ARM64: dts: meson-gxl: libretech-cc: add card regulator settle times

Changing the card voltage on the cc is not instantaneous, especially
when switching from 3.3v to 1.8v.

It take at least 30ms for

ARM64: dts: meson-gxl: libretech-cc: add card regulator settle times

Changing the card voltage on the cc is not instantaneous, especially
when switching from 3.3v to 1.8v.

It take at least 30ms for the regulator to go from 3.3v to 1.8v. Add
margin to that to make sure we don't upset the sdcard during the voltage
switch

Fixes: 61ff2af9b278 ("ARM64: dts: fixup libretech cc definition")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

ARM64: dts: meson: add mmc clk gate pins

Add the pinctrl to switch mmc clk pins in gpio (pulled down) mode. This
is necessary to be able to gate the clk outside of the SoC while
keeping it running i

ARM64: dts: meson: add mmc clk gate pins

Add the pinctrl to switch mmc clk pins in gpio (pulled down) mode. This
is necessary to be able to gate the clk outside of the SoC while
keeping it running in the controller

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

ARM64: dts: meson-gxl-libretech-cc: Add GPIO lines names

This patch describes the GPIO lines usage on the LibreTech CC board.

This is useful in the debugfs gpio file and using the cdev gpio API.

S

ARM64: dts: meson-gxl-libretech-cc: Add GPIO lines names

This patch describes the GPIO lines usage on the LibreTech CC board.

This is useful in the debugfs gpio file and using the cdev gpio API.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[khilman: minor whiespace fix]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

ARM64: dts: meson-gx: Add AO CEC nodes

This patch adds the AO CEC node in all the HDMI enabled boards DTS.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilm

ARM64: dts: meson-gx: Add AO CEC nodes

This patch adds the AO CEC node in all the HDMI enabled boards DTS.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

ARM64: dts: meson-gxl-s905x-libretech-cc: fixup board definition

The libretech CC derives less from the p212 than initially thought.
Several voltage regulators are different and the capabilities of

ARM64: dts: meson-gxl-s905x-libretech-cc: fixup board definition

The libretech CC derives less from the p212 than initially thought.
Several voltage regulators are different and the capabilities of the
sdcard and emmc also differ.

Deriving from the p212 is not convient anymore so the libretech is now
derived from s905x definition directly.

Fixes: cd84aff1d981 ("ARM64: dts: meson-gxl: Add Libre Technology CC support")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

ARM64: dts: meson-gxl: Add Libre Technology CC support

Add support for the CC board from Shenzhen Libre Technology
More information about the board are available here:

https://libre.computer/blog/

ARM64: dts: meson-gxl: Add Libre Technology CC support

Add support for the CC board from Shenzhen Libre Technology
More information about the board are available here:

https://libre.computer/blog/

Cc: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

arm64: dts: meson: libretech-cc: add internal DAC support

Add the internal DAC support on the libretech CC. The output of this
DAC is provided on the 3.5mm jack connector.

Signe

arm64: dts: meson: libretech-cc: add internal DAC support

Add the internal DAC support on the libretech CC. The output of this
DAC is provided on the 3.5mm jack connector.

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200506221656.477379-4-jbrunet@baylibre.com

show more ...

arm64: dts: meson: libretech-cc: add initial audio playback support

Add initial audio support limited to HDMI i2s.

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off

arm64: dts: meson: libretech-cc: add initial audio playback support

Add initial audio support limited to HDMI i2s.

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Christian Hewitt <christianshewitt@gmail.com>
Link: https://lore.kernel.org/r/20200421163935.775935-5-jbrunet@baylibre.com

show more ...

arm64: dts: meson: fix leds subnodes name

Fix the leds subnode names to match (^led-[0-9a-f]$|led)

It fixes:
meson-g12b-a311d-khadas-vim3.dt.yaml: leds: 'red', 'white' do not ma

arm64: dts: meson: fix leds subnodes name

Fix the leds subnode names to match (^led-[0-9a-f]$|led)

