arm64: dts: ti: Add support for AM62-SK

AM62 StarterKit (SK) board is a low cost, small form factor board
designed for TI’s AM625 SoC. It supports the following interfaces:
* 2 GB DDR4 RAM
* x2 Giga

arm64: dts: ti: Add support for AM62-SK

AM62 StarterKit (SK) board is a low cost, small form factor board
designed for TI’s AM625 SoC. It supports the following interfaces:
* 2 GB DDR4 RAM
* x2 Gigabit Ethernet interfaces capable of working in Switch and MAC mode
* x1 HDMI Port with audio + x1 OLDI/LVDS Display interface for Dual Display
* x1 Headphone Jack
* x1 USB2.0 Hub with two Type A host and x1 USB Type-C DRP Port
* x1 UHS-1 capable µSD card slot
* 2.4/5 GHz WLAN + Bluetooth 4.2 through WL1837
* 512 Mbit OSPI flash
* x4 UART through UART-USB bridge
* XDS110 for onboard JTAG debug using USB
* Temperature sensors, user push buttons and LEDs
* 40-pin User Expansion Connector
* 24-pin header for peripherals in MCU island (I2C, UART, SPI, IO)
* 20-pin header for Programmable Realtime Unit (PRU) IO pins
* 15-pin CSI header

Add basic support for AM62-SK.

Schematics: https://www.ti.com/lit/zip/sprr448

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20220225120239.1303821-6-vigneshr@ti.com

show more ...

arch: arm64: ti: Add support J721S2 Common Processor Board

The EVM architecture for J721S2 is similar to that of J721E and J7200. It
is as follows,

+------------------------------------------------

arch: arm64: ti: Add support J721S2 Common Processor Board

The EVM architecture for J721S2 is similar to that of J721E and J7200. It
is as follows,

+------------------------------------------------------+
| +-------------------------------------------+ |
| | | |
| | Add-on Card 1 Options | |
| | | |
| +-------------------------------------------+ |
| |
| |
| +-------------------+ |
| | | |
| | SOM | |
| +--------------+ | | |
| | | | | |
| | Add-on | +-------------------+ |
| | Card 2 | | Power Supply
| | Options | | |
| | | | |
| +--------------+ | <---
+------------------------------------------------------+
Common Processor Board

Common Processor board is the baseboard that contains most of the actual
connectors, power supply etc. The System on Module (SoM) is plugged on to
the common processor baord. Therefore, add support for peripherals brought
out in the common processor board.

Common Processor Board: https://www.ti.com/tool/J721EXCPXEVM

Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20211207080904.14324-6-a-govindraju@ti.com

show more ...

arm64: dts: ti: Add support for J721E SK

J721E Starter Kit (SK)[1] is a low cost, small form factor board designed
for TI’s J721E SoC. TI’s J721E SoC comprises of dual core A72, high
performance vis

arm64: dts: ti: Add support for J721E SK

J721E Starter Kit (SK)[1] is a low cost, small form factor board designed
for TI’s J721E SoC. TI’s J721E SoC comprises of dual core A72, high
performance vision accelerators, video codec accelerators, latest C71x
and C66x DSP, high bandwidth real-time IPs for capture and display, GPU,
dedicated safety island and security accelerators. The SoC is power
optimized to provide best in class performance for industrial and
automotive applications.

J721E SK supports the following interfaces:
* 4 GB LPDDR4 RAM
* x1 Gigabit Ethernet interface
* x1 USB 3.0 Type-C port
* x3 USB 3.0 Type-A ports
* x1 PCIe M.2 E Key
* x1 PCIe M.2 M Key
* 512 Mbit OSPI flash
* x2 CSI2 Camera interface (RPi and TI Camera connector)
* 40-pin Raspberry Pi GPIO header

Add basic support for J721E-SK.

[1] https://www.ti.com/tool/SK-TDA4VM

Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210929081333.26454-3-sinthu.raja@ti.com

show more ...

arm64: dts: ti: iot2050: Add support for product generation 2 boards

This adds the devices trees for IOT2050 Product Generation 2 (PG2)
boards. We have Basic and an Advanced variants again, differin

arm64: dts: ti: iot2050: Add support for product generation 2 boards

This adds the devices trees for IOT2050 Product Generation 2 (PG2)
boards. We have Basic and an Advanced variants again, differing in
number of cores, RAM size, availability of eMMC and further details.
The major difference to PG1 is the used silicon revision (SR2.x on
PG2).

