual VMX operation
KVM: nVMX: support restore of VMX capability MSRs
KVM: nVMX: generate non-true VMX MSRs based on true versions
KVM: x86: Do not clear RFLAGS.TF when a singlestep trap occurs.
KVM: x86: Add kvm_skip_emulated_instruction and use it.
KVM: VMX: Move skip_emulated_instruction out of nested_vmx_check_vmcs12
KVM: VMX: Reorder some skip_emulated_instruction calls
KVM: x86: Add a return value to kvm_emulate_cpuid
KVM: PPC: Book3S: Move prototypes for KVM functions into kvm_ppc.h
...

show more ...

powerpc/8xx: Implement support of hugepages

8xx uses a two level page table with two different linux page size
support (4k and 16k). 8xx also support two different hugepage sizes
512

powerpc/8xx: Implement support of hugepages

8xx uses a two level page table with two different linux page size
support (4k and 16k). 8xx also support two different hugepage sizes
512k and 8M. In order to support them on linux we define two different
page table layout.

The size of pages is in the PGD entry, using PS field (bits 28-29):
00 : Small pages (4k or 16k)
01 : 512k pages
10 : reserved
11 : 8M pages

For 512K hugepage size a pgd entry have the below format
[<hugepte address >0101] . The hugepte table allocated will contain 8
entries pointing to 512K huge pte in 4k pages mode and 64 entries in
16k pages mode.

For 8M in 16k mode, a pgd entry have the below format
[<hugepte address >1101] . The hugepte table allocated will contain 8
entries pointing to 8M huge pte.

For 8M in 4k mode, multiple pgd entries point to the same hugepte
address and pgd entry will have the below format
[<hugepte address>1101]. The hugepte table allocated will only have one
entry.

For the time being, we do not support CPU15 ERRATA when HUGETLB is
selected

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> (v3, for the generic bits)
Signed-off-by: Scott Wood <oss@buserror.net>

show more ...

powerpc/mm: Fixup kernel read only mapping

With commit e58e87adc8bf9 ("powerpc/mm: Update _PAGE_KERNEL_RO") we
started using the ppp value 0b110 to map kernel readonly. But that
faci

powerpc/mm: Fixup kernel read only mapping

With commit e58e87adc8bf9 ("powerpc/mm: Update _PAGE_KERNEL_RO") we
started using the ppp value 0b110 to map kernel readonly. But that
facility was only added as part of ISA 2.04. For earlier ISA version
only supported ppp bit value for readonly mapping is 0b011. (This
implies both user and kernel get mapped using the same ppp bit value for
readonly mapping.).
Update the code such that for earlier architecture version we use ppp
value 0b011 for readonly mapping. We don't differentiate between power5+
and power5 here and apply the new ppp bits only from power6 (ISA 2.05).
This keep the changes minimal.

This fixes issue with PS3 spu usage reported at
https://lkml.kernel.org/r/rep.1421449714.geoff@infradead.org

Fixes: e58e87adc8bf9 ("powerpc/mm: Update _PAGE_KERNEL_RO")
Cc: stable@vger.kernel.org # v4.7+
Tested-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

show more ...