It fixes:
meson-g12b-a311d-khadas-vim3.dt.yaml: leds: 'red', 'white' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-g12b-s922x-khadas-vim3.dt.yaml: leds: 'red', 'white' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-g12b-odroid-n2.dt.yaml: leds: 'blue' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxbb-nanopi-k2.dt.yaml: leds: 'stat' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxbb-nexbox-a95x.dt.yaml: leds: 'blue' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxbb-odroidc2.dt.yaml: leds: 'blue' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxbb-vega-s95-pro.dt.yaml: leds: 'blue' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxbb-vega-s95-meta.dt.yaml: leds: 'blue' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxbb-vega-s95-telos.dt.yaml: leds: 'blue' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxbb-wetek-hub.dt.yaml: leds: 'system' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxbb-wetek-play2.dt.yaml: leds: 'ethernet', 'system', 'wifi' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxl-s905x-libretech-cc.dt.yaml: leds: 'blue', 'system' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxl-s905d-libretech-pc.dt.yaml: leds: 'blue', 'green' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxm-rbox-pro.dt.yaml: leds: 'blue', 'red' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxm-s912-libretech-pc.dt.yaml: leds: 'blue', 'green' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-sm1-sei610.dt.yaml: leds: 'bluetooth' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-sm1-khadas-vim3l.dt.yaml: leds: 'red', 'white' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200326165958.19274-6-narmstrong@baylibre.com

show more ...

arm64: dts: amlogic: use the new USB control driver for GXL and GXM

Add the correcly architectured USB Glue node and adapt all the Amlogic
GXL and GXM board to the new organization.

arm64: dts: amlogic: use the new USB control driver for GXL and GXM

Add the correcly architectured USB Glue node and adapt all the Amlogic
GXL and GXM board to the new organization.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200326134507.4808-11-narmstrong@baylibre.com

show more ...

arm64: dts: meson: libretech-cc: update model and compatible

Shorten the model description to improve readability in some app GUIs
that show the string. Update compatible to be more desc

arm64: dts: meson: libretech-cc: update model and compatible

Shorten the model description to improve readability in some app GUIs
that show the string. Update compatible to be more descriptive, using
the format of the LaFrite board in meson-gxl-s805x-libretech-ac.dts.

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

arm64: dts: meson: fix mmc v2 chips max frequencies

According the datasheets, emmc v2 chips (gxbb and gxl) don't support
more that 100Mhz in UHS-1 SD modes and HS in SDIO.

Align

arm64: dts: meson: fix mmc v2 chips max frequencies

According the datasheets, emmc v2 chips (gxbb and gxl) don't support
more that 100Mhz in UHS-1 SD modes and HS in SDIO.

Align the max-frequency to 100MHz for UHS-1 and 50MHz for HS

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

arm64: dts: meson: libretech-cc: switch eMMC to 1.8v

While some 3.3v eMMC 4.0 are available from libretech, Only the 1.8v 5.0
modules are recommended and supported for the aml-s905x-cc.

arm64: dts: meson: libretech-cc: switch eMMC to 1.8v

While some 3.3v eMMC 4.0 are available from libretech, Only the 1.8v 5.0
modules are recommended and supported for the aml-s905x-cc.

the 1.8v is provided by LDOs on the eMMC card, from vcc 3.3v

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

arm64: dts: meson: libretech-cc: set eMMC as removable

The eMMC on this board is add-on module which is not mandatory. Removing
'non-removable' property should prevent some errors when b

arm64: dts: meson: libretech-cc: set eMMC as removable

The eMMC on this board is add-on module which is not mandatory. Removing
'non-removable' property should prevent some errors when booting a board
w/o an eMMC module present.

Fixes: 72fb2c852188 ("ARM64: dts: meson-gxl-s905x-libretech-cc: fixup board definition")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Martin Blumenstingl<martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

arm64: dts: meson: Fix mmc cd-gpios polarity

Commit 89a5e15bcba8 ("gpio/mmc/of: Respect polarity in the device tree")
changed the behavior of "cd-inverted" to follow the device tree bind

arm64: dts: meson: Fix mmc cd-gpios polarity

Commit 89a5e15bcba8 ("gpio/mmc/of: Respect polarity in the device tree")
changed the behavior of "cd-inverted" to follow the device tree bindings
specification:
According to SDHCI standard, CD lines are specified as "active low".
Using the "cd-inverted" property means that the CD line is "active high".

Fix the SD card description for meson by setting the cd-gpios as
"active low", according to the boards specifications, and dropping the
"cd-inverted" property.

Fixes: 89a5e15bcba8 ("gpio/mmc/of: Respect polarity in the device tree")
Signed-off-by: Loys Ollivier <lollivier@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

arm64: dts: meson-gx: Add hdmi_5v regulator as hdmi tx supply

The hdmi_5v regulator must be enabled to provide power to the physical HDMI
PHY and enables the HDMI 5V presence loopback fo

arm64: dts: meson-gx: Add hdmi_5v regulator as hdmi tx supply

The hdmi_5v regulator must be enabled to provide power to the physical HDMI
PHY and enables the HDMI 5V presence loopback for the monitor.