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/cc868da8264324bde2c87d0c01d4763e3678c706.1632657917.git.jan.kiszka@web.de

show more ...

arm64: dts: ti: Makefile: Collate AM64 platforms together

Make sure that the platforms are grouped together per SoC. This helps
keep the Makefile readable as newer platforms get added to the list.

arm64: dts: ti: Makefile: Collate AM64 platforms together

Make sure that the platforms are grouped together per SoC. This helps
keep the Makefile readable as newer platforms get added to the list.

Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20210915121442.27112-1-nm@ti.com

show more ...

arm64: dts: ti: Add support for Siemens IOT2050 boards

Add support for two Siemens SIMATIC IOT2050 variants, Basic and
Advanced. They are based on the TI AM6528 GP and AM6548 SOCs HS, thus
differ in

arm64: dts: ti: Add support for Siemens IOT2050 boards

Add support for two Siemens SIMATIC IOT2050 variants, Basic and
Advanced. They are based on the TI AM6528 GP and AM6548 SOCs HS, thus
differ in their number of cores and availability of security features.
Furthermore the Advanced version comes with more RAM, an eMMC and a few
internal differences.

Based on original version by Le Jin.

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://new.siemens.com/global/en/products/automation/pc-based/iot-gateways/simatic-iot2050.html
Link: https://github.com/siemens/meta-iot2050
Link: https://lore.kernel.org/r/4fb05969102d14d230e03ca4312ef9706efa61e6.1615473223.git.jan.kiszka@siemens.com

show more ...

arm64: dts: ti: Add support for AM642 SK

AM642 StarterKit (SK) board is a low cost, small form factor board
designed for TI’s AM642 SoC. It supports the following interfaces:
* 2 GB LPDDR4 RAM
* x2

arm64: dts: ti: Add support for AM642 SK

AM642 StarterKit (SK) board is a low cost, small form factor board
designed for TI’s AM642 SoC. It supports the following interfaces:
* 2 GB LPDDR4 RAM
* x2 Gigabit Ethernet interfaces capable of working in switch and MAC mode
* x1 USB 3.0 Type-A port
* x1 UHS-1 capable µSD card slot
* 2.4/5 GHz WLAN + Bluetooth 4.2 through WL1837
* 512 Mbit OSPI flash
* x2 UART through UART-USB bridge
* XDS110 for onboard JTAG debug using USB
* Temperature sensors, user push buttons and LEDs
* 40-pin Raspberry Pi compatible GPIO header
* 24-pin header for peripherals in MCU island (I2C, UART, SPI, IO)
* 54-pin header for Programmable Realtime Unit (PRU) IO pins
* Interface for remote automation. Includes:
* power measurement and reset control
* boot mode change

Add basic support for AM642 SK.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210226184251.26451-3-lokeshvutla@ti.com

show more ...

arm64: dts: ti: Add support for AM642 EVM

The AM642 EValuation Module (EVM) is a board that provides access to
various peripherals available on the AM642 SoC, such as PCIe, USB 2.0,
CPSW Ethernet, A

arm64: dts: ti: Add support for AM642 EVM

The AM642 EValuation Module (EVM) is a board that provides access to
various peripherals available on the AM642 SoC, such as PCIe, USB 2.0,
CPSW Ethernet, ADC, and more.

Introduce support for the AM642 EVM to enable mmc boot, including
enabling UART and I2C on the board.

Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/20210226144257.5470-6-d-gerlach@ti.com

show more ...

arm64: dts: ti: Add support for J7200 Common Processor Board

Add support for J7200 Common Processor Board.
The EVM architecture is very similar to J721E as follows:

+-------------------------------

arm64: dts: ti: Add support for J7200 Common Processor Board

Add support for J7200 Common Processor Board.
The EVM architecture is very similar to J721E as follows:

+------------------------------------------------------+
| +-------------------------------------------+ |
| | | |
| | Add-on Card 1 Options | |
| | | |
| +-------------------------------------------+ |
| |
| |
| +-------------------+ |
| | | |
| | SOM | |
| +--------------+ | | |
| | | | | |
| | Add-on | +-------------------+ |
| | Card 2 | | Power Supply
| | Options | | |
| | | | |
| +--------------+ | <---
+------------------------------------------------------+
Common Processor Board

Common Processor board is the baseboard that has most of the actual
connectors, power supply etc. A SOM (System on Module) is plugged on
to the common processor board and this contains the SoC, PMIC, DDR and
basic high speed components necessary for functionality.