Fixes: b409f625a6d5 ("ARM64: dts: meson-gx: Add HDMI_5V regulator on selected boards")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

arm64: dts: meson-gxl-libretech-cc: fix GPIO lines names

The gpio line names were set in the pinctrl node instead of the gpio node,
at the time it was merged, it worked, but was obviousl

arm64: dts: meson-gxl-libretech-cc: fix GPIO lines names

The gpio line names were set in the pinctrl node instead of the gpio node,
at the time it was merged, it worked, but was obviously wrong.
This patch moves the properties to the gpio nodes.

Fixes: 47884c5c746e ("ARM64: dts: meson-gxl-libretech-cc: Add GPIO lines names")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

arm64: dts: meson: libretech: update board model

There is actually several different libretech board with the CC suffix
so the model name is not appropriate here. Update to something mor

arm64: dts: meson: libretech: update board model

There is actually several different libretech board with the CC suffix
so the model name is not appropriate here. Update to something more
specific

Reported-by: Da Xue <da@lessconfused.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

ARM64: dts: meson: disable sd-uhs modes on the libretech-cc

There is a problem with the sd-uhs mode when doing a soft reboot.
Switching back from 1.8v to 3.3v messes with the card, which

ARM64: dts: meson: disable sd-uhs modes on the libretech-cc

There is a problem with the sd-uhs mode when doing a soft reboot.
Switching back from 1.8v to 3.3v messes with the card, which no longer
respond (timeout errors). According to the specification, we should
perform a card reset (power cycling the card) but this is something we
cannot control on this design.

Then the only solution to restore the communication with the card is an
"unplug-plug" which is not acceptable

Until we find a solution, if any, disable the sd-uhs modes on this design.
For the people using uhs at the moment, there will a performance drop as
a result.

Fixes: 3cde63ebc85c ("ARM64: dts: meson-gxl: libretech-cc: enable high speed modes")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Cc: stable@vger.kernel.org
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

ARM64: dts: meson-gxl-s905x-libretech-cc: enable the USB controller

The LibreTech CC ("Le Potato") board provides four USB connectors.
These are provided by a hub which is connected to t

ARM64: dts: meson-gxl-s905x-libretech-cc: enable the USB controller

The LibreTech CC ("Le Potato") board provides four USB connectors.
These are provided by a hub which is connected to the SoC's USB
controller.
Enable the SoC's USB controller to make the USB ports usable. Also turn
on the HDMI_5V regulator when powering on the PHY because (even though
it's not shown in the schematics) HDMI_5V also supplies the USB VBUS.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

ARM64: dts: amlogic: Convert to new-style SPDX license identifiers

Move the SPDX-License-Identifier lines to the top and drop the
license splat.

Signed-off-by: Neil Armstrong <n

ARM64: dts: amlogic: Convert to new-style SPDX license identifiers

Move the SPDX-License-Identifier lines to the top and drop the
license splat.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

ARM64: dts: meson s905x: accept MAC addr from u-boot environment

With the adequate configuration settings, u-boot will loop through the
list of aliases looking for "ethernetX".

ARM64: dts: meson s905x: accept MAC addr from u-boot environment

With the adequate configuration settings, u-boot will loop through the
list of aliases looking for "ethernetX".

By adding an ethernet alias, u-boot can fixup the local-mac-address
property in the kernel's device tree using a value held in its
environment variable ethaddr.

Tested-by: Jorge Ramirez-Ortiz <jramirez@baylibre.com>
Signed-off-by: Jorge Ramirez-Ortiz <jramirez@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

ARM64: dts: meson-gx: Add HDMI_5V regulator on selected boards

On reference boards and derivatives, the HDMI Logic is powered by an external
5V regulator.
This regulator was set by t

ARM64: dts: meson-gx: Add HDMI_5V regulator on selected boards

On reference boards and derivatives, the HDMI Logic is powered by an external
5V regulator.
This regulator was set by the Vendor U-Boot, add the regulator and set it always-on for now.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

ARM64: dts: meson-gxl: Take eMMC data strobe out of eMMC pins

Since the Data Strobe pin is optional, take it out of the default
eMMC pins and add a separate entry.

Signed-off-by

ARM64: dts: meson-gxl: Take eMMC data strobe out of eMMC pins

Since the Data Strobe pin is optional, take it out of the default
eMMC pins and add a separate entry.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...

ARM64: dts: meson-gxl: adjust libretech-cc gpio-line-names

TEST_N gpio has been moved so the gpio-line-names of the cc
must be adjusted accordingly

Signed-off-by: Jerome Brunet

ARM64: dts: meson-gxl: adjust libretech-cc gpio-line-names

TEST_N gpio has been moved so the gpio-line-names of the cc
must be adjusted accordingly

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

show more ...