Note:
* The minimum configuration required to boot up the board is System On
Module(SOM) + Common Processor Board.
* Since there is just a single SOM and Common Processor Board, we are
maintaining common processor board as the base dts and SOM as the dtsi
that we include. In the future as more SOM's appear, we should move
common processor board as a dtsi and include configurations as dts.
* All daughter cards beyond the basic boards shall be maintained as
overlays.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20200914162231.2535-6-lokeshvutla@ti.com

show more ...

arm64: dts: ti: Makefile: Use ARCH_K3 for building dtbs

To allow lesser dependency and better maintainability use CONFIG_ARCH_K3
for building dtbs for all K3 based devices. This is as per the
discus

arm64: dts: ti: Makefile: Use ARCH_K3 for building dtbs

To allow lesser dependency and better maintainability use CONFIG_ARCH_K3
for building dtbs for all K3 based devices. This is as per the
discussion in [0].

[0] https://lore.kernel.org/linux-arm-kernel/20200908112534.t5bgrjf7y3a6l2ss@akan/

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20200914162231.2535-2-lokeshvutla@ti.com

show more ...

arm64: dts: ti: k3-*: Replace HTTP links with HTTPS ones

Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.

Deterministic alg

arm64: dts: ti: k3-*: Replace HTTP links with HTTPS ones

Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.

Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.

Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Tero Kristo <t-kristo@ti.com>

show more ...

arm64: dts: ti: Add support for J721E Common Processor Board

Add Support for J721E Common Processor board support.
The EVM architecture is as follows:

+---------------------------------------------

arm64: dts: ti: Add support for J721E Common Processor Board

Add Support for J721E Common Processor board support.
The EVM architecture is as follows:

+------------------------------------------------------+
| +-------------------------------------------+ |
| | | |
| | Add-on Card 1 Options | |
| | | |
| +-------------------------------------------+ |
| |
| |
| +-------------------+ |
| | | |
| | SOM | |
| +--------------+ | | |
| | | | | |
| | Add-on | +-------------------+ |
| | Card 2 | | Power Supply
| | Options | | |
| | | | |
| +--------------+ | <---
+------------------------------------------------------+
Common Processor Board

Common Processor board is the baseboard that has most of the actual
connectors, power supply etc. A SOM (System on Module) is plugged on
to the common processor board and this contains the SoC, PMIC, DDR and
basic high speed components necessary for functionality. Add-n card
options add further functionality (such as additional Audio, Display,
networking options).

Note:
A) The minimum configuration required to boot up the board is System On
Module(SOM) + Common Processor Board.
B) Since there is just a single SOM and Common Processor Board, we are
maintaining common processor board as the base dts and SOM as the dtsi
that we include. In the future as more SOM's appear, we should move
common processor board as a dtsi and include configurations as dts.
C) All daughter cards beyond the basic boards shall be maintained as
overlays.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>

show more ...

arm64: dts: ti: Add support for AM654 EVM base board

The EValuation Module(EVM) platform for AM654 consists of a
common Base board + one or more of daughter cards, which include:
a) "Personality Mod

arm64: dts: ti: Add support for AM654 EVM base board

The EValuation Module(EVM) platform for AM654 consists of a
common Base board + one or more of daughter cards, which include:
a) "Personality Modules", which can be specific to a profile, such as
ICSSG enabled or Multi-media (including audio).
b) SERDES modules, which may be 2 lane PCIe or two port PCIe + USB2
c) Camera daughter card
d) various display panels

Among other options. There are two basic configurations defined which
include an "EVM" configuration and "IDK" (Industrial development kit)
which differ in the specific combination of daughter cards that are
used.

To simplify support, we choose to support just the base board as the
core device tree file and all daughter cards would be expected to be
device tree overlays.

Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

show more ...

arm64: dts: ti: Add support for J7200 Common Processor Board

Add support for J7200 Common Processor Board.
The EVM architecture is very similar to J721E as follows:

+-----------

arm64: dts: ti: Add support for J7200 Common Processor Board

Add support for J7200 Common Processor Board.
The EVM architecture is very similar to J721E as follows:

+------------------------------------------------------+
| +-------------------------------------------+ |
| | | |
| | Add-on Card 1 Options | |
| | | |
| +-------------------------------------------+ |
| |
| |
| +-------------------+ |
| | | |
| | SOM | |
| +--------------+ | | |
| | | | | |
| | Add-on | +-------------------+ |
| | Card 2 | | Power Supply
| | Options | | |
| | | | |
| +--------------+ | <---
+------------------------------------------------------+
Common Processor Board

Common Processor board is the baseboard that has most of the actual
connectors, power supply etc. A SOM (System on Module) is plugged on
to the common processor board and this contains the SoC, PMIC, DDR and
basic high speed components necessary for functionality.

Note:
* The minimum configuration required to boot up the board is System On
Module(SOM) + Common Processor Board.
* Since there is just a single SOM and Common Processor Board, we are
maintaining common processor board as the base dts and SOM as the dtsi
that we include. In the future as more SOM's appear, we should move
common processor board as a dtsi and include configurations as dts.
* All daughter cards beyond the basic boards shall be maintained as
overlays.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20200914162231.2535-6-lokeshvutla@ti.com

show more ...

arm64: dts: ti: Makefile: Use ARCH_K3 for building dtbs

To allow lesser dependency and better maintainability use CONFIG_ARCH_K3
for building dtbs for all K3 based devices. This is as pe

arm64: dts: ti: Makefile: Use ARCH_K3 for building dtbs

To allow lesser dependency and better maintainability use CONFIG_ARCH_K3
for building dtbs for all K3 based devices. This is as per the
discussion in [0].

[0] https://lore.kernel.org/linux-arm-kernel/20200908112534.t5bgrjf7y3a6l2ss@akan/

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20200914162231.2535-2-lokeshvutla@ti.com

show more ...

arm64: dts: ti: k3-*: Replace HTTP links with HTTPS ones

Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.

arm64: dts: ti: k3-*: Replace HTTP links with HTTPS ones

Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.

Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.

Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Tero Kristo <t-kristo@ti.com>

show more ...

arm64: dts: ti: Add support for J721E Common Processor Board

Add Support for J721E Common Processor board support.
The EVM architecture is as follows:

+-------------------------

arm64: dts: ti: Add support for J721E Common Processor Board

Add Support for J721E Common Processor board support.
The EVM architecture is as follows:

+------------------------------------------------------+
| +-------------------------------------------+ |
| | | |
| | Add-on Card 1 Options | |
| | | |
| +-------------------------------------------+ |
| |
| |
| +-------------------+ |
| | | |
| | SOM | |
| +--------------+ | | |
| | | | | |
| | Add-on | +-------------------+ |
| | Card 2 | | Power Supply
| | Options | | |
| | | | |
| +--------------+ | <---
+------------------------------------------------------+
Common Processor Board

Common Processor board is the baseboard that has most of the actual
connectors, power supply etc. A SOM (System on Module) is plugged on
to the common processor board and this contains the SoC, PMIC, DDR and
basic high speed components necessary for functionality. Add-n card
options add further functionality (such as additional Audio, Display,
networking options).

Note:
A) The minimum configuration required to boot up the board is System On
Module(SOM) + Common Processor Board.
B) Since there is just a single SOM and Common Processor Board, we are
maintaining common processor board as the base dts and SOM as the dtsi
that we include. In the future as more SOM's appear, we should move
common processor board as a dtsi and include configurations as dts.
C) All daughter cards beyond the basic boards shall be maintained as
overlays.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>

show more ...

arm64: dts: ti: Add support for AM654 EVM base board

The EValuation Module(EVM) platform for AM654 consists of a
common Base board + one or more of daughter cards, which include:
a)

arm64: dts: ti: Add support for AM654 EVM base board

The EValuation Module(EVM) platform for AM654 consists of a
common Base board + one or more of daughter cards, which include:
a) "Personality Modules", which can be specific to a profile, such as
ICSSG enabled or Multi-media (including audio).
b) SERDES modules, which may be 2 lane PCIe or two port PCIe + USB2
c) Camera daughter card
d) various display panels

Among other options. There are two basic configurations defined which
include an "EVM" configuration and "IDK" (Industrial development kit)
which differ in the specific combination of daughter cards that are
used.

To simplify support, we choose to support just the base board as the
core device tree file and all daughter cards would be expected to be
device tree overlays.

Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

show more